Contact Us

DRV5015A1EDBZRQ1

Brand: Texas Instruments
Texas Instruments DRV5015A1EDBZRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5015A1EDBZRQ1 — Power Management & Signal Chain | Superb Automation

DRV5015A1EDBZRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5015A1EDBZRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5015A1EDBZRQ1: An Automotive Hall Latch With 0.7 mT of Hysteresis and a 150 Degree Rating

DRV5015A1EDBZRQ1 is an automotive digital latch Hall effect sensor in a SOT-23 (DBZ) body of 3 pins. The A1 letter is the high sensitivity member, with plus or minus 0.7 mT of typical hysteresis, which is what a magnetic encoder needs when the pole pitch is small and the field at the die is only a few millitesla. It runs from 2.5 V to 5.5 V, sinks 20 mA on an open drain output, and is qualified to AEC-Q100 grade 0, so the ambient rating is minus 40 to plus 150 degrees rather than the 125 degrees of a grade 1 part.

Order code and package

Ordering stringDRV5015A1EDBZRQ1
Family documentDRV5015-Q1, SBAS916B, revised April 2019
PackageSOT-23 (DBZ), 3 pins, 2.92 mm by 1.30 mm
Reel and packing3000 pieces on a large reel
Lead finish and moistureSN, level 1 at 260 C with unlimited floor life
Temperature rangeminus 40 to plus 150 degrees, AEC-Q100 grade 0
ESD classificationHBM level H3A and CDM level C6
Body marking151Z
Output typeOpen drain, 20 mA sink capability
Supply range2.5 to 5.5 V
Sensing bandwidth30 kHz in the features list
Hysteresis, A1 letterplus or minus 0.7 mT typical

Electrical parameters that decide the application

Supply range2.5 to 5.5 V, no separate logic rail
Output current20 mA sink on the open drain output
Output voltage, absolute maximum6.0 V, raised from VCC plus 0.3 V in revision B
Hysteresis, A1 letter0.7 mT typical
Hysteresis, A2 letter1.8 mT typical
Hysteresis, A3 letter1.8 mT typical with an inverted output
ResponseLatched, so alternating north and south poles are needed to toggle the output
Default state at power upLow for the A1 and A2 letters with no field present
Magnetic limits at 125 CPublished as one column, with a wider column for 150 C
Sensing bandwidth30 kHz, which is the number that matters for a high speed ring magnet
Temperature gradeGrade 0, minus 40 to plus 150 degrees ambient
Package thermal pathSOT-23 with the die attached to the lead frame, no thermal pad

Family variants and how they differ

DRV5015A1-Q10.7 mT typical hysteresis, the sensitive member on this page
DRV5015A2-Q11.8 mT typical hysteresis, for a stronger magnet and a dirtier field
DRV5015A3-Q11.8 mT with the output polarity inverted
DRV5013The older latch family, 5 mT class thresholds, different pin behaviour
DRV5023A switch rather than a latch, unipolar, for position rather than rotation
DRV5032The micropower switch family, 1.3 uA at 20 Hz, for battery products

Points to check before this part goes on a BOM

A latch is not a switch, and the difference decides whether the part works at all. The output changes state only when the field crosses through zero from one polarity to the other, so a target that presents the same pole every time leaves the output where it was. A ring magnet on a shaft alternates poles and works, a single magnet on a sliding door does not, and a two pole magnet on a knob gives one count per revolution rather than two.

The 0.7 mT hysteresis of the A1 letter is small enough that mechanical tolerance and stray fields both matter. It is the right choice for a fine pitch encoder where the field at the die is a few millitesla, and the wrong choice beside a motor winding or a steel shaft that carries residual magnetism, because a stray field of a millitesla can hold the output in one state. The A2 letter at 1.8 mT is the safer part in a dirty field.

Grade 0 is the reason to pay for this part rather than a consumer latch. The ambient range reaches 150 degrees, which is what a sensor inside a fuel pump, an electronic power steering motor or a sunroof gearbox sees after a soak, and the magnetic limits are published twice, once to 125 degrees and once to 150, so the switch point drift over the hot end is a stated number and not an extrapolation.

The open drain output sinks 20 mA and pulls up to whatever rail the controller uses, which is what makes the part usable on a 5 V sensor harness with a 3.3 V MCU behind it. The pull up has to be sized for the edge rate the controller needs and for the current the output can sink at the low level, and the rise time on a long harness is set by the cable capacitance, not by the sensor.

The package is 2.92 mm by 1.30 mm and has no thermal pad, so the die temperature follows the board. In a motor end bell the board is the hottest thing in the assembly, and the 150 degree rating is an ambient rating with the part soldered to a board at that temperature. Running the sensor at 20 mA into a pull up adds a few milliwatts, which is small but not zero in a sealed housing.

Where a fine pitch latch is used

An incremental encoder for a motor shaft uses a ring magnet with many pole pairs and two sensors a quarter pitch apart, and the resolution comes from the pole count rather than from the sensor. The 0.7 mT hysteresis is what keeps the output from chattering at each transition when the field gradient is shallow, and the 30 kHz bandwidth sets the maximum electrical frequency the part can follow.

A flow meter or a knob detent uses the same latch on a single magnet, with the output counting once per pass. The part is rated to 150 degrees, so it can sit on a pump housing next to the impeller magnet without a separate temperature budget, and the grade 0 qualification covers the vibration and the thermal cycling that come with the position.

What to check before the part goes on a harness

The field at the die is the number that has to be measured, not the magnet datasheet. A 3 mm diameter magnet at 1.5 mm gives a few millitesla at the sensor, and the same magnet at 4 mm gives a fraction of that, so the mechanical stack up decides whether the A1 letter trips at all. A gaussmeter reading at the final gap is the only honest way to choose between the A1 and A2 letters.

The second check is the polarity convention. The A1 and A2 letters drive low at power up with no field and switch on a south pole, while the A3 letter inverts the output. A board that was built for the A3 and populated with the A1 counts backwards, and the firmware sees a direction reversal rather than a missing pulse, which is harder to find.

Where this order code fits

The part suits a shaft encoder, a flow meter or a knob detent where the pole pitch is small, the ambient reaches beyond 125 degrees and the controller runs on a different rail from the sensor. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Can this part detect a single magnet? No. It is a latch, so the field has to cross zero from one pole to the other to change the output. A single magnet moving towards and away from the part leaves the output in its last state.

How much field does it need? About 0.7 mT of change around zero for the A1 letter, which is a small magnet at a short gap or a larger magnet at a longer one. The A2 letter needs about 1.8 mT and tolerates more stray field.

Is the 150 degree rating an ambient or a junction figure? It is an ambient rating for the grade 0 part, with the magnetic limits published to 150 degrees as well as to 125. The die runs above ambient by the dissipation in the output, which is small at 20 mA.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.