CC8531RHAR
Product Specifications
CC8531RHAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The CC8531RHAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CC8531RHAR: a four channel wireless audio link that still ships in 2026
CC8531RHAR is the 6 mm by 6 mm QFN40 member of the PurePath Wireless family, a 2.4 GHz radio system on chip built for wireless digital audio rather than for data. The family has four members: the CC8520 and CC8521 carry two audio channels, the CC8530 and CC8531 carry four, and the two ending in 1 add a full speed USB audio device. This string is the four channel member with USB, on a 2500 piece reel.
The part is from a 2012 document and it is still in production, which tells a buyer something useful. It is not a candidate for a new consumer product that wants Bluetooth audio, and it is the right part for a product that already has a CC8531 in the field, needs a spare or a last time buy, or wants a fixed latency uncompressed link that a Bluetooth stack cannot offer.
The numbers below come from SWRS091F and from the orderable addendum. The ones that decide whether the part fits are the four channel audio interface, the 10.7 ms latency floor, the plus 3.5 dBm output and the 2.0 V to 3.6 V supply, because this is a part that runs from a battery pack in a headset and from a 3.3 V rail in a speaker.
What the part does that a Bluetooth audio part does not
The link is a fixed, uncompressed, isochronous audio pipe with a latency that can be as low as 10.7 ms and does not drift with retries in the way a packet audio link does. Adaptive frequency hopping, forward error correction, buffering with retransmission and error concealment are all built in, so a crowded 2.4 GHz band degrades gracefully instead of clicking. For a wireless microphone, a stage monitor or a lip sync critical display, that behaviour is worth more than codec support.
Channel count is the other difference. Four channels at 48 kHz and 24 bits is a stereo pair plus two, which is what a 2.1 speaker system or a four channel headset needs. A Bluetooth link in the same band needs a codec and a profile and delivers two channels with a latency measured in tens of milliseconds at best.
| Function | 2.4 GHz radio system on chip for wireless digital audio |
| Family position | CC8531, four audio channels, with USB audio device |
| Radio band | 2.4 GHz, 5 Mbps or 2 Mbps over the air data rate |
| Modulation | bandwidth efficient format with adaptive frequency hopping |
| Output power | up to plus 3.5 dBm, programmable |
| Receiver sensitivity | minus 83 dBm and minus 86 dBm depending on data rate |
| Range extender | CC2590 supported, plus 11 dBm output and minus 87 dBm sensitivity |
| Audio interface | I2S, 1 to 4 channels, 32, 40.275, 44.1 and 48 kHz, 16 or 24 bit |
| Latency | down to 10.7 ms end to end |
| USB | full speed USB audio device, basic audio device class, HID support |
| Control interface | SPI for host control, I2C for external codecs and amplifiers |
| Supply range | 2.0 V to 3.6 V |
| Current, headphone master | 29 mA average |
| Current, headphone slave | 25 mA average |
| Package | QFN40, RHA, 6 mm by 6 mm |
| Ambient range | minus 40 to plus 85 degrees Celsius |
| Carrier | 2500 pieces on a large reel |
| Moisture level | level 3 at 260 degrees, 168 hour floor life |
The latency and channel arithmetic
At 48 kHz a 10.7 ms latency is about 514 samples of audio in flight, which is short enough that a performer hears their own instrument without a perceptible delay and short enough that a video display can be lip synced by delaying the picture rather than the sound. The same figure is why the part appears in stage equipment and not in conference systems, where a 30 ms delay is invisible.
Four channels at 24 bits and 48 kHz is 4.6 Mbps of raw audio, and the 5 Mbps over the air rate is what carries it with the protocol overhead. At the 2 Mbps rate the system trades channel count or word width for robustness, which is the setting used when the band is crowded and the link distance is short. A product that needs four channels at 24 bits should stay on the 5 Mbps rate and accept the shorter range.
Autonomous mode and the host question
The family can run without a host processor: a configuration generated by the PurePath Wireless Configurator is stored in external EEPROM or flash and loaded at boot, with HID functions such as pairing, volume and channel selection mapped to pins. That is how a headset with no firmware team ships. The alternative is a host microcontroller over SPI, which allows a product to change the configuration at runtime and to carry its own user interface.
For a spare parts or last time buy conversation, the autonomous mode is a blessing and a risk. It is a blessing because a customer can rebuild a board without the original firmware source. It is a risk because the configuration file is part of the product, and a customer who has lost it needs the original binary rather than a recompile.
Where the part is a poor fit
It is a poor fit for a new consumer speaker, because a Bluetooth audio part costs less, is available in more packages and has a phone ecosystem behind it. It is a poor fit for a product that needs more than four channels, because the family stops there. It is a poor fit for a product that needs a data link alongside the audio at more than a trickle, because the side channel carries control rather than file transfer.
It is a good fit for an installed product with a long life, a fixed channel count and a latency requirement. That is the class of build where a 2012 part in production is an asset rather than a liability, and it is why we keep the string rather than treat it as obsolete.
Supply and replacement routes
When a customer cannot get this string, there are three honest routes. The first is the sister part without USB, the CC8530, which is the same radio and audio pipeline without the USB device, and which drops into a board that does not use the USB pins. The second is a module built around the same die, which changes the board but keeps the firmware. The third is a new board onto a current part, which is a new product rather than a replacement.
We do not present a Bluetooth audio part as a drop in replacement for this device, because the latency, the channel count and the protocol are all different. The obsolete RF part replacement page sets out how we separate a true replacement from a functional substitute, and the RF component sourcing page covers the passives and the front end parts that go with it.
Ordering and incoming checks
The orderable row prints CC8531RHAR as active and in production, QFN40 with 6 mm by 6 mm body, 2500 pieces on a large reel, NIPDAU lead finish and moisture level 3 at 260 degrees. The RHAT row is the 250 piece small reel and the RHA without a suffix is the tray, so a purchase order that names only the family can land on the wrong carrier.
Incoming inspection for a part this age is mostly about authenticity. Check the reel label against the order code, check the date code against the addendum, confirm the moisture indicator, and check a sample in a fixture if the build is for a product that is still shipping in volume. Because the part is level 3, a reel that has been open for more than 168 hours needs a bake, and a customer who has not planned for that will lose a day at the line.
For a customer building a last time buy, the component lead time solutions page describes how we stage a buffer against a forecast rather than buying a lifetime quantity in one order, which keeps the cash exposure down and the date codes fresh.
Three questions buyers ask about this string
Is this part still in production? Yes, the addendum prints it as active, and the reel quantity is available. A part being old is not the same as a part being discontinued, and the two get confused in a BOM review.
Can it run four channels at 24 bits and 48 kHz? Yes, on the 5 Mbps over the air rate, with the audio interface configured for four channels at 48 kHz and 24 bit words.
Does it need a host processor? No, it can run autonomously from a configuration held in external memory, with pairing and volume mapped to pins. A host is needed only when the product wants to change the configuration at runtime.