Contact Us

STM8S105C6T6

Brand: ST
ST STM8S105C6T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S105C6T6 — MCU & Embedded Processors | Superb Automation

STM8S105C6T6

ST — MCU & Embedded Processors

Product Overview

The STM8S105C6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S105C6T6: 32 Kbyte Flash STM8S MCU in LQFP48

STM8S105C6T6 is the 32 Kbyte Flash member of the STM8S 8-bit line in a LQFP48 body (7 by 7 mm), with 1024 bytes of true data EEPROM, 2 Kbyte of RAM, 38 general purpose I/O, 10 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.

Order code and memory

Order codeSTM8S105C6T6
Program Flash32 Kbytes
Data EEPROM1024 bytes, 300 kcycle endurance
RAM2 Kbytes
PackageLQFP48, 7 by 7 mm
Pin count48
Maximum general purpose I/O38
External interrupt pins35
High sink outputs16
ADC channels10 of 16
Controller area networknot present
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 10 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

The 105C6 is the access line part on the same 48-pin body as the 207C6, with 32 Kbytes of Flash and 1024 bytes of EEPROM, but only 2 Kbytes of RAM instead of 6 and a 16 MHz clock ceiling instead of 24. The peripheral set is complete for control work: the advanced control timer, two general purpose 16-bit timers, the basic timer, SPI, I2C and one UART.

The two thirds reduction in RAM is the number that changes what firmware can do. A 32 Kbyte application that runs comfortably on a 207C6 has to be re measured for stack depth, receive buffers and any protocol frame buffer before it moves to the 105, and dynamic allocation is not an option at this size.

Sixteen megahertz with zero wait states is the clock ceiling, and the part draws its current accordingly. The 48-pin body still offers 38 I/O, 35 external interrupt inputs, 16 high sink outputs and 10 analog channels, so the reduction from the performance line is in memory and clock, not in pins.

Where this order code fits

Appliance and small drive control where the algorithm fits in 16 MHz and 2 Kbytes of RAM, and where the BOM has to be held down without losing the advanced timer. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

What replaces a 207C6 with less RAM? This part, with 2 Kbytes of RAM against 6 and a 16 MHz ceiling against 24. The pinout is the same family arrangement, so the board can often carry either, but the firmware has to be re sized.

Does it have an advanced control timer? Yes, TIM1 with complementary outputs and dead time insertion, plus two general purpose 16-bit timers and one 8-bit basic timer.

What is the operating voltage? 2.95 to 5.5 V, the same as the performance line, with an internal 16 MHz RC oscillator and a 128 kHz low power oscillator.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Supplier Quality Audit page walks through the checks that keep a substitute from failing on the bench.