Contact Us

CDCLVC1108PWR

Brand: Texas Instruments
Texas Instruments CDCLVC1108PWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CDCLVC1108PWR — Power Management & Signal Chain | Superb Automation

CDCLVC1108PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CDCLVC1108PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CDCLVC1108PWR: the 1:8 LVCMOS clock buffer on a 2000 piece reel

The CDCLVC1108PWR is the eight output member of the CDCLVC11xx family, a group of LVCMOS clock buffers that share one die structure and one pin out so that a board can move from two outputs to twelve without a second footprint. The vendor product page carries the family as ACTIVE and describes a 1.2 to 1.12 fan out range across seven members, a pin to pin skew under 50 picoseconds, an additive jitter under 100 femtoseconds, a supply of 3.3 V or 2.5 V, a maximum clock of 250 MHz at 3.3 V and 180 MHz at 2.5 V, and an operating range of minus 40 to plus 85 degrees. The sixteen pin small outline body is 5.00 by 4.40 millimetres.

The reel row behind the string is 2000 pieces in a large tape and reel, nickel palladium gold lead finish, moisture level 1 at 260 degrees, and the body marking is C9C8 rather than the orderable string. Moisture level 1 matters here more than it does on a power part, because a level 1 reel goes onto the line without a bake and a level 3 reel does not. A clock buffer sits near the middle of a board that is usually built in small runs, so the packing question arrives earlier than the price question.

The CDCLVC1108PWR rows as the addendum publishes them

Part class1:8 LVCMOS clock buffer, one input, eight outputs
FamilyCDCLVC1102 to CDCLVC1112, seven members, 1:2 through 1:12
Vendor statusACTIVE, production data
Data sheetSCAS895B, May 2010, revised February 2017
Supply range, 3.3 V row3.0 V to 3.6 V, nominal 3.3 V
Supply range, 2.5 V row2.3 V to 2.7 V, nominal 2.5 V
Maximum clock250 MHz at 3.3 V, 180 MHz at 2.5 V
Additive jitter100 femtoseconds rms, 12 kHz to 20 MHz, 250 MHz out
Pin to pin skew50 picoseconds, equal load on every output
Pulse skew180 picoseconds at 3.3 V, 220 at 2.5 V
Part to part skew0.5 nanoseconds at 3.3 V, 1.2 at 2.5 V
Propagation delay0.8 to 2.0 nanoseconds at 3.3 V, 1.0 to 2.6 at 2.5 V
Rise and fall0.3 to 0.8 nanoseconds, 20 to 80 per cent
Enable and disable time6 nanoseconds at 3.3 V, 10 at 2.5 V
Static supply current6 mA typical, 10 mA maximum at 3.6 V
Power down current60 microamps with the enable pin low
Output impedance45 ohms at 3.3 V, 60 ohms at 2.5 V
Output high2.5 V at 8 mA, 2.2 V at 12 mA, 3 V supply
Output low0.5 V at 8 mA, 0.8 V at 12 mA, 3 V supply
Input thresholdHalf the rail plus or minus 600 mV at 3.3 V, 400 mV at 2.5 V
Minimum pulse width1.8 nanoseconds at 3.3 V, 2.75 at 2.5 V
Input slew rate1 to 4 volts per nanosecond
BodyTSSOP, 16 pins, 5.00 by 4.40 millimetres
Reel rowCDCLVC1108PWR, 2000 pieces, large tape and reel, Active
Tube rowCDCLVC1108PW, 90 pieces, tube, Active
MarkingC9C8 on the 16 pin body
Thermal, 16 pin108.4 degrees per watt junction to ambient
ESD4000 V human body, 1500 V charged device

Two rows on that table decide whether an order can be matched. The tube row at 90 pieces and the reel row at 2000 pieces are both live, and both sit in the same sixteen pin body, so a pilot run and a production run use the same land pattern and only the packing changes. The marking differs from the string, which is the reason a receiving inspection that reads the top of the package and compares it with the purchase order will open a discrepancy that does not exist.

What the electrical table fixes

The additive jitter figure is quoted as 100 femtoseconds rms from 12 kHz to 20 MHz at 250 MHz output, and it is a measured floor, not a claim about the clock source. A buffer adds jitter to whatever arrives, so the number that reaches a converter is the source jitter plus this contribution in the root sum sense, and a 100 femtosecond part behind a 300 femtosecond oscillator is not a 100 femtosecond clock. The 50 picosecond pin to pin skew is the figure that matters when eight lines feed eight converters that sample at the same instant, because it sets how far apart their sampling edges can land.

