Contact Us

INA126U-2K5

Brand: Texas Instruments
Texas Instruments INA126U-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA126U-2K5 — Power Management & Signal Chain | Superb Automation

INA126U-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA126U-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA126U/2K5: the slash form of the reel code and why the spelling matters at receiving

This entry writes the reel code with a slash, INA126U/2K5, which is the form the vendor addendum prints, while the catalogue also carries a hyphenated string on a separate page. The two are the same part and the same carrier, and the reason to treat them as one page is that a buyer searching either form should land on the same specification rather than on a page that looks like a different device. The distinction to keep is between this spelling question and the quantity question, because on this family the trailing characters do not reliably encode the piece count.

The part is the plain grade SOIC body on a large reel: gain from 5 to 10,000 set by one resistor, 250 µV maximum offset, 3 µV per degree drift, 25 nA bias current, 175 µA per channel and a supply range that starts at plus or minus 1.35 V. It is the production carrier of a family that is otherwise bought in tubes.

The INA126U/2K5 rows as the addendum publishes them

Part classMicropower instrumentation amplifier, two op amp, single channel
Vendor statusActive, production
Data sheetSBOS062D, revised December 2025
Vendor stringPrinted as INA126U/2K5 with a slash
Catalogue stringAlso indexed as INA126U2K5 and INA126U-2K5 on separate pages
Gain equationG = 5 + 80 kΩ divided by RG
Input offset voltage250 µV maximum
Offset drift3 µV per degree maximum
Input bias current25 nA maximum
Bandwidth200 kHz at a gain of 5, 9 kHz at a gain of 100
Supply rangePlus or minus 1.35 V to plus or minus 18 V
Quiescent current175 µA typical per channel
BodySOIC, D outline, 8 pins
CarrierLarge reel, quantity per the addendum row
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees
Related codesINA126U in a 75 piece tube, INA126UA and INA126UA/2K5 in the A grade

Two op amp topology and why the gain floor is 5

The INA126 is a two op amp instrumentation amplifier rather than the three op amp arrangement used by the larger instrumentation parts, and that choice explains most of what is unusual about it. The first stage is a pair of amplifiers sharing one gain resistor, and the second stage is a difference amplifier that removes the common mode. Fewer amplifiers means less supply current, and it also means the gain cannot go all the way down: the minimum stable gain is 5, and the vendor states that a minimum circuit gain of 5 is what keeps the dc common mode range and the bandwidth usable. On INA126U/2K5 there is no resistor value that gives unity gain, so a channel that needs a buffer is a different part.

The gain equation is G = 5 + 80 kΩ divided by RG, which is a different shape from the 1 + 50 kΩ form used by the INA128 family. The five is inside the equation, so the external resistor only ever adds to a gain that is already 5. At a gain of 100 the resistor is 842 Ω, at a gain of 1000 it is 80.4 Ω, and at the top of the range the resistor is a couple of ohms, which is where the resistance of the socket and the wiring starts to matter as much as the resistor itself.

The 80 kΩ term, 0.1 per cent resistors and the resistance you forgot

Gain accuracy on INA126U/2K5 is set by the external resistor and by the 80 kΩ term inside the equation, and the internal term is trimmed. What is not trimmed is the resistance from the RG pins to the resistor itself: the socket, the solder joint, the trace and the resistor lead all sit in series with RG, and at a gain of 1000 where RG is 80 Ω a single ohm of that path is 1.25 per cent of gain error. That is why the vendor note says sockets and wiring resistance matter at high gain, and why the resistor should be placed within a few millimetres of the pins.

The resistor itself should be a 0.1 per cent metal film part with a 25 ppm per degree coefficient, and it should be the same type on every channel of a multi channel board so that the channels track rather than each drifting its own way. A 1 per cent resistor at a gain of 100 contributes 1 per cent of gain error before temperature, which is larger than the amplifier gain error row. The cost difference between a 1 per cent and a 0.1 per cent resistor is a few cents, and it is the cheapest accuracy in the whole channel.

175 µA per channel and the supply window that comes with it

At 175 µA per channel typical and 200 µA maximum, INA126U/2K5 is built for a product that runs from a battery or from a loop supply, and the supply window of plus or minus 1.35 V to plus or minus 18 V is what makes that possible. The bottom of the window is low enough that a pair of fresh alkaline cells in series will run the part directly, and the top is high enough for a plus or minus 15 V industrial rack. Nothing in between needs a regulator, which is the point: a channel that does not need a regulator does not need the quiescent current of one either.

