ADUM1250WSRZ-RL7
Product Specifications
ADUM1250WSRZ-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADUM1250WSRZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADUM1250WSRZ-RL7: two bidirectional I2C channels with 560 V of working isolation and a 3536 V test
The ADUM1250WSRZ-RL7 is an Analog Devices hot swappable digital isolator built for I2C buses, with two non-latching bidirectional channels in an 8-lead SOIC. Because each channel carries both directions of an open-drain line, the part replaces the pair of optocouplers and the direction logic that an isolated I2C bus used to need. It sinks 30 mA, runs to 1000 kHz, works from 3.0 V to 5.5 V on each side so it also translates levels, and is specified to 125 C with automotive qualification. The isolation figures are 2500 V rms for one minute under UL 1577 and a maximum working voltage of 560 V peak under VDE 0884-17, alongside IEC 62368-1 and 61010-1 approvals. The ADuM1251 is the same die with one bidirectional and one unidirectional channel, for buses whose clock is not read back. It is on the analog and mixed-signal IC line card.
The one minute figure and the working figure are a factor of 6.3 apart
2500 V rms is 3536 V peak, and the certificate that matters for a service life is the 560 V peak working voltage, which is 396 V rms continuous. Dividing one by the other gives 6.3, and that ratio is why a board rated at 2.5 kV for a routine test cannot be described as a 2.5 kV working barrier. In a 400 V DC bus monitor the 560 V peak figure leaves 160 V of headroom, while a 600 V bus is already outside the certificate even though the test voltage would pass.
| Parameter | Vendor figure | Consequence |
|---|---|---|
| Channels | two bidirectional, non-latching | one line pair each, no direction pin |
| Bus speed | 1000 kHz | fast mode plus, 1 us period |
| Sink capability | 30 mA | 12 mW at a 0.4 V low level |
| Supply and logic | 3.0 V to 5.5 V each side | level translation across the barrier |
| Working voltage | 560 V peak | 396 V rms continuous |
| Withstand | 2500 V rms for 1 minute | 3536 V peak, a test and not a rating |
| Temperature | 125 C, automotive qualified | under bonnet use is inside the window |
| Package | 8-lead SOIC | same footprint as the optocoupler pair it replaces |
Thirty milliamps of sink is what makes 1000 kHz possible
An open-drain bus is pulled up by a resistor and pulled down by the driver, so the fall time is set by the sink current and the bus capacitance. At 30 mA, a 400 pF bus falls from 5 V in about 67 ns, which is 6.7 percent of a 1000 ns bit period and leaves the rest of the period for the rise through the pull-up. That is the whole argument for the part: a photocoupler with a 10 mA output and a 100 ns propagation delay cannot hold a 1 MHz bus, and it also cannot pass a bidirectional line without external steering.
Selection notes
- The hot swap circuitry holds the line inactive while a card is inserted into a live backplane, which is the failure mode that corrupts a running bus.
- The ADuM1251 variant drops to one bidirectional plus one unidirectional channel and is enough when the clock is only driven one way.
- Open-drain outputs on both sides mean the pull-up resistors stay on each side of the barrier, and their values are set by the bus capacitance rather than by the isolator.
- The two channels are independent, so a second bus or an SMBus alert line can share the package.
Questions buyers ask
Does one part really replace two optocouplers? Yes for a two-wire bus. Each channel is bidirectional and non-latching, so the data and clock lines each take one channel and no external steering diode or direction signal is needed.
Can the two sides run at different voltages? Yes, from 3.0 V to 5.5 V independently, which lets a 3.3 V controller talk to a 5 V sensor without a separate translator.
Isolated bus parts are compared across families on pin to pin cross reference, and the sourcing options for a running build are grouped under BOM shortage recovery.
Request Quote — In Stock, 100% New & Original, Full Warranty