CD4518BE
Product Specifications
CD4518BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4518BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4518BE: the dual BCD up counter in a 16-lead plastic DIP
The CD4518BE is the plastic dual in line entry for the CD4518B, two identical internally synchronous four stage BCD counters in a 16-lead body. The vendor page lists the device as ACTIVE with four bits, a counter function, a standard CMOS input, a push pull output and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD4518BE.
Each half is a four stage counter that counts from zero to nine and rolls over, and the two halves can be cascaded to make a two digit counter. The clock and enable lines are interchangeable, so the counter can increment on a positive edge or on a negative edge depending on which pin is driven and which is held. That flexibility is the reason the part appears in older instruments where the edge polarity was fixed by a sensor rather than chosen by an engineer.
The CD4518B rows as the addendum publishes them
| Part class | Two four stage BCD up counters |
| Vendor descriptor | Dual BCD up counter, 4 bits per section |
| Vendor status | ACTIVE, catalogue rating |
| Data sheet | SCHS097 or later revision, acquired from Harris Semiconductor |
| Package addendum date | 18 September 2026 |
| Supply range | 3 V to 18 V, 20 V type rating in the headline |
| Clock frequency | 6 MHz typical at 10 V |
| Triggering | Positive or negative edge, clock and enable interchangeable |
| Carry | Synchronous internal carry propagation |
| Reset | High level on the reset line clears the counter |
| Output drive | Standard CMOS push pull, 4 mA class |
| Input current | 1 microamp at 18 V over temperature, 100 nA at 25 degrees |
| Noise margin | 1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V |
| PDIP body | 16 leads, 181.42 square millimetres, 19.3 by 9.4 mm |
| PDIP rows | CD4518BE, CD4518BE.A and CD4518BEE4, 25 pieces, Active |
| SOIC tube row | CD4518BM, Obsolete, blank quