Contact Us

VBQF2205

Brand: VBsemi
VBsemi VBQF2205 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF2205 — Discrete & Power Semiconductors | Superb Automation

VBQF2205

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF2205 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF2205: a minus 20 V P channel switch at 4 milliohm in a 3 by 3 DFN

The VBQF2205 is a P channel trench MOSFET in the eight pin DFN 3 by 3 body with an exposed pad. The product summary prints two conduction rows, 4.0 milliohm typical at a 10 V gate and 26 A, and 6.0 milliohm typical at a 4.5 V gate and 21 A, against a minus 20 V drain to source rating. The absolute maximum table then adds the current ladder that decides whether the part is usable: minus 52 A with the case held at 25 C, minus 40 A at a 70 C case, minus 26 A in 25 C air and minus 21 A in 70 C air.

It is a switch, not a converter stage. The listed applications are load switch and adaptor or battery switch, and the P channel polarity is the reason it exists at all: the device sits in the high side rail with its source tied to the supply, so a gate pulled to ground turns it on and no charge pump is needed. That saves the bootstrapped driver and the quiescent current that comes with it, and it costs a gate drive that has to be referenced to a moving source and a body diode that points the wrong way for reverse blocking.

The two conduction rows are 50 per cent apart and that gap is the whole story of a low voltage gate drive. At 30 A, 4.0 milliohm sheds 3.6 W and 6.0 milliohm sheds 5.4 W, which is the difference between a 3 by 3 package that runs warm and one that runs at its ceiling. On a 12 V rail with a 4.5 V gate drive the upper row is the one that applies, and the 10 V row is only reachable from a rail that has 10 V of gate swing to spare.

The charge side is unusual for a part this size. Total gate charge is 95.3 nC typical and 143 nC maximum at a 10 V gate, and 46.5 nC typical with 70 nC maximum at 4.5 V, so the maximum part needs half again the charge of the typical one. From a 0.3 A driver that is 318 ns on the typical part and 477 ns on the maximum, which is slow enough to matter at any switching frequency above 100 kHz and irrelevant in a load switch that changes state once per power cycle.

The parameter table in full

Drain to source voltageminus 20 V
Gate to source voltage, continuousplus or minus 16 V
On resistance at 10 V gate and 26 A4.0 milliohm typical
On resistance at 4.5 V gate and 21 A6.0 milliohm typical
Continuous drain current, case at 25 Cminus 52 A
Continuous drain current, case at 70 Cminus 40 A
Continuous drain current, ambient at 25 Cminus 26 A
Continuous drain current, ambient at 70 Cminus 21 A
Pulsed drain currentminus 150 A
Continuous source to drain diode current, case at 25 Cminus 40 A
Continuous source to drain diode current, ambient at 25 Cminus 4.5 A
Maximum power dissipation, case at 25 C54 W
Maximum power dissipation, case at 70 C34.7 W
Maximum power dissipation, ambient at 25 C5.0 W
Maximum power dissipation, ambient at 70 C3.2 W
Junction to ambient, 10 s pulse20 C per watt typical, 25 maximum
Junction to case, steady state1.8 C per watt typical, 2.3 maximum
Operating junction and storage rangeminus 55 to plus 150 C
Peak soldering temperature for 10 s260 C
Gate threshold at 250 microampminus 1.0 to minus 2.2 V
Breakdown voltage temperature coefficientminus 15 mV per C
Gate leakage at plus or minus 16 Vplus or minus 100 nA
Drain leakage at 25 C and at 55 C1 and 10 microamp
On state drain current at 10 V gateminus 30 A
Forward transconductance at 26 A58 S
Input, output and reverse transfer capacitance4595, 910 and 813 pF
Total gate charge at 10 V gate95.3 nC typical, 143 nC maximum
Total gate charge at 4.5 V gate46.5 nC typical, 70 nC maximum
Gate source and gate drain charge13.7 and 12.5 nC
Gate resistance at 1 MHz0.4 minimum, 1.9 mean, 3.8 maximum ohm
Turn on delay and rise time at 10 V gate19 and 10 ns typical
Turn off delay and fall time at 10 V gate65 and 13 ns typical
Turn on delay and rise time at 4.5 V gate55 and 52 ns typical
Turn off delay and fall time at 4.5 V gate53 and 25 ns typical
Body diode forward drop at 1 A0.74 V typical, 1.1 V maximum
Body diode reverse recovery time and charge42 ns and 25 nC typical
PackageDFN 3 by 3 with exposed pad, eight pins

What the thermal rows allow in a 60 C cabinet

The 54 W row is the conduction path written once. It only holds with the case at 25 C, and 54 W through the maximum 2.3 C per watt is 124 C of rise, which lands on 149 C, one degree under the limit. The typical 1.8 C per watt gives 97 C of rise and a 122 C junction, so the difference between a good and a marginal thermal stack is already visible in the two thermal rows before a single watt is switched.

