INA126U2K5
Product Specifications
INA126U2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA126U2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA126U2K5: the plain grade SOIC body on a 2500 piece large reel
The INA126U2K5 is the same die and the same SOIC body as the tube part, supplied on a large reel for a production line. The reel is what makes the code worth its own entry: a 2500 piece reel feeds a placement machine without operator intervention, and on a board that carries one channel it is 2500 boards of material, which is a quarter or a half of a year for a mid volume product. The reel also brings a different moisture level than the tube, which changes the shop floor rule rather than the part.
The family specification is unchanged: gain from 5 to 10,000 with one resistor, 250 µV of maximum offset, 3 µV per degree drift, 25 nA bias current and 175 µA per channel from a supply as low as plus or minus 1.35 V. On a production board the number that usually decides the build is the bandwidth at the gain in use, because it sets the scan rate or the loop bandwidth and it cannot be recovered by calibration.
The INA126U2K5 rows as the addendum publishes them
| Part class | Micropower instrumentation amplifier, two op amp, single channel |
| Vendor status | Active, production |
| Data sheet | SBOS062D, revised December 2025 |
| Grade | Plain, the family offset and gain error rows |
| Gain equation | G = 5 + 80 kΩ divided by RG |
| Input offset voltage | 250 µV maximum |
| Offset drift | 3 µV per degree maximum |
| Input bias current | 25 nA maximum |
| Voltage noise | 35 nV per root hertz at 1 kHz |
| Bandwidth | 200 kHz at a gain of 5, 9 kHz at a gain of 100 |
| Output swing | To within 0.75 V of the positive rail and 0.8 V of the negative rail |
| Load capacitance | Stable into 1000 pF |
| Supply range | Plus or minus 1.35 V to plus or minus 18 V |
| Quiescent current | 175 µA typical per channel |
| Body | SOIC, D outline, 8 pins |
| Carrier | 2500 pieces on a large reel |
| Moisture level | Level 3, 260 degrees, 168 hour floor life |
| Temperature range | Minus 40 to plus 85 degrees |
175 µA per channel and the supply window that comes with it
At 175 µA per channel typical and 200 µA maximum, INA126U2K5 is built for a product that runs from a battery or from a loop supply, and the supply window of plus or minus 1.35 V to plus or minus 18 V is what makes that possible. The bottom of the window is low enough that a pair of fresh alkaline cells in series will run the part directly, and the top is high enough for a plus or minus 15 V industrial rack. Nothing in between needs a regulator, which is the point: a channel that does not need a regulator does not need the quiescent current of one either.
The current is quoted per channel and with no load, so the total for a dual INA2126 is twice the figure. What the number does not include is the reference divider. A single supply channel needs a mid rail reference, and a 10 kΩ divider across 5 V draws 250 µA, which is more than the amplifier itself. A 100 kΩ divider draws 25 µA and needs a capacitor to hold it stiff; that trade is made once per board rather than once per channel, and it decides whether the microamp budget survives.
Two op amp topology and why the gain floor is 5
The INA126 is a two op amp instrumentation amplifier rather than the three op amp arrangement used by the larger instrumentation parts, and that choice explains most of what is unusual about it. The first stage is a pair of amplifiers sharing one gain resistor, and the second stage is a difference amplifier that removes the common mode. Fewer amplifiers means less supply current, and it also means the gain cannot go all the way down: the minimum stable gain is 5, and the vendor states that a minimum circuit gain of 5 is what keeps the dc common mode range and the bandwidth usable. On INA126U2K5 there is no resistor value that gives unity gain, so a channel that needs a buffer is a different part.
The gain equation is G = 5 + 80 kΩ divided by RG, which is a different shape from the 1 + 50 kΩ form used by the INA128 family. The five is inside the equation, so the external resistor only ever adds to a gain that is already 5. At a gain of 100 the resistor is 842 Ω, at a gain of 1000 it is 80.4 Ω, and at the top of the range the resistor is a couple of ohms, which is where the resistance of the socket and the wiring starts to matter as much as the resistor itself.
Running from plus or minus 1.35 V and what stops working
The supply floor of plus or minus 1.35 V is the reason this family appears in battery instruments, and it comes with conditions. The input common mode window is quoted relative to the rails and does not shrink with the supply, so at plus or minus 1.35 V the window is roughly plus or minus 0.35 V of usable common mode, which is enough for a bridge running at a 0 V common mode and not enough for anything referenced to the positive rail. The output swing also stops about 0.8 V short of each rail, so the usable signal swing at the floor is under a volt peak to peak.
