STM8L151C4T6
Product Specifications
STM8L151C4T6
ST — MCU & Embedded Processors
Product Overview
The STM8L151C4T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8L151C4T6: 16 Kbyte ultra-low-power STM8L MCU in LQFP48
STM8L151C4T6 is a 16 Kbyte Flash member of the STM8L ultra-low-power line in a LQFP48 body (7 by 7 mm), with 2 Kbytes of RAM, 1 Kbyte of data EEPROM, 41 general purpose I/O, 25 channels on the 12 bit converter and 1 channel of 12 bit DAC. The supply range is 1.8 to 3.6 V, down to 1.65 V at power down and the core runs at up to 16 MHz. This order code has no LCD controller, so every port pin belongs to the application.
Order code and memory
| Order code | STM8L151C4T6 |
| Program Flash | 16 Kbytes |
| Data EEPROM | 1 Kbyte with ECC and read while write |
| RAM | 2 Kbytes |
| Package | LQFP48, 7 by 7 mm |
| Pin count | 48 |
| Maximum general purpose I/O | 41 |
| ADC channels | 25 of the 12 bit converter |
| DAC channels | 1 of 12 bits with output buffer |
| LCD controller | not present on this order code |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 1.8 to 3.6 V, down to 1.65 V at power down |
| Maximum CPU clock | 16 MHz, 16 MIPS peak |
| Run current | 195 uA per MHz plus 440 uA static |
| Halt current | 350 nA typical |
| Active halt | 1.3 uA typical with the real time clock running |
| Low power modes | 5.1 uA typical in low power run, 3 uA in low power wait |
| Wake up time | 4.7 microseconds from halt |
| Analog to digital converter | 12 bit, up to 1 Msps, 25 channels, internal reference voltage and temperature sensor on chip |
| Digital to analog converter | 1 channel of 12 bits with output buffer, 7 microseconds typical settling into 5 k and 50 pF |
| Comparators | 2, one fixed threshold and one rail to rail, both can wake the core |
| Timers | two 16 bit general purpose timers with two channels each, one 16 bit advanced control timer with three channels, one 8 bit timer, beeper timer, window and independent watchdog |
| Serial interfaces | one SPI, one I2C at 400 kHz with SMBus and PMBus, one USART with ISO 7816 and IrDA |
| DMA | 4 channels covering the ADC, the DAC, SPI, I2C, USART and the timers |
| Data EEPROM endurance | 300 kcycle with ECC and read while write |
| Program memory endurance | 10 kcycle, 30 years retention at 85 C |
| Identification | 96 bit unique ID, single wire interface module, USART bootloader |
Points to check before this part goes on a BOM
The C4 is the 16 Kbyte member of the medium density line, and the figure that most often surprises a first time buyer is the RAM: 2 Kbytes, the same as the 32 Kbyte C6 on the same die. Storage for the program does not scale with storage for the variables on this family, so a project that is tight on RAM cannot be rescued by moving up one Flash size. With 1 Kbyte of data EEPROM sitting beside it, plus 41 port pins, the balance of the part is aimed at small instrument panels and battery powered sensors rather than at gateways.
The 48 pin body carries 25 of the converter's channels, and the reference comes in through its own VREF+ and VREF- pins rather than from VDDA. That matters when the rail is a lithium cell that moves between 1.8 and 3.6 V: the measurement stays ratiometric only if the reference is tied to the same node as the sensor supply. Leaving VREF+ on VDDA and reading an absolute sensor such as a band gap gives a reading that drifts with the cell, which is a common cause of a board that passes on the bench and fails two months into the field.
Halt current is 350 nA typical and active halt with the real time clock running is 1.3 uA typical, so an application that wakes once a second and takes a 12 bit conversion fits inside a coin cell budget. The number to watch is the wake up path: 4.7 microseconds out of halt is fast, but every GPIO that is left floating adds leakage at 50 nA per pin, and 41 pins left in the reset state can cost more than the core itself. The port configuration after reset is therefore part of the current budget, not an afterthought.
Where this order code fits
Battery powered sensor nodes, heat meters, utility sub metering front ends and small display boards that spend most of their life in halt and wake on a real time clock. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Component Lead Time Solutions page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Does the 16 Kbyte part have less RAM than the 32 Kbyte part? No. Both C4 and C6 carry 2 Kbytes of RAM and 1 Kbyte of data EEPROM. Only the program array differs, 16 Kbytes against 32 Kbytes.
Can the EEPROM be written while code runs from Flash? Yes. The data EEPROM has read while write capability with ECC, rated 300 kcycles, so calibration and counters can be updated from the running application without stalling the core.
What is the minimum supply voltage? 1.65 V without the brown out reset, 1.8 V with it. The datasheet guarantees 16 MHz across that range, so there is no clock derating as the cell discharges.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.