DLPA3000DPFD
Product Specifications
DLPA3000DPFD
Texas Instruments — Power Management & Signal Chain
Product Overview
The DLPA3000DPFD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DLPA3000DPFD: the projector power management IC in the 100 pin HTQFP
The DLPA3000DPFD is a power management IC for DLP Pico projector systems, built as a 100 pin HTQFP measuring 14.00 by 14.00 millimetres and supplied 90 pieces in a JEDEC tray. The vendor carries the part as ACTIVE and lists an RGB LED driver with an integrated buck converter good for up to 6 A of LED current, low resistance RGB channel switches, 10 bit programmable current per channel, two buck converters for the display controller and the digital micromirror supply, a third 8 bit programmable buck for a fan or an auxiliary rail, two low dropout regulators at 2.5 V and 3.3 V for up to 200 mA, an analogue multiplexer for a thermistor and reference nodes, and thermal shutdown, hot die, low battery and undervoltage protection.
The three supplies that make this part what it is are the micromirror bias, reset and offset rails, which have to come up in a defined order and sit at defined levels. They are generated on chip from a dedicated regulating supply, and the sequencing is controlled over SPI rather than by external delays. That is why a projector board with this part has fewer discrete components around the mirror than one built from separate converters, and why a fault in the sequence shows up as a display symptom rather than as a supply symptom.
The DLPA3000DPFD rows as the addendum publishes them
| Part class | Power management IC with an integrated RGB LED driver |
| Vendor status | ACTIVE, production data |
| Data sheet | DLPS052A, October 2015, revised September 2023 |
| LED current | Up to 6 A per channel from the integrated buck |
| Current setting | 10 bits per channel, register programmable |
| Buck converters | Five, two dedicated to the controller and mirror supply |
| Auxiliary buck | 8 bit programmable, fan or auxiliary rail |
| Low dropout regulators | Two, fixed at 2.5 V and 3.3 V, 200 mA each |
| Mirror supplies | Bias, reset and offset generated on chip |
| Input voltage | 6 V to 20 V on the supply pins |
| Switch and feedback pins | 0.1 V to 20 V |
| Logic and SPI pins | 0.1 V to 3.6 V, SPI supply 1.7 V to 3.6 V |
| Ambient temperature | 0 to 70 degrees |
| Junction temperature | 0 to 120 degrees |
| Thermal, junction to ambient | 7.0 degrees per watt with the vendor heatsink |
| Thermal, junction to case | 0.7 degrees per watt |
| Body | HTQFP, 100 pins, 14.00 by 14.00 millimetres |
| Tray row | DLPA3000DPFD, 90 pieces, JEDEC tray |
| Reel row | DLPA3000DPFDR, 1000 pieces, large tape and reel |
| Marking | DLPA3000D on the reel body |
| Moisture level | Level 2 at 260 degrees, one year floor life |
| Lead finish | Nickel palladium gold |
| Protection | Thermal shutdown, hot die, low battery, undervoltage lockout |
The tray row is 90 pieces and the reel row is 1000 pieces, and the two are not interchangeable on a line. A JEDEC tray is a hand load or a tray feeder, and a 1000 piece reel needs a feeder that can take the carrier width. The moisture level 2 rating gives one year of floor life, which is generous for a package this size and is the reason a tray can sit on a bench through a build without a bake.
What the electrical table fixes
The thermal figure of 7.0 degrees per watt is quoted with a specific heatsink, a 22 by 22 by 12 millimetre aluminium pin fin part with a 20 by 20 by 8 millimetre fan, and a 100 micrometre layer of 3 watt per metre kelvin grease. It is not a natural convection number. A board that runs this part without that heatsink cannot use 7.0 degrees per watt, and the vendor says so in the footnote rather than in the headline, which is the sort of thing that gets lost when a thermal calculation is copied from a summary.
The 6 A LED current is a buck converter output, so the input current is lower and the dissipation is spread across the switch, the inductor and the LED string. The RGB switches are described as very low on resistance, and the sequencing between channels is break before make, which is the detail that keeps two LED strings from being connected to the same driver at once. The 10 bit current setting gives 1024 steps across the range, which on a 6 A full scale is about 6 mA per step, and the accuracy of that step is a data sheet figure rather than a feature line.
The ambient rating of 0 to 70 degrees is narrow. This is a consumer projector part, not an industrial one, and a customer who plans to put it in an enclosure that reaches 60 degrees inside is working with 10 degrees of margin before the junction limit at 120 degrees. With the quoted 7.0 degrees per watt and a 10 watt dissipation, the rise is 70 degrees, which is the whole margin. The thermal path is therefore the whole problem, and the electrical margins are secondary.
Where the body fits on a board
A 100 pin HTQFP at 14 millimetres square carries 25 pins per side at half millimetre pitch, which needs a four layer board at minimum and a stencil with a thin aperture for the paste. The thermal pad is on the top of the package and the vendor expects the heatsink to sit on the case, so the board is not the only thermal path and the mechanical stack up matters as much as the copper. A customer who has only built the board and not the heatsink has built half the thermal solution.
The SPI interface runs at 1.7 to 3.6 V on its own supply pin, which lets the part talk to a 1.8 V controller without a level shifter, and the rest of the logic pins are 3.6 V maximum. The analogue multiplexer brings a thermistor and internal nodes out to an external converter, which means the controller needs one ADC channel rather than several, and that is a real reduction in the controller pin count on a small projector board.
What the documents do not publish
The product page gives the LED current and the buck count but no efficiency curve, and efficiency is the number that decides the heatsink. It gives no inductor values, no switching frequency and no output capacitor requirements in the summary, all of which are in the application section of the full document. A customer who is costing a board from the page will miss the passive count by a wide margin.
The page also gives no register map and no default state for the supplies, so the power up sequence has to be taken from section eight. That is the section that says which rail comes up first and how long the delay is, and a board that brings the mirror supplies up out of order will show a fault that looks like a dead panel. The revision history also notes that unsupported converter blocks were removed from the feature list in the current revision, so an older board that used them cannot be carried forward on the same document.
Second source and long term availability
A power management IC built around a specific display controller and a specific mirror has no true second source, because the sequencing and the register map are tied to the display part. A cross means a new board and a new display controller. The component obsolescence management page covers the planning question, and the last time buy and lifetime buy planning page covers what to do when the vendor signals an end of life.
The 3005 sibling in the same package carries the higher current version of the same function and it already has a lifebuy row on the older C suffix, which is a reminder that this family moves. A programme built on the 3000 should track the status of both parts, because a shortage on one is often followed by a status change on the other.
What to send with an enquiry
Send the exact string, the packing you need, the quantity and the date. State the LED current per channel and the number of channels, because 6 A is a ceiling and the thermal calculation depends on the actual current. State whether the heatsink and fan are part of the assembly, since the quoted thermal resistance assumes they are.
Send the display controller part number as well. This IC is tied to a controller family and a mirror, and a quote without those two is a quote for a part that may not sequence with the rest of the board. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.