In air the row that governs is 5.0 W, and 5.0 W through 4.0 milliohm is 35 A, or through 6.0 milliohm 29 A. The sheet prints minus 26 A at 25 C ambient and minus 21 A at 70 C, which is more conservative than pure conduction arithmetic because the ambient rows also carry the switching loss of a part driven at 100 kHz. Anyone planning to hold 40 A or more has to give the pad a copper area and a heatsink, and then the case rows take over: 52 A through 4.0 milliohm is 10.8 W, which needs 1.8 C per watt to stay at 19 C of rise.

The breakdown coefficient deserves its own line. The table prints minus 15 mV per C on a part whose magnitude is minus 20 V. Over 100 C of junction rise that is 1.5 V, so a hot device breaks down at about 18.5 V in magnitude. A 20 V rail, never mind a 20 V USB power delivery negotiation, leaves nothing behind that margin, and the right reading of this part is a 12 V rail with a 16 V transient clamp rather than a 20 V rail at its absolute maximum.

Where the printed rows in this sheet disagree

The first disagreement is the gate charge headline. The product summary on page one prints 21.5 nC, and the specification table prints 95.3 nC typical at a 10 V gate and 46.5 nC typical at 4.5 V. No row on the sheet produces 21.5 nC, so the summary figure cannot be the total gate charge at either drive level, and a driver sized on the summary would be four times too small. We quote the specification table.

The second is the capacitor set. Reverse transfer capacitance is printed as 813 pF against an output capacitance of 910 pF, which makes the Miller capacitor 89 per cent of the output capacitor. On a trench MOSFET the reverse transfer figure is normally a small fraction of the output figure, and the sheet also prints a gate drain charge of 12.5 nC, which is a small number for a 813 pF Miller capacitor at a 10 V swing. One of those two rows is not measuring what its heading says, and the capacitance curves on page five are the only way to settle it.

The third is the threshold. The table gives minus 1.0 V minimum and minus 2.2 V maximum with no typical column, so a circuit that relies on a 1.6 V typical turn on is relying on a number the sheet does not publish. For a P channel part used as a load switch this matters on the release side: a gate pulled to the source through a 100 k resistor and released into a 4.5 V rail with 2.2 V of threshold has 2.3 V of overdrive, and at low temperature the threshold moves up rather than down.

Where a minus 20 V, 52 A P channel part still fits

The natural position is a high side switch on a 5 V or 12 V rail where the current is tens of amps and the board has room for a 3 by 3 pad. Battery packs, adaptor inputs, docking connectors and hot swap front ends on a 12 V bus are all inside both the voltage and the thermal envelope. At 12 V and 20 A the conduction loss is 1.6 W at 4.0 milliohm, and 1.6 W through 20 C per watt in still air is 32 C of rise, which fits a 70 C cabinet without a heatsink.

It is a poor fit for a 20 V rail for the reason above, and a poor fit for any position that needs reverse blocking, because the body diode conducts from drain to source in the forward direction and a P channel body diode points into the load. A back to back pair, or an N channel part with a charge pump, is the answer there. It is also a poor fit for a linear current limiter: at 5 V and 20 A in a linear mode the part is dissipating 100 W and the case rows stop at 54 W.

For the sourcing side, our power management cross reference work holds the on resistance at both gate levels, the gate charge spread between the typical and maximum part, and the safe operating area per approved alternate, because two minus 20 V P channel parts at 4 milliohm can differ by 50 per cent in conduction at a 4.5 V gate and by a factor of two in the charge that decides the edge rate.

Questions we answer before a reel is booked

The first is the drive level. If the gate only ever sees 4.5 V, the part is a 6.0 milliohm device and the 52 A row shrinks to 40 A at a 70 C case; if the gate sees 10 V, it is a 4.0 milliohm device with 143 nC of maximum charge, which at 100 kHz is 71 mW of gate drive from a 10 V rail. The gate resistance spread of 0.4 to 3.8 ohm then decides how much of that charge arrives as a fast edge and how much as heat in the driver.

The second is the diode. A load switch that feeds a capacitive load and then sees the supply removed will pull current through the body diode from the load back into the rail, and the ambient diode current row is minus 4.5 A, not minus 40 A. Ask what the load does at power down before accepting the part in that position; a series Schottky or a second FET in the reverse direction is the usual answer.

The third is the alternate. The pin to pin comparison starts from the 3 by 3 footprint, the pad geometry and the pin one orientation rather than from the current rating, because the eight pin 3 by 3 DFN is not one footprint across vendors and the pad under the die differs in area by a factor that shows up in the junction to case row. The incoming inspection plan then checks the arriving lot against the on resistance at both gate levels, the gate charge and the marking, which is the only way to know which of the two summary rows a delivered reel actually follows.