CC1150RGVR
Product Specifications
CC1150RGVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The CC1150RGVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CC1150RGVR: a sub 1 GHz transmitter with the packet engine inside
CC1150RGVR is a single chip UHF transmitter covering 300 to 348 MHz, 400 to 464 MHz and 800 to 928 MHz, with a programmable data rate up to 500 kBaud and output power up to plus 10 dBm. The RGVR suffix is the 16 pin QLP body, 4 mm by 4 mm, on a large reel.
It is the transmit half of a link, and it is honest about that: there is no receiver in the package. That makes it the right part for a one way system, a sensor that reports and never listens, a remote keyless entry fob, or the transmit side of a link whose receive side is a different device with a better sensitivity.
What separates this part from a bare modulator is the amount of digital work it does. A 64 byte transmit FIFO, sync word insertion, configurable packet length, automatic CRC, optional forward error correction with interleaving, and optional data whitening are all on chip. A cheap microcontroller can therefore drive a complete packet radio over SPI without doing any of the framing in software.
The bands and what each one is for
300 to 348 MHz is the low band, used in some Asian and American legacy products. 400 to 464 MHz covers the 433 MHz industrial, scientific and medical band, which is the busiest of the three in Europe and Asia. 800 to 928 MHz covers the 868 MHz European band and the 915 MHz American band.
The output power is programmable up to plus 10 dBm, which is enough for a few hundred metres at low data rate with a modest antenna and not enough for a kilometre. The document is clear that the part is intended for systems targeting compliance with EN 300 220 and FCC part 15, which means the duty cycle and the channel occupancy rules of those standards apply to the system, not to the chip.
The supply range starts at 1.8 V, which is what makes it usable in a coin cell product. At 1.8 V the output power is lower than at 3.6 V, and the document prints the curves. A specification that asks for plus 10 dBm while the rail is 1.8 V is asking for a number the part will not deliver.
| Function | single chip UHF transmitter |
| Frequency bands | 300 to 348 MHz, 400 to 464 MHz, 800 to 928 MHz |
| Modulation | OOK, ASK, 2-FSK, GFSK and MSK |
| Data rate | up to 500 kBaud, programmable |
| Output power | up to plus 10 dBm, programmable |
| Transmit FIFO | 64 bytes |
| Packet handling | sync word, variable length, automatic CRC |
| Forward error correction | optional, with interleaving |
| Whitening | optional automatic data whitening |
| Frequency synthesizer | fully on chip, fast settling |
| External filters | none required |
| Temperature sensor | integrated analog sensor |
| Interface | SPI, all registers in one burst transfer |
| Supply range | 1.8 V to 3.6 V |
| Package | QLP, 16 pins, 4 mm by 4 mm |
| Standards | EN 300 220 and FCC part 15 targeted |
| Carrier | large tape and reel |
The FIFO is what makes a cheap host possible
Sixty four bytes is small by modern standards and it is exactly the size of a typical sensor report plus its header. A host writes the payload into the FIFO, sets the packet length, strobes the transmit command and goes back to sleep. The radio adds the preamble, the sync word and the CRC, keys the carrier, sends the bytes and reports completion through a status register.
Without that engine the host would have to clock every bit, which rules out the cheapest microcontrollers and the deepest sleep modes. With it, the host can be a part with a few kilobytes of flash and no radio library.
The forward error correction is the other firmware saving. At low data rates in a noisy band the FEC buys several decibels of link margin, and the interleaver spreads a burst error across the codeword so that a single interferer does not destroy the packet. Both are register settings, and both are off by default.
One way links and the systems they serve
The document lists ultra low power UHF wireless transmitters for the 315, 433, 868 and 915 MHz bands, remote keyless entry, home and building automation, wireless alarm and security systems, industrial monitoring and control, wireless sensor networks, automatic meter reading and consumer electronics.
Remote keyless entry is the clearest fit. The fob transmits for a few milliseconds when a button is pressed, the receiver is in the vehicle and is a different part with better sensitivity, and the link is one way by construction. The 64 byte FIFO is far more than a key code needs, and the part spends its life in sleep.
Industrial monitoring is the second fit. A sensor node on a machine reports a value every minute, the receiver is a gateway with a real radio, and the transmit side has to run for years on a battery. At 1.8 V and a low duty cycle this part is one of the few that fits.
Our RF component sourcing page covers the transceiver and transmitter families we hold, and the BOM shortage recovery page describes the substitution route when the transmit half of a link is available and the receive half is not.
The matching network is the part of the project nobody budgets for
The document prints a recommended matching network for each band, and the values are not the same across bands. A board that is built for 433 MHz and then re-tuned for 868 MHz needs different components, a different filter and a fresh compliance test. That is a schedule item, not a component item, and it is the most common surprise on a second band variant.
The second item is the crystal. The synthesizer is on chip and fast settling, which is what makes frequency hopping possible, but the reference is external. A 26 MHz crystal with the right load capacitance is part of the radio, not part of the digital section, and moving it close to the switching supply is the fastest way to lose sensitivity in the receiver at the other end.
The third is the antenna. A 4 mm by 4 mm package with a plus 10 dBm output will deliver a fraction of that into a poor antenna, and the compliance margin at 868 MHz is thin enough that a small mismatch can push a harmonic over the limit.
There is a fourth item that costs more time than any of these: the packet engine is configured by register writes, and the register values depend on the data rate, the deviation and the band. The document prints recommended settings for the common combinations, and a firmware port that carries settings from a 433 MHz board to an 868 MHz board will transmit something, just not something the receiver can decode.
On a one way link that failure is expensive to diagnose, because the transmitter has no way of knowing. Our advice on a new build is to bring up the link with a receiver on the bench before the transmitter is potted or enclosed, and to record the register set that worked alongside the assembly drawing.
The last check is the supply. At 1.8 V the part runs, and at 1.8 V the output power and the frequency accuracy are both reduced. A coin cell product that budgets the link at 3 V and ships at 1.8 V has a shorter range than the bench test suggested, and the document prints the curves that show by how much.
Three questions buyers ask about this string
Can it receive? No. It is a transmitter only. The matching receiver is a separate part number.
Does it need an external PA for 433 MHz? No for the plus 10 dBm class. The document shows an optional external amplifier only for longer links.
Is the SPI interface standard? Yes, four wire, and all registers can be written in one burst, which is what keeps the configuration time short enough for a duty cycled node.