Contact Us

INA125U

Brand: Texas Instruments
Texas Instruments INA125U is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA125U — Power Management & Signal Chain | Superb Automation

INA125U

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA125U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA125U: the bridge amplifier with an integrated reference in an SO-16 body

The INA125U is the surface mount member of the bridge amplifier family: the same die as the plastic DIP part, with the pin selectable 1.24, 2.5, 5 and 10 V reference and the 4 to 10,000 gain amplifier, in a 16 pin SO-16 body supplied 40 pieces to a tube. The reason to take this row over the DIP is the same reason as everywhere else in this catalogue: a reflow line does not want a 16 pin through hole part in the middle of a surface mount assembly.

The electrical behaviour is unchanged: 460 µA quiescent, 2.7 to 36 V single supply, 250 µV offset, 2 µV per degree drift, 20 nA bias current, 100 dB common mode rejection, 38 nV per root Hz of noise and a sleep pin that shuts down the amplifier and the reference together.

The INA125U rows as the addendum publishes them

Part classInstrumentation amplifier with precision voltage reference
Vendor statusACTIVE, production data
Data sheetSBOS060
Reference voltages1.24 V, 2.5 V, 5 V and 10 V by pin strap
Gain equationG = 4 + 60 kΩ divided by RG
Gain range4 to 10,000 V/V
Input offset voltage250 µV maximum
Offset drift2 µV per degree maximum
Input bias current20 nA maximum
Common mode rejection100 dB minimum
Quiescent current460 µA
Supply rangeSingle supply 2.7 V to 36 V
BodySOIC, D outline, 16 pins
Carrier40 pieces per tube
Reel siblingINA125U/2K5, 2500 pieces
Grade siblingINA125UA, tighter offset bin, same body
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees

A 16 pin SO-16 is a wider body than the SO-8 that most of this catalogue's amplifiers use, and the extra width is worth knowing at the board stage: the footprint is not interchangeable with a 16 pin narrow body even though the pin count matches. A library footprint chosen by pin count rather than by body width is the kind of mistake that is found at the first assembly, not in review.

The reference pins and the wiring they need

The reference occupies the extra pins, and each of them wants a short, quiet connection. The output pin needs a capacitor close to the body, the tap pins need to be strapped to the correct nodes rather than left floating, and the sense connection should tie to the load rather than to the device pin when the bridge is excited at any distance. A 16 pin body with an unconnected tap pin will produce an output that looks like a low reference and is actually the tap floating.

The ground return for the reference is the other detail. The bridge current returns through the ground plane, and if the reference's ground pin sits on the far side of that current path the reference will move with the bridge current. A separate trace from the reference ground to the star point is the standard arrangement, and it costs one wiring decision rather than a component.

Ratiometric measurement in a reflowed assembly

Because the reference output is a pin, the converter can use it as its reference and the bridge excitation disappears from the measurement equation. That is the cleanest way to build a pressure channel, and it requires that the converter reference input does not load the node. A converter with a switched capacitor reference input draws charge packets, and a 1 µF at the pin supplies them; a converter with a resistive reference input needs a buffer.

The ratiometric arrangement also removes the reference drift from the error budget, which leaves the amplifier offset, the amplifier drift and the bridge itself. On a 10 mV full scale that is the difference between a channel that meets 0.5 per cent over temperature and one that does not, and it costs nothing beyond the wiring choice.

Sleep in a reflowed instrument

The sleep pin is a digital input with a threshold referenced to the supply, and on a 3 V rail a microcontroller output can drive it directly. What the pin does not do is isolate the part: the reference output falls to zero, and any circuit connected to it sees that transition. A converter that is using the reference will see its reference collapse, and if the converter is still converting, the reading is garbage rather than zero.

The sequence therefore matters: put the converter to sleep first, then the amplifier, then the supply if there is a switch. On a battery instrument the sequencing lives in the control software, and it should be written once and reused rather than rediscovered on each board.

Where the SO-16 body and this family fit

A multi channel industrial transmitter with four bridge inputs uses four of these, and four SO-16 parts in one reflow pass is a straightforward assembly. The same board with four 16 pin DIPs needs a second process and four sockets that can corrode in a humid cabinet. The surface mount body is the right answer for anything built in quantity.

The DIP body remains useful for a bench instrument that will be reworked, and for a board that is a copy of an older board. In both cases the part is being used for its function and the package is inherited, which is a legitimate reason to keep it.

Buying INA125U

The tube of 40 is active and the reel sibling is active. The grade decision is between the U and the UA, and on a bridge channel without a trim the A bin is the cheaper way to buy accuracy. The moisture level applies to the tube as well as the reel, so a build that opens four tubes has four exposure records rather than one.

For a bridge instrument the reference accuracy matters as much as the amplifier, and our pin to pin cross reference page lists the front ends we can compare when a specific tap voltage is required, while the PPAP submission checklist page covers the documentation an automotive bridge sensor build needs.

Reflow and stencil for a wide body SO-16

A wide body sixteeen pin package needs a stencil aperture that matches its pitch and a paste deposit that does not bridge, and on a board that also carries 0402 passives the stencil is already fine enough. The failure mode on a wide body is not bridging but insufficient paste on the corner pins, because the body can rock on the paste during placement and lift a corner. A first article x ray or a visual on the corner fillets catches it.

The reflow profile is the standard one for a level 3 part with a 260 degree peak, and the soak is what drives the moisture out of the body. A profile that ramps straight to reflow on a part that has absorbed moisture is the popcorn case, and the damage is internal and shows up as a drift that appears after a thermal cycle rather than at test.

The wide body also has more solder joint area per pin, which helps vibration and hurts nothing else at this current. On a machine mounted transmitter the joint is the part of the assembly that fails last, which is the right way round.

Questions that arrive with this part number

Whether the SO-16 is a narrow or a wide body is the first question, and the answer has to come from the vendor drawing rather than from the pin count. Whether the reference can drive a 350 Ω bridge directly is the second, and it cannot at 2.5 V or above without a pass device. The third is the tap strapping, which is a hardware choice that cannot be changed in the control software.

The fourth is the sleep sequence, which is an interaction between the control software and the board rather than a part specification, and getting it wrong produces readings that look like a failing converter.