LTM8056IY#PBF
Product Specifications
LTM8056IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8056IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTM8056IY#PBF: 58 V in and 48 V out from one module, with 5.4 A at 12 V out
The LTM8056IY#PBF is an Analog Devices buck-boost power module in a 15 mm by 15 mm by 4.92 mm BGA, containing the controller, the switches, the inductor and the support components. Input range is 5 V to 58 V with a 60 V absolute maximum, output range is 1.2 V to 48 V, and the vendor publishes 12 V at 1.7 A from 6 V in, 12 V at 3.4 A from 12 V in and 12 V at 5.4 A from 24 V in. Efficiency reaches 96 percent. Switching frequency is set by a resistor from 100 kHz to 800 kHz, the part synchronises from 200 kHz to 700 kHz, and average input and output current limits are adjustable with monitors on both. A single resistor and a divider plus input and output capacitors complete the circuit. The IY suffix is the BGA body and the PBF suffix is the lead-free finish. It is on the analog and mixed-signal IC line card.
Four quadrant operation is why the input current, not the output current, sizes the connector
In a buck-boost the input current is the larger of the two when the output is above the input. At 12 V out and 5.4 A from 24 V in, the output is 64.8 W and the input is 2.81 A at 96 percent efficiency. At 12 V out and 1.7 A from 6 V in, the output is 20.4 W and the input is 3.54 A, which is more current than the 24 V case despite delivering a third of the power. The same happens at 12 V in and 3.4 A out, where the input is 3.54 A. A connector, a fuse and an input capacitor chosen for the 24 V case will be marginal at 6 V in, and that is the most common mistake made with a module of this class.
| Parameter | Vendor figure | Derived figure |
|---|---|---|
| Input range | 5 V to 58 V, 60 V absolute maximum | 11.6 to 1 span, one part for 12, 24 and 48 V |
| Output range | 1.2 V to 48 V | boost and buck from the same pin without a mode pin |
| 12 V at 6 V in | 1.7 A | 20.4 W out, 3.54 A in at 96 percent |
| 12 V at 12 V in | 3.4 A | 40.8 W out, 3.54 A in |
| 12 V at 24 V in | 5.4 A | 64.8 W out, 2.81 A in |
| Switching frequency | 100 kHz to 800 kHz, synchronisable 200 to 700 kHz | external clock removes beat frequencies in a rack |
| Package | 15 x 15 x 4.92 mm BGA | 225 mm2 footprint, 1107 mm3 |
A module above a certain current is a thermal part, not an electrical one
At 64.8 W out and 96 percent efficiency the module dissipates about 2.7 W, and that heat leaves through the BGA pads into the board. In still air a 225 mm2 footprint can carry a few watts only if the copper under it is continuous and connected to inner layers. The four layer board with a solid ground plane under the module is a thermal decision made before the electrical one, and the 4.92 mm height means the part cannot be shaded by a tall neighbour on the same side.
Selection notes
- The 60 V absolute maximum leaves 2 V of margin on a 58 V rail, so a 48 V backplane with load dump protection is the intended application and a raw automotive rail is not.
- Adjustable average current limits allow the module to act as a current source, which is useful for battery charging and for LED strings.
- Two modules can be paralleled for more current, and the current monitors give the sharing error without an external shunt.
- The output can sit above or below the input with no mode pin, so a 12 V rail that must survive a 6 V brownout needs no separate boost stage.
Questions buyers ask
Can the module be used as a 48 V to 12 V converter at 5 A? Yes, that is 60 W and within the published 5.4 A at 12 V from 24 V. The derating is thermal, so the board copper decides the continuous current.
Is an external inductor needed? No. The inductor is inside the module, which is the reason for the 4.92 mm height. What remains external is the frequency resistor, the feedback divider and the capacitors.
Modules of this class are usually sourced against a long lead time on the discrete equivalent, and the options are on power management cross reference and component lead time solutions.
Request Quote — In Stock, 100% New & Original, Full Warranty