Contact Us

DRV8889QPWPRQ1

Brand: Texas Instruments
Texas Instruments DRV8889QPWPRQ1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8889QPWPRQ1 — Power Management & Signal Chain | Superb Automation

DRV8889QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8889QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8889QPWPRQ1: a stepper driver with SPI and stall detection

The DRV8889QPWPRQ1 is the automotive stepper driver with 1/256 microstepping, integrated current sense and a full duplex SPI port, published ACTIVE on a 2500 piece reel. It drives one bipolar stepper at 1.5 A full scale and 2.4 A peak per bridge from a 4.5 to 45 V rail, with 900 mΩ of combined FET resistance. The A suffix in the marking, DRV8889A, denotes the variant with programmable open load detection; the plain DRV8889 row is also live at 2000 pieces, so the two variants share a document and differ in one diagnostic feature.

The SPI port is what separates this part from the DRV8884. Up to 63 devices can be chained on one chip select, each with its own register set, which means a board with eight steppers needs eight chip selects or one chain and no extra pins. Through those registers the controller sets the microstep mode, the decay mode, the torque scaling, the off time and the stall detection thresholds, and reads back the fault registers.

The DRV8889QPWPRQ1 rows as the addendum publishes them

Part classAutomotive stepper driver with SPI and stall detection
Vendor statusACTIVE, production data
Data sheetSLVSEE9E, April 2020, revised November 2025
QualificationAEC-Q100, functional safety capable
Operating voltage4.5 V to 45 V
Full scale current1.5 A per bridge
Peak current2.4 A per bridge
MicrosteppingUp to 1/256
RDS(on), high side, 25 degrees450 mΩ typical, 550 mΩ maximum at 1 A
RDS(on), high side, 125 degrees700 mΩ typical, 850 mΩ maximum
RDS(on), high side, 150 degrees780 mΩ typical, 950 mΩ maximum
Transimpedance gain2.2 V per amp
Trip accuracy, 67 to 100 per cent7.5 per cent
Trip accuracy, 20 to 67 per cent8 per cent
Phase matching2.5 per cent at 1.5 A
Off time settings7, 16, 24 and 32 µs
Slew rate settings10, 35, 50 and 105 V per µs
Supply current5 mA typical, 7 mA maximum
Sleep current2 µA typical, 4 µA maximum
Wake time, A variant to SPI ready100 µs typical, 200 µs maximum
Undervoltage lockout4.15 to 4.35 V falling, 4.25 to 4.45 V rising
Thermal warning and shutdownWarning before shutdown, both reported on the fault pin
BodyHTSSOP with PowerPAD, 24 pins, 7.80 by 6.00 millimetres
Reel row, A variantDRV8889AQPWPRQ1, 2500 pieces, large tape and reel
Reel row, plain variantDRV8889QPWPRQ1, 2000 pieces, large tape and reel
Quad flat rowDRV8889AERQ1, VQFN, 3000 pieces, level 2
MarkingDRV8889A on the A rows, DRV8889 on the plain rows

The 500 piece difference between the two reel rows is easy to miss. A purchase order written against the family name rather than the exact string can land on either carrrier, and the packing quantity changes the minimum buy. The marking also differs by one letter, so the receiving record has to quote the string on the reel label rather than the family name on the drawing.

Stall detection without an encoder

The stall detection compares the back EMF against the applied current signature and flags a stall when the two diverge. It is a pattern detector rather than a position sensor, so it needs a learning cycle on the actual mechanism before it can be trusted, and the vendor provides a tuning procedure for that. Once tuned it gives a headlight levelling or HVAC flap mechanism a way to find its end stop without a switch, which removes a connector and a wire from the door or the dash.

The open load detection in the A variant is the other half of the diagnostics: it can report a disconnected winding, which a stall detector cannot distinguish from a mechanism that has simply reached its stop. That is the practical reason to pay for the A row.

SPI, torque scaling and the current setting

The full scale current is 2.2 V per amp at the reference, so the reference voltage sets the current directly. The torque DAC scales that full scale in software, which means a controller can reduce the holding current after a move without changing any component, and that is where the thermal saving comes from on a mechanism that holds position for hours. The trade is that a reduced holding current also reduces the stall margin, and a mechanism that is bumped while holding can lose position silently.

The 1/256 microstepping is useful for a head up display mirror that has to move in steps smaller than the eye can see, and it is overkill for a flap that moves between two positions. The setting costs nothing in hardware, but it costs processing time, because each microstep is a step pulse and the controller has to generate them at the right rate.

Thermal behaviour at 900 mΩ

Two bridges at 1.5 A full scale dissipate about 4 W at the cold resistance, which is above what the 24 pin pad can move without a good plane. The realistic continuous rating is closer to 0.8 A per bridge, and the data sheet's 1.5 A figure assumes a short duty cycle and adequate copper. The temperature dependent resistance rows are there to make that calculation possible: 450 mΩ at 25 degrees becomes 780 at 150, a 73 per cent increase.

The thermal warning bit in the status register is the useful instrument here. It fires before the shutdown, so a controller can reduce the torque DAC and keep the mechanism working instead of losing it to a fault. That is the one advantage the SPI part has over the step and direction part in a thermal corner.

Buying DRV8889QPWPRQ1

Two live HTSSOP reels, 2500 for the A variant and 2000 for the plain, plus a 3000 piece VQFN at level 2. The A variant is the one most automotive customers specify, because open load detection is usually in the diagnostic requirements. The 2500 piece reel is a reasonable annual quantity for a single mechanism and an awkward one for a platform that uses one part across four mechanisms.

Because the two variants share a data sheet and a package, the reel label is the only reliable identification. Our date code record captures the label string, the marking and the quantity, which is what a traceability audit asks for.

Questions that arrive with this part number

The first is whether the SPI chain can be used with a controller that has only one chip select. It can, with the caveat that a fault on one device in the chain is read by shifting the whole chain, so the fault latency grows with the number of devices. The second is whether the stall detection works at low speed. It does not work below a threshold that depends on the back EMF amplitude, so a mechanism that creeps has to use a switch rather than the detector.

The third is the meaning of the A suffix in a drawing. It is a variant with open load detection, not a revision, and a substitution in either direction changes the diagnostic capability of the product.

The register set is also where the fault record lives. Each device holds its own status word, and a fault in one device of a chain does not stop the others, which is what allows a controller to keep four mechanisms running while it reports the fifth. Clearing a latched fault needs a write to the clear bit or an nSLEEP pulse of 18 to 35 µs, and the two routes have different effects: the register write keeps the configuration, the sleep pulse resets it to the values stored in the device.

For a build that is moving from the step and direction part to this one, the pin to pin page covers the footprint, and the PPAP checklist lists the records an automotive customer expects with the first shipment.