Drive is quoted at two currents and two rails. At 3 V the output holds 2.5 V into 8 mA and 2.2 V into 12 mA, so a 50 ohm line terminated at the far end is inside the 8 mA point and a 33 ohm load is not. The 45 ohm output impedance at 3.3 V is the number to use with a series resistor when a long trace needs damping, because the source impedance plus the series resistor should land near the line impedance. Input thresholds are centred on half the rail with a plus or minus 600 mV window at 3.3 V, which is a wide window and explains why the part accepts a slow edge, while the 1 to 4 volts per nanosecond input slew requirement sets the floor on how slow.

The minimum pulse width of 1.8 nanoseconds at 3.3 V is the ceiling on frequency in disguise. A 250 MHz clock has a 2 nanosecond half period, which is above the limit by a small margin and no more, so a board that runs the part at 250 MHz with a duty cycle that is not close to 50 per cent is running outside the pulse width requirement even though the frequency is inside the headline. The pulse skew of 180 picoseconds then converts that margin into output duty cycle error, and the vendor gives the formula for that conversion in the switching table footnote rather than in the feature list.

Where the body fits on a board

The sixteen pin small outline body measures 5.00 by 4.40 millimetres and carries a 108.4 degree per watt junction to ambient figure, which at the 10 mA maximum static current and a 3.6 V rail is a dissipation of 36 milliwatts and a rise of about 4 degrees above ambient. Thermal is therefore not the constraint on this part. The constraint is the eight outputs and the track width that eight 50 ohm lines need when they leave the package on one side, and that is a routing question that starts at the pin out rather than at the data sheet.

The family pin compatibility is the practical feature. A board that carries the sixteen pin body can accept the fourteen, twenty or twenty four pin member only if the land pattern is drawn for the largest, since the pin count changes with the fan out. A customer who expects to grow from six to ten outputs after a first article should draw the twenty pin footprint and fit the sixteen pin part, and that decision belongs to the first pass at the footprint, not to the second build. The vendor states that all members are pin compatible to each other, which is true within the pin count they share and is not a promise across pin counts.

What the documents do not publish

The product page gives one additive jitter number at 250 MHz and one at 180 MHz, and no jitter figure at any lower frequency, so a 25 MHz clock tree cannot be signed off from the page. It also gives no output to output crosstalk figure and no supply rejection figure, both of which matter when eight outputs switch into eight separate loads on one die. Those tables are in the full document, and the page should not be treated as a specification when a customer forwards a screenshot of it as the requirement.

The second gap is packaging. The addendum prints the tube and reel rows and the tape and reel section prints the pocket dimensions, but the product page prints neither, so a customer who needs a carrier tape drawing for an automated line has to pull the package materials section of the same document. The third gap is the enable pin behaviour at power up, which the page describes in one sentence and the functional description explains across a page, and that difference matters when eight outputs must come up in a defined state behind a hot plug rail.

Second source and long term availability

A clock buffer of this class is available from several vendors and the numbers are close enough that a cross is usually possible, but the pin out and the jitter floor are not identical, so a cross has to be checked against the source clock and the load rather than against the frequency alone. The pin to pin cross reference page sets out what we compare before a candidate is offered, and the component obsolescence management page covers what happens when a family keeps the reel rows and closes the tube rows.

The CDCLVC11xx family has run since 2010 with two revisions, one of which changed the pin numbers of two outputs on the twenty pin member. That is the kind of change that does not touch the sixteen pin part but does touch a board that was drawn for the larger body, and it is the reason a revision letter is worth reading before a second source is proposed. A customer who has been buying the same string for years may still be holding a drawing from the earlier revision.

What to send with an enquiry

Send the exact string, the pin count, the quantity and the date you need it. State the input frequency and the number of outputs that are actually loaded, because the supply current and the jitter both depend on how many outputs switch. If the board is already drawn for a different member of the family, say which one, since the land pattern and the pin count decide whether the part can be substituted at all.

Send the clock source as well. A buffer is judged against the source it follows, and a quote for a 100 femtosecond part behind a 2 picosecond oscillator is a quote for a part that will not fix the problem. The BOM scrubbing page explains how we reconcile a line like this against the build quantity and the packing before a schedule is confirmed.