Contact Us

STM8S207K6T6C

Brand: ST
ST STM8S207K6T6C is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S207K6T6C — MCU & Embedded Processors | Superb Automation

STM8S207K6T6C

ST — MCU & Embedded Processors

Product Overview

The STM8S207K6T6C from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S207K6T6C: 32 Kbyte Flash STM8S MCU in LQFP32

STM8S207K6T6C is the 32 Kbyte Flash member of the STM8S 8-bit line in a LQFP32 body (7 by 7 mm), with 1024 bytes of true data EEPROM, 6 Kbyte of RAM, 25 general purpose I/O, 7 analog inputs and 12 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.

Order code and memory

Order codeSTM8S207K6T6C
Program Flash32 Kbytes
Data EEPROM1024 bytes, 300 kcycle endurance
RAM6 Kbytes
PackageLQFP32, 7 by 7 mm
Pin count32
Maximum general purpose I/O25
External interrupt pins23
High sink outputs12
ADC channels7 of 16
Controller area networknot present
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 7 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

On 32 pins the die keeps the same 6 Kbytes of RAM and the same 32 Kbyte Flash array, but the package gives up I/O: 25 general purpose pins, 23 external interrupt inputs, 12 high sink outputs and 7 analog channels. The thermal budget also changes, because the 32-pin body is rated 360 mW of dissipation at 85 C against 443 mW for the 44, 48, 64 and 80-pin bodies.

Seven analog channels is the hard limit that decides sensor count. A three phase current sense plus a DC link voltage plus two thermistors already uses six, and the seventh is the only spare. Any board that assumes 16 channels from the family headline has to be re counted at the package level.

The trailing C in T6C sits after the temperature field in ST ordering, and it is not a memory or temperature code. It is read together with the reel label, so a buyer matching this line item should match the full string rather than the base name plus a package letter.

Where this order code fits

Sensor nodes, small motor control boards and retrofit modules where board area is the constraint and the serial interfaces carry the data out. The 32-pin part keeps both UARTs, the SPI and the I2C block, so a gateway role is possible on 25 I/O. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

How many I/O does the 32-pin body have? 25 general purpose I/O, of which 12 are high sink outputs, plus 23 external interrupt inputs and 7 ADC channels.

Is the die the same as the 48-pin part? The memory and the core are the same family, but the pin count, the ADC channel count, the CAPCOM channel count and the power dissipation rating all differ. Porting between the two is a pin remap job, not a straight swap.

What is the maximum dissipation? 360 mW at 85 C ambient for the 32-pin package, against 443 mW for the wider bodies.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the One Stop BOM Sourcing page walks through the checks that keep a substitute from failing on the bench.