The current is quoted per channel and with no load, so the total for a dual INA2126 is twice the figure. What the number does not include is the reference divider. A single supply channel needs a mid rail reference, and a 10 kΩ divider across 5 V draws 250 µA, which is more than the amplifier itself. A 100 kΩ divider draws 25 µA and needs a capacitor to hold it stiff; that trade is made once per board rather than once per channel, and it decides whether the microamp budget survives.

Bandwidth that falls with gain: 200 kHz at 5, 9 kHz at 100

The bandwidth row is quoted at three gains on this family: 200 kHz at a gain of 5, 9 kHz at a gain of 100 and 1.8 kHz at a gain of 500. That is a steep fall, and it is the price of running the input stage at 175 µA. For a pressure or temperature channel sampled a few times a second it is irrelevant. For a vibration channel or a multiplexed data acquisition front end it is the number that decides whether the part can be used at all, and it has to be read at the gain the channel actually runs rather than at the gain in the headline.

Settling follows the same curve: 30 µs to 0.01 per cent at a gain of 5, 160 µs at a gain of 100 and 1.5 ms at a gain of 500, with a 4 µs overload recovery from a 50 per cent overdrive. On a multiplexed front end the settling time, not the bandwidth, sets the channel scan rate, because the amplifier has to recover from the previous channel before the converter samples. A 16 channel scan at a gain of 100 therefore runs at a few kilohertz at best, and a board that assumes otherwise will show crosstalk that looks like a converter fault.

250 µV of offset and 3 µV per degree of drift on a bridge channel

The offset row for this family is 250 µV maximum on the plain parts and tighter on the A grade, and the drift row is 3 µV per degree maximum. Against a 10 mV full scale bridge those numbers are 2.5 per cent of range and 0.03 per cent per degree, so the offset is trimmed at the bench and the drift is lived with. Against a 100 mV full scale the offset is a quarter of a per cent and the drift is negligible, which is the region where the part is comfortable and where most pressure and flow transmitters actually sit.

The comparison that matters is against the amplifier the part replaces. A general purpose op amp pair built into an instrumentation front end can easily carry 1 mV of offset and 10 µV per degree, and at that level the drift, not the bridge, sets the annual recalibration interval. Moving to a trimmed instrumentation amplifier buys the interval back. The other half of the budget is the bridge excitation: a 5 V excitation on a 350 Ω bridge draws 14 mA, which is two orders of magnitude more than INA126U/2K5 draws, so the current budget is set by the sensor rather than by the amplifier.

Plain grade against A grade on the same die

The A suffix on the PA, UA and EA rows is a tighter offset bin, not a different silicon. Both grades share the 3 µV per degree drift, the 25 nA bias current and the 175 µA supply current, and they differ in the maximum offset and in the gain error window. On a channel with a 10 mV full scale the plain grade consumes 2.5 per cent of the range before trimming and the A grade consumes half of that, which is the difference between a trim circuit that is a convenience and one that is mandatory.

Because the two grades are pin compatible, the choice is made on the specification rather than on the board, and that makes substitution easy in both directions and dangerous in one. Shipping the A grade where the plain grade was ordered costs money and raises no objection. Shipping the plain grade where the A grade was ordered passes incoming inspection only if nobody measures the offset, and fails at the first temperature cycle if somebody does. The grade should therefore sit on the purchase order line rather than in a note.

Buying INA126U/2K5 and reconciling the spelling

The purchase order should use the vendor spelling with the slash, because that is the string a distributor's system matches first, and the receiving inspection should compare the reel label against the order rather than against the catalogue entry. A mismatch between a slash and a hyphen is harmless; a mismatch between a small reel and a large reel is a line stop, and both look like a spelling problem on a screen.

The second control is the grade. This page is the plain grade, and the A grade is a separate code with the same die and footprint. A substitution in either direction passes a functional test and changes the offset window, so the grade belongs on the order line. Our drop in replacement verification page sets out what we check before a grade or a vendor is changed on an approved build.

Questions that arrive with this part number

Whether the slash and the hyphen codes are the same part is the first question, and they are: the same die, the same body, the same carrier, with the slash as the vendor form. The second is whether a distributor will accept either string on a purchase order, and most will, but the confirmation should come back in the vendor form so that the reel label can be checked against it.

The third question is about the A grade substitution. On a channel with a 10 mV full scale the plain grade uses 2.5 per cent of the range for offset and the A grade half of that, so the substitution changes whether a trim is needed rather than whether the board works. That is a decision for the specification, not for the buyer.