On a 3 V single supply the same arithmetic gives a 1.5 V reference and a signal window of about a volt, which is workable for a strain gauge and marginal for a thermocouple. The part is not a rail to rail amplifier and should not be treated as one. What the low supply does buy is headroom against a dying battery: the amplifier keeps working while the rail falls, and the failure mode is a signal that runs out of range rather than an amplifier that stops.
250 µV of offset and 3 µV per degree of drift on a bridge channel
The offset row for this family is 250 µV maximum on the plain parts and tighter on the A grade, and the drift row is 3 µV per degree maximum. Against a 10 mV full scale bridge those numbers are 2.5 per cent of range and 0.03 per cent per degree, so the offset is trimmed at the bench and the drift is lived with. Against a 100 mV full scale the offset is a quarter of a per cent and the drift is negligible, which is the region where the part is comfortable and where most pressure and flow transmitters actually sit.
The comparison that matters is against the amplifier the part replaces. A general purpose op amp pair built into an instrumentation front end can easily carry 1 mV of offset and 10 µV per degree, and at that level the drift, not the bridge, sets the annual recalibration interval. Moving to a trimmed instrumentation amplifier buys the interval back. The other half of the budget is the bridge excitation: a 5 V excitation on a 350 Ω bridge draws 14 mA, which is two orders of magnitude more than INA126U2K5 draws, so the current budget is set by the sensor rather than by the amplifier.
Input range, output swing and the 1000 pF load limit
The output stage of INA126U2K5 swings to within about 0.75 V of the positive rail and 0.8 V of the negative rail at the quoted load, and it is stable into 1000 pF. That capacitance limit is the one that catches boards in the field: a cable from the amplifier to a remote indicator is easily a nanofarad, and an amplifier driving a cable without a series resistor will show a step response with a tail that looks like a settling problem. A 100 Ω series resistor at the output isolates the capacitance and costs nothing in a high impedance load.
The input range depends on the common mode voltage and on the differential signal at the same time, which is why the vendor prints it as a graph rather than as a single number. On a plus or minus 15 V supply and a gain of 100 the input window is wide; at a gain of 5 it is wider still, because the input stage has more headroom when it is not amplifying. A channel that has to measure a signal sitting near the positive rail at high gain will clip in the input stage before the output saturates, and the symptom is a reading that stops rising rather than one that pins.
The 80 kΩ term, 0.1 per cent resistors and the resistance you forgot
Gain accuracy on INA126U2K5 is set by the external resistor and by the 80 kΩ term inside the equation, and the internal term is trimmed. What is not trimmed is the resistance from the RG pins to the resistor itself: the socket, the solder joint, the trace and the resistor lead all sit in series with RG, and at a gain of 1000 where RG is 80 Ω a single ohm of that path is 1.25 per cent of gain error. That is why the vendor note says sockets and wiring resistance matter at high gain, and why the resistor should be placed within a few millimetres of the pins.
The resistor itself should be a 0.1 per cent metal film part with a 25 ppm per degree coefficient, and it should be the same type on every channel of a multi channel board so that the channels track rather than each drifting its own way. A 1 per cent resistor at a gain of 100 contributes 1 per cent of gain error before temperature, which is larger than the amplifier gain error row. The cost difference between a 1 per cent and a 0.1 per cent resistor is a few cents, and it is the cheapest accuracy in the whole channel.
Buying INA126U2K5 on the reel
Two numbers decide whether a reel is the right carrier. The first is the annual quantity: a 2500 piece reel on a product that builds 400 boards a year is six years of stock, and the moisture level 3 floor life starts again every time the reel is opened. The second is the feeder: a large reel needs a machine that can take it, and a line with only tube feeders will be opening the reel by hand, which defeats the purpose.
For a build that does justify the reel, the storage rule is the one to write down. Level 3 with a 168 hour floor life means a reel that is opened for a partial run goes back into dry storage or is baked before the next run, and the count of hours is cumulative unless the part is dried. Our date code management page covers how the hours and the date codes are tracked, and the safety stock planning page covers how much reel to hold against a schedule.
Questions that arrive with this part number
Whether the reel and the tube are the same part is the first question and the answer is yes electrically, with the moisture level and the carrier as the only differences. The second is whether a partial reel can be returned to a distributor, and it usually cannot once the seal is broken, which is why the reel quantity should be matched to the build rather than bought as a discount.
The third question is about the gain resistor at a high gain. At a gain of 1000 the resistor is about 80 Ω, and the trace, the solder joint and the resistor lead are all in series with it, so the gain error from the board can exceed the amplifier gain error. Placing the resistor within a couple of millimetres of the RG pins and using a 0.1 per cent part is the fix, and it costs a few cents per channel.