Contact Us

DRV632PWR

Brand: Texas Instruments
Texas Instruments DRV632PWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV632PWR — Power Management & Signal Chain | Superb Automation

DRV632PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV632PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV632PWR: the 2 Vrms line driver built for a 600 ohm load

The DRV632PWR is a stereo audio line driver in a 14 pin TSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists 2 Vrms into a 10 kilohm load from a 3.3 V supply, total harmonic distortion plus noise below 0.01 per cent at 2 Vrms, a signal to noise ratio of 105 decibels, compliance with a 600 ohm load, differential inputs with a single ended output, gain adjustable from 1 to 10 volts per volt by external resistors, a direct current offset below 1 millivolt, ground referenced outputs that remove the coupling capacitors, short circuit protection, click and pop reduction circuitry, an external undervoltage mute and an active mute control.

The 600 ohm compliance is the line that separates this part from the 602. A 600 ohm load is the old broadcast and telecom standard, and it is still written into the input specification of a lot of professional equipment, so a driver that is only specified into 10 kilohms may work into 600 ohms and may not meet its distortion figure. A customer who is feeding a mixing desk or a legacy line input needs this number rather than the 10 kilohm one.

The DRV632PWR rows as the addendum publishes them

Part classStereo line driver, differential input, ground referenced output
Vendor statusACTIVE, production data
Data sheetSLOS681C, January 2011, revised August 2019
Supply range3.0 V to 3.6 V, nominal 3.3 V
Output into 10 kilohm2 Vrms at 3.3 V
Load compliance600 ohm
Distortion plus noiseBelow 0.01 per cent at 2 Vrms into 10 kilohm
Signal to noise105 decibels, A weighted
Direct current offset0.5 mV typical, 1 mV maximum
Supply rejection80 decibels
Output high3.1 V at 3.3 V supply
Output low3.0 V at 3.3 V supply
Gain range1 to 10 volts per volt, per channel resistors
Charge pump frequency200 to 400 kHz, 300 typical
Quiescent current5 mA typical, 14 nominal, 25 maximum at 3.3 V
Mute threshold high60 per cent of the supply
Mute threshold low40 per cent of the supply
Undervoltage mute threshold1.25 V on the sense pin
Output electrostatic protection8 kilovolts IEC on the line outputs
BodyTSSOP, 14 pins
Reel rowDRV632PWR, 2000 pieces, large tape and reel
Tube rowDRV632PW, 90 pieces, tube
MarkingDRV632 on the body
Moisture levelLevel 2 at 260 degrees, one year floor life
TemperatureMinus 40 to plus 85 degrees

The supply window is the tightest row on the table. The part runs from 3.0 to 3.6 V, which is a 3.3 V rail with plus or minus 10 per cent, and there is no 5 V option. A board that shares a 5 V audio rail with the older 602 cannot take this part without a regulator, and that is a board level decision rather than a part substitution. The quiescent current of 14 milliamps typical and 25 maximum is also much higher than the 602, because the charge pump and the output stage are biased harder to reach the 600 ohm load.

What the electrical table fixes

The 1 millivolt direct current offset is what makes the ground referenced output usable without a coupling capacitor. An offset of 1 millivolt into a 10 kilohm input draws 100 nanoamps, which is nothing, and into a 600 ohm input draws 1.7 microamps, which is still nothing. The reason the offset matters is click and pop, because a large offset that appears at power up is a step and a step is a click. The part also carries an active mute and an undervoltage mute, and the undervoltage sense pin trips at 1.25 V, so the mute can be set by a divider from the supply.

The 0.01 per cent distortion figure is at 2 Vrms into 10 kilohms, and the 600 ohm compliance is a separate claim without a distortion figure attached to it in the feature list. A customer who needs 0.01 per cent into 600 ohms should read the operational table and the typical curves rather than the headline. That is the distinction between a part that is specified into 600 ohms and a part that is characterised into 600 ohms.

The charge pump frequency of 200 to 400 kHz is well above the audio band and it is the reason the part needs a clean flying capacitor and a short return path. A charge pump that is not decoupled properly puts a 300 kHz ripple on the output, and a 300 kHz ripple is inaudible but it is not invisible to a following analogue to digital converter. A customer who is driving an ADC rather than a line output should check the ripple against the converter input filter.

Where the body fits on a board

The 14 pin TSSOP is the same body as the rest of the family, and the pin out is compatible with the 602, so a board can move between them if the supply and the load allow it. The moisture level 2 rating gives a one year floor life, which is shorter than the level 1 of the 602 and long enough for a normal build cycle. The 8 kilovolt IEC protection on the outputs means the connector does not need a separate transient array for the audio lines in most products.

The tight supply window puts the regulator choice in the critical path. A 3.3 V rail from a linear regulator with 2 per cent accuracy is fine, and a 3.3 V rail from a switching supply with 5 per cent tolerance and 100 millivolts of ripple is at the edge of 3.6 V. A customer who has built the board around a nominal 3.3 V switching rail should measure the overshoot at load release before accepting the part.

What the documents do not publish

The page gives no distortion curve against load, so the 600 ohm compliance cannot be turned into a distortion figure from the summary. It gives no crosstalk figure between channels and no output impedance, both of which matter when two channels drive a shared connector. It also gives no turn on transient shape, only the mute and pop reduction claims.

The document does not print the external component values for the charge pump and the gain network on the product page. Those are in the application section and they are the ones that decide whether the part meets its numbers on a specific board, because the gain resistors set the noise gain and the flying capacitor sets the pump's strength.

Second source and long term availability

Ground referenced line drivers with an internal charge pump exist from a few vendors and the pin out is not standard, so a cross is a board change with a re-check of the mute logic and the pump capacitors. The amplifier cross reference page sets out what we compare, and the component obsolescence management page covers the watch on a family like this.

The part has been in production since 2011 with a revision in 2019 and the addendum rows are live at 2000 and 90 pieces. Both packings are in the same body, so a change from a tube build to a reel build does not touch the board. A long programme should still ask for a written availability statement rather than infer it from a status column.

What to send with an enquiry

Send the exact string, the packing, the quantity and the date. State the load impedance, because the 600 ohm claim and the 10 kilohm claim are different tests, and state the supply rail and its tolerance, since the part has no 5 V option.

Say whether the output feeds a line input or a converter input, because the charge pump ripple matters to one and not to the other. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.