INA129U2K5
Product Specifications
INA129U2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA129U2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA129U2K5: the plain grade SOIC on a large reel, and the moisture level that is not the same on every row
The INA129U2K5 is the plain grade of the eight pin SOIC body from a 2500 piece large reel, in the catalogue spelling that drops the slash before the quantity. The addendum prints the reel under INA129U/2K5 with RoHS marked as a dash rather than a yes, and prints INA129U/2K5G4 beside it at moisture level 2 with one year of floor life against level 3 and 168 hours on the plain row. Same silicon, same quantity, two handling rules, and the row that arrives decides whether the reel can sit open on a shelf.
Electrically this is the INA128 die with the 49.4 kΩ gain network, so the gain equation is G = 1 + 49.4 kΩ divided by RG and a resistor table written for the competing part gives the expected gain without a change. The offset is specified per gain rather than as a single number: 500 µV divided by gain maximum on the U bin at unity gain, which is 5 µV at a gain of 100. On a calibrated channel that is the row to quote, not the headline.
The INA129U2K5 rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback input |
| Vendor status | Active, production |
| Data sheet | SBOS051G, revised January 2026, shared with the INA128 |
| Addendum row | INA129U/2K5, 2500 pieces on a large reel |
| Grade | U bin, the tighter offset and drift window |
| Gain equation | G = 1 + 49.4 kΩ divided by RG |
| Gain range | 1 to 10,000 V/V |
| Input offset voltage | 500 µV divided by gain maximum on the U bin, 5 µV at a gain of 100 |
| Offset drift | 0.5 µV per degree divided by gain maximum |
| Input bias current | 5 nA maximum on the standard rows, 0.6 nA on the alternate chip origin |
| Voltage noise | 8 nV per root hertz at 1 kHz, 0.2 µV peak to peak from 0.1 to 10 Hz |
| Common mode rejection | 120 dB minimum at a gain of 100 with a 1 kΩ source imbalance |
| Bandwidth | 1.3 MHz at unity gain, 200 kHz at a gain of 100 |
| Input protection | Plus or minus 40 V without damage |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 700 µA typical |
| Body | SOIC, D outline, 8 pins, 4.9 by 6 mm |
| Carrier | 2500 pieces, 330 mm reel, 12.4 mm tape |
| Moisture level | Level 3, 260 degrees, 168 hour floor life |
| Temperature range | Minus 40 to plus 125 degrees |
Tubes, reels and two different moisture levels
The SOIC rows ship 75 pieces in a tube or 2500 pieces on a large reel, and the DIP rows ship 50 pieces in a tube. The carrier decides the handling, not the part: a 75 piece tube is a prototype or a small build, and a 2500 piece reel is a production run that will take months to consume. Between those two there is nothing on the addendum, which is why a build of 500 boards is usually bought as several tubes and hand fed rather than as a partial reel.
The moisture level differs between the carriers on this family. The tube rows are published at level 2 with a one year floor life, and the reel rows at level 3 with a 168 hour floor life, so the same die has a different shop floor rule depending on how it arrived. A level 3 reel that is opened for a partial build has to go back into dry storage or be baked, and a 2500 piece reel can easily sit open across two builds. Reading the level off the label rather than off the part number is the practical control, and INA129U2K5 is the code to check it against.
Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ
The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.
Because of that, INA129U2K5 must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.
Gain error rows, the A grade and the 0.024 per cent window
Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.
Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA129U2K5 the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.
50 µV of offset and half a microvolt per degree
The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA129U2K5 can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.
The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.
5 nA of bias current, and the 0.7 nA special order rows
The standard rows of INA129U2K5 carry a 5 nA maximum input bias current, and the data sheet also prints a second set of rows for parts built from a different chip site origin with 0.7 nA maximum. That second set is not a different part number on the shelf: it is a special order condition, and the distinction matters because a customer who needs the lower bias current has to say so rather than order the base code and hope. On a 1 MΩ source the difference between 5 nA and 0.7 nA is 4.3 mV of offset, which is the difference between a channel that works and one that needs a FET input amplifier instead.
For ordinary bridge and shunt work the 5 nA row is irrelevant. A 350 Ω bridge sees 1.75 µV from it, and a 10 mΩ shunt with a 100 Ω filter sees half a microvolt. Bias current becomes the governing error above roughly 100 kΩ of source resistance, and above a megohm it is the only error worth discussing. The offset current rows are about a tenth of the bias current, so a matched source removes most of it and an unmatched source does not.
The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm
The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.
The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA129U2K5 the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.
Buying INA129U2K5
The order line should name the carrier as well as the code, because the same quantity exists under a G4 row with a different moisture level and a different floor life. A reel that is opened for a first article and then stored has to go back into a dry pack if it is level 3, and the label on the reel is the only record of which level it is. Our date code management page covers that shelf life question and the traceability report page covers what a lot record should carry back to the reel.
On a build that consumes less than a reel, the arithmetic is worth doing: 2500 pieces at a few hundred boards a year is several years of stock on a part with no shelf life limit beyond the moisture level, so the stock cost is small and the exposure to a price move is the real reason to hold it. The plain grade is the right buy unless the channel is calibrated at temperature, in which case the UA bin buys back half the drift window.
Questions that arrive with this part number
Whether INA129U2K5 and INA129U/2K5 are the same part is the first question, and they are: the slash is dropped in some catalogue renderings and kept in the addendum, and the quantity, the body and the marking are the same. The second question is whether the reel can be replaced by the 75 piece tube in a shortage, and it can, because the tube row is active and carries the same silicon at the same grade.
The third is the offset number. The family headline of 50 µV belongs to a different reading of the table, and the row that governs a real channel is 500 µV divided by gain, which at unity gain is the loosest point and at a gain of 100 is 5 µV. A specification written against 50 µV flat will fail on a buffer stage and pass easily on a gain of 100 stage, so the gain has to be on the requirement.