Contact Us

CD74HC123E

Brand: Texas Instruments
Texas Instruments CD74HC123E is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD74HC123E — Power Management & Signal Chain | Superb Automation

CD74HC123E

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD74HC123E from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD74HC123E: dual retriggerable monostable multivibrator with reset

CD74HC123E is the one-shot that turns an edge into a defined pulse without a clock in a PDIP body of 16 pins. Each half of the part produces a pulse whose width is set by one resistor and one capacitor, with the width given as 0.45 times the product at 5 V. Both halves are retriggerable, both have a reset input, and the trigger inputs accept a rising or a falling edge. The part runs from 2 V to 6 V, drives 15 low power Schottky loads, and holds 30 percent noise immunity at 5 V.

Order code and package

Order codeCD74HC123E
Functiondual retriggerable monostable multivibrator with reset
Trigger inputsA falling edge and B rising edge, plus a reset per half
Timingexternal resistor and capacitor per half
Pulse width0.45 times resistance times capacitance at 5 V
Minimum resistance5 kohm typical
Minimum capacitance0 pF
Supply2 to 6 V on the HC version
PackagePDIP, 16 pins, 19.30 mm by 6.35 mm
Temperature rangeminus 55 to plus 125 C on the M suffix, wider than the E suffix body
DatasheetSCHS166 revision C
Output drive15 low power Schottky loads

Electrical parameters that decide the application

Pulse width law0.45 R C at 5 V, so a 100 kohm resistor and a 10 nF capacitor give 450 microseconds
Minimum resistance5 kohm typical, below which the discharge transistor is loaded and the width law stops holding
Retriggera new edge during the pulse extends it, which is how a missing pulse detector is built
Reseta low level on the reset pin ends the pulse immediately, independent of the timing components
Noise immunity30 percent of the supply at 5 V, so a 5 V rail gives 1.5 V of immunity on each side
Output drive15 low power Schottky loads, which is enough to drive a buffer or a small relay driver
Supply2 to 6 V for the HC version, against 4.5 to 5.5 V for the TTL compatible version
Temperaturethe M suffix parts are specified from minus 55 to plus 125 C
Replacement notethe 123 triggers on a negative to positive reset pulse; the 423 in the same family does not
PackagePDIP 16, with SOIC and TSSOP bodies in the same family

Points to check before this part goes on a BOM

The pulse width law is 0.45 R C at 5 V, and the coefficient moves with the supply. A board that changes from 5 V to 3.3 V keeps the same resistor and capacitor and gets a shorter pulse, so the value has to be recalculated rather than carried over.

The minimum resistance is 5 kohm typical. Below that the internal discharge transistor carries too much current and the width stops following the law, which shows up as a pulse that is shorter than the sum suggests and varies with temperature.

Capacitor leakage is in parallel with the timing resistor and it charges the same node. A 10 microfarad electrolytic with a microamp of leakage behaves like a 1 Mohm resistor in parallel, so long pulses with large capacitors need a low leakage part rather than the cheapest one on the shelf.

Retriggering extends the pulse, which is what a missing pulse detector wants: the output stays high as long as edges keep arriving and falls one pulse width after the last one. The same behaviour is wrong for a debounce circuit, where the second edge should restart a fixed window rather than stretch it.

Reset is independent of the timing network, so a controller can end a pulse early. The pin is active low and has to be driven rather than left floating, because an open CMOS input is not a defined level.

The 123 and the 423 in the same family differ in the trigger behaviour on the reset pin, and the pinout does not announce it. A substitution between the two changes how a pulse train is interpreted at the input.

Where this order code fits

Boards that need a defined pulse width without a clock usually compare this part with a small controller timer before adding parts to the BOM. Boards comparing it with a neighbouring part start from our BOM Shortage Recovery page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

How is the pulse width calculated? 0.45 times the resistance times the capacitance at a 5 V supply, with a minimum resistance of about 5 kohm.

Does a second trigger restart or extend the pulse? It extends it, which is the retriggerable behaviour and is what a missing pulse detector relies on.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.