ADUM1402ARWZ-RL
Product Specifications
ADUM1402ARWZ-RL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADUM1402ARWZ-RL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADUM1402ARWZ-RL: four channels at 90 Mbps, where the supply current is a data rate decision
The ADUM1402ARWZ-RL is an Analog Devices quad-channel digital isolator with two channels in each direction, in a 16-lead wide body SOIC. It transfers dc to 90 Mbps non return to zero, provides 3 V to 5 V level translation between the two sides, and is qualified for automotive applications with operation to 125 C. Supply current per channel at 5 V is 1.0 mA maximum from dc to 2 Mbps, 3.5 mA maximum at 10 Mbps and 31 mA maximum at 90 Mbps; at 3 V the same three points are 0.7 mA, 2.1 mA and 20 mA. Pulse width distortion is 2 ns maximum and channel to channel matching is 2 ns maximum, common mode transient immunity is above 25 kV per microsecond, and an output enable pin puts the outputs in a high impedance state. Isolation is 2500 V rms for one minute under UL 1577 with a 560 V peak working voltage. It is on the analog and mixed-signal IC line card.
31 mA per channel at 90 Mbps is 0.62 W for the package, and that is the thermal limit
Four channels at 31 mA on a 5 V rail draw 124 mA, or 0.62 W, and the 16-lead wide body has to pass that out through its pins. At 10 Mbps the same four channels draw 14 mA and 70 mW, and at 2 Mbps they draw 4 mA. The part is therefore specified at three points because the current is not a constant: it rises with the transition rate. A board that states 90 Mbps and then runs at 10 Mbps has 9 times the thermal margin it budgeted for, and a board that assumes the 2 Mbps current while running at 90 Mbps will overheat the package.
| Parameter | Vendor figure | Derived figure |
|---|---|---|
| Channels | 4, two in each direction | a bidirectional link in one package |
| Data rate | dc to 90 Mbps | 11.1 ns bit period |
| Pulse width distortion | 2 ns maximum | 18 percent of the bit period at full rate |
| Current at 5 V | 1.0, 3.5 and 31 mA per channel | 0.62 W for four channels at 90 Mbps |
| Current at 3 V | 0.7, 2.1 and 20 mA per channel | 2.4 times lower than 5 V at the low rate |
| Isolation | 2500 V rms for one minute, 560 V peak working | 3536 V peak withstand, 6.31 times the working voltage |
| Temperature and package | 125 C, 16-lead wide SOIC | automotive qualified, 7.5 mm body |
Level translation is a feature that removes a whole class of parts
One side can run at 3 V and the other at 5 V, and the isolator translates between them because the two supplies are independent. That removes the level shifter that would otherwise sit on one side of the barrier, which matters in an interface between a 3.3 V processor and a 5 V field bus. The same property means the part can be used as a translator without any isolation requirement, and the 125 C rating makes it usable in an enclosure that has no cooling.
Selection notes
- Channel directionality is fixed by the order code, so the 2/2, 3/1 and 4/0 versions are separate parts and cannot be rewired.
- The output enable pin can put all four outputs in a high impedance state, which allows two isolators to drive one bus.
- The 90 Mbps rate is a non return to zero figure, so a coded link with a 50 percent duty cycle runs at half that payload.
- Common mode transient immunity above 25 kV per microsecond is what allows the barrier to sit across a switching node without a false edge.
Questions buyers ask
Is the 90 Mbps rating a per channel figure? Yes, each channel carries up to 90 Mbps, and the supply current at that rate is per channel as well.
Can a 3.3 V side drive a 5 V side directly? Yes. The two supplies set the two logic levels, and the isolator translates between them.
Digital isolators are compared with optocouplers on pin to pin cross reference, and the checks before a change of isolator family are on how to verify a drop in replacement.
Request Quote — In Stock, 100% New & Original, Full Warranty