Contact Us

VBQF2216

Brand: VBsemi
VBsemi VBQF2216 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF2216 — Discrete & Power Semiconductors | Superb Automation

VBQF2216

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF2216 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF2216: a minus 20 V P channel switch with an 8 V gate ceiling

The VBQF2216 is a P channel trench MOSFET in the eight pin DFN 3 by 3, and the first row a reader should notice is not the on resistance but the gate rating: plus or minus 8 V. That single figure moves the part into a different class from the 16 V or 20 V gate devices next to it in the same catalogue, because a 10 V gate drive is outside the rating and the 4.5 V row, not the 10 V row, is the operating point.

At that operating point the product summary prints 16 milliohm typical at 4.5 V and 7.0 A, and 20 milliohm typical at 2.5 V and 5.6 A, against a minus 20 V drain to source rating. The current ladder in the absolute maximum table runs minus 15 A with the case at 25 C, minus 12 A at a 70 C case, minus 10 A in 25 C air and minus 8 A in 70 C air. The listed applications are load switch and battery switch, which is exactly the sort of position where a 4.5 V gate comes from a battery rail rather than from a regulated driver.

The 2.5 V row is what makes this part interesting for a single cell product. Twenty milliohm at 2.5 V and 5.6 A means the device still conducts when the gate is driven from a rail that has sagged to 2.5 V, and the threshold window of minus 0.6 V typical is low enough that a 2.5 V rail still gives nearly 2 V of overdrive. The price appears in the timing rows: at a 4.5 V gate the rise time is 89 ns typical and 134 ns maximum, against 13 and 20 ns at a 10 V gate, and the turn on delay goes from 10 ns to 38 ns over the same change.

The thermal envelope is narrower than the current rating suggests. Maximum dissipation is 40 W at a 25 C case, 27 W at 70 C, 2.5 W in 25 C air and 1.6 W in 70 C air, and the junction to foot path is 24 C per watt typical and 30 maximum. Fifteen amps through 16 milliohm is 3.6 W, which is 86 C of rise on the typical foot path and 108 C on the maximum, so the part is comfortable on copper and marginal without it.

The parameter table in full

Drain to source voltageminus 20 V
Gate to source voltage, continuousplus or minus 8 V
On resistance at 4.5 V gate and 7 A16 milliohm typical
On resistance at 2.5 V gate and 5.6 A20 milliohm typical
Continuous drain current, case at 25 Cminus 15 A
Continuous drain current, case at 70 Cminus 12 A
Continuous drain current, ambient at 25 Cminus 10 A
Continuous drain current, ambient at 70 Cminus 8 A
Pulsed drain currentminus 150 A
Continuous source to drain diode current, as printedminus 2.1 A at case 25 C and minus 45 A at ambient 25 C
Maximum power dissipation, case at 25 C40 W
Maximum power dissipation, case at 70 C27 W
Maximum power dissipation, ambient at 25 C2.5 W
Maximum power dissipation, ambient at 70 C1.6 W
Junction to ambient, 10 s pulse40 C per watt typical, 50 maximum
Junction to ambient, steady state95 C per watt maximum
Junction to foot, steady state24 C per watt typical, 30 maximum
Operating junction and storage rangeminus 55 to plus 150 C
Gate threshold at 250 microampminus 0.6 V typical, no window published
Breakdown voltage temperature coefficientminus 31 mV per C
Gate leakage at plus or minus 8 Vplus or minus 100 nA
Drain leakage at 25 C and at 55 C1 and 5 microamp
On state drain current at 10 V gateminus 40 A
Forward transconductance at 7 A18 S
Input, output and reverse transfer capacitance1500, 180 and 145 pF
Total gate charge at 10 V gate25 nC typical, 38 nC maximum
Total gate charge at 4.5 V gate13 nC typical, 20 nC maximum
Gate source and gate drain charge3.5 and 5.5 nC
Gate resistance at 1 MHz0.4 minimum, 2.0 mean, 4.0 maximum ohm
Turn on delay and rise time at 10 V gate10 and 13 ns typical
Turn off delay and fall time at 10 V gate23 and 9 ns typical
Turn on delay and rise time at 4.5 V gate38 and 89 ns typical
Turn off delay and fall time at 4.5 V gate22 and 11 ns typical
Body diode forward drop at 5.6 A0.71 V typical, 1.2 V maximum
Body diode reverse recovery time and charge22 ns and 17 nC typical
PackageDFN 3 by 3, eight pins

What the thermal rows allow in a 60 C cabinet

The 40 W row does not survive contact with the thermal table. Forty watts through the typical 24 C per watt foot path is 960 C of rise, and the same 40 W through the maximum 30 C per watt is 1200 C, so the dissipation row is a package and lead frame limit rather than a reachable operating point. The reachable figure from the same rows is 125 C of rise divided by 24, which is 5.2 W on the typical path and 4.2 W on the maximum.

Five watts is 17.7 A through 16 milliohm, and the sheet prints minus 15 A at a 25 C case, so the current row and the thermal row agree closely once the real path is used. In still air the 50 C per watt figure allows 2.5 W for a 125 C rise, which is 12.5 A at 16 milliohm, and the sheet prints minus 10 A, again slightly conservative because the ambient rows carry switching loss as well as conduction.

The steady state ambient row of 95 C per watt is the one that catches people. A 3 by 3 package soldered to a small pad with no copper spreading reaches that figure, and 95 C per watt allows 1.3 W, which is 9 A at 16 milliohm. The 10 s pulse row of 50 C per watt assumes a square inch of copper and a transient that has not yet heated the board, and reading it as a continuous figure doubles the current a build can actually carry.

Where the printed rows in this sheet disagree

The diode current rows are printed the wrong way round. The table lists minus 2.1 A with the case at 25 C and minus 45 A with the ambient at 25 C, while the drain rows in the same table fall from 15 A at a case of 25 C to 10 A in air. A diode current of 45 A in air against a 15 A drain rating in the same package is not physically reachable, and the minus 2.1 A figure matches the ambient row of a smaller sibling rather than this part. We treat both rows as unconfirmed and ask for the corrected sheet.

The gate charge headline is the second. Page one prints 16 nC in the product summary, and the specification table prints 25 nC typical and 38 nC maximum at a 10 V gate, with 13 nC typical at 4.5 V. The summary figure sits between the two table rows, so it is either a 4.5 V measurement taken on a different sample or a typographical merge of the two, and a driver sized on it lands 30 per cent low.

The threshold is the third. Only a typical value of minus 0.6 V is printed, with no minimum and no maximum, on a part whose whole commercial point is operation from a 2.5 V gate. A threshold distribution that is not published cannot be checked against a 2.5 V rail at minus 10 per cent, and the 20 milliohm row at 2.5 V is a typical row as well, so the guaranteed conduction at the bottom of the gate range is simply not on the sheet.

The fourth is small but worth naming. The product summary row for drain voltage is blank in the extracted table while the absolute maximum table prints minus 20 V, and the summary current column carries a footnote marker that refers to a case temperature the summary does not state. Neither changes a decision, both are signs that the summary was assembled from a different revision than the specification page.

Where a minus 20 V, 15 A part with an 8 V gate still fits

The fit is a battery fed load switch or a battery reverse polarity guard on a 5 V to 12 V rail, where the gate is driven from a rail that never exceeds 8 V and the current stays inside 10 A in air. A single cell product that needs to keep conducting down to a 2.5 V gate is the strongest case, since the 20 milliohm row is specified there and the threshold leaves room for it.

It is a poor fit anywhere a 10 V gate drive is already on the board, and the pairing of an 8 V gate ceiling with a 16 V gate neighbour in the same 3 by 3 body is exactly the kind of substitution that fails on the bench rather than in the catalogue. It is also a poor fit for a hot swap position: the 150 A pulsed row looks generous, but the safe operating area at 12 V and 20 A is not published, and a hot swap event is a simultaneous high voltage and high current pulse that only a published area curve can clear.

On the sourcing side, the power management cross reference work records the gate ceiling as a hard attribute next to the on resistance, because the two parts that look like drop in replacements on current and voltage differ by a factor of two on gate rating. Our drop in replacement check puts the gate ceiling, the threshold window and the diode direction ahead of the current rating for exactly this reason.

Questions we answer before a reel is booked

The first is which gate rail the board actually provides. At 4.5 V this is a 16 milliohm part with a 89 ns rise time; at 2.5 V it is a 20 milliohm part and the driver has to deliver 6 nC into a threshold that is only specified as a typical. Ask for the gate waveform at the coldest specified temperature, because the threshold moves away from the rail as the junction cools.

The second is the pulsed row. Minus 150 A is a 300 microsecond, 2 per cent duty figure, and a load switch turning into a shorted output will see a pulse of exactly that shape while the current limit reacts. Without a published safe operating area the only honest answer is a fuse or a current limited source in front of the part.

The third is the diode behaviour at power down. This part will conduct from the load back into the rail through its body diode, the ambient diode current row is the ambiguous one printed above, and a capacitive load that discharges into a dead rail is the case that exposes it. Our incoming inspection plan measures the body diode drop and the on resistance at both gate levels on every lot for this family, since the printed rows on this particular sheet cannot be taken at face value.