Contact Us

LT5560EDD#TRPBF

Brand: Analog Devices
Analog Devices LT5560EDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT5560EDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT5560EDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT5560EDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT5560EDD#TRPBF: a 4 GHz mixer with 9 dBm of input intercept at 10 mA

The LT5560EDD#TRPBF is an Analog Devices double-balanced active mixer that covers 10 kHz to 4 GHz, in a 3 mm by 3 mm DFN. Noise figure is 9.3 dB typical at 900 MHz, conversion gain is 2.4 dB typical, input third order intercept is 9 dBm typical at a 10 mA supply current, and the bias is adjustable from 4 mA to 13.4 mA with one resistor, which moves the intercept to 10.8 dBm at 900 MHz output in the upconverting case at full bias. Local oscillator drive is only -2 dBm, the LO port accepts a single-ended or a differential source, port to port isolation is high because of the balanced structure, and an enable pin drops the part into a low leakage state. Supply range is 2.7 V to 5 V. It is on the analog and mixed-signal IC line card.

Bias current is the variable that matters, and 3.4 to 1 of range is a lot

At 10 mA and 3.3 V the part draws 33 mW, and at 13.4 mA it draws 44.2 mW. What that 34 percent of extra current buys is 1.8 dB of input intercept, from 9 dBm to 10.8 dBm, which is a factor of 1.5 in linear terms. Whether that matters depends on the blocking environment: a receiver with a strong adjacent channel needs the intercept, and a receiver in a quiet band is better served by the 33 mW setting. Because the resistor sets the current, the same board can be built at either operating point, and the difference is measurable on the bench rather than a data sheet guess.

ParameterVendor figureDerived figure
Frequency range10 kHz to 4 GHzone part for HF, VHF, UHF and the 2.4 GHz band
Noise figure9.3 dB at 900 MHz8.5 in linear terms, so the mixer adds 8.5 times the input noise
Conversion gain2.4 dB typicalOIP3 of 11.4 dBm from a 9 dBm input intercept
Bias current4 mA to 13.4 mA, set by one resistor33 mW to 44.2 mW at 3.3 V
Intercept at full bias10.8 dBm upconverting at 900 MHz1.8 dB above the 10 mA figure
LO drive-2 dBma low power synthesiser can drive it directly
Supply and package2.7 V to 5 V, 3 x 3 mm DFNruns from a 3.3 V rail with 18 percent margin

A 2.4 dB conversion gain means the mixer is a loss in the cascade anyway

An active mixer with 2.4 dB of gain is not a stage that recovers system noise figure by itself, because its own 9.3 dB noise figure is 6.9 dB above the gain. In a cascade the mixer's contribution to the system noise figure is reduced by the gain ahead of it, and the gain after it does nothing to help. That is the arithmetic that decides whether an LNA is needed in front: with 15 dB of LNA gain and a 1 dB LNA noise figure, the mixer's 9.3 dB is divided by 31.6 and adds 0.3 dB to the system. With no LNA the mixer sets the whole receive noise figure at 9.3 dB.

Selection notes

  • Single-ended LO drive removes a balun from the local oscillator path, which matters at 2.4 GHz where a balun costs more than the mixer.
  • Port to port isolation comes from the double-balanced topology, so the LO leakage at the RF port is low without an external filter.
  • The enable pin has low off state leakage, so a switched mixer in a multi-band front end does not load the path it is not using.
  • Both upconversion and downconversion are specified, and the intercept figures differ between them, so the direction has to be named when comparing parts.

Questions buyers ask

Is this a replacement for a passive mixer? It is an alternative, not a replacement. A passive mixer needs more LO drive and has conversion loss, and this part trades noise figure for gain and a -2 dBm LO requirement.

Does the bias resistor have to be trimmed per board? No. The current is set by a resistor to ground and the value comes from the data sheet curve, so it is a bill of materials choice rather than a calibration.

Mixers and their surrounding parts are compared on pin to pin cross reference, and the options when a mixer goes short are on BOM shortage recovery.

Request Quote — In Stock, 100% New & Original, Full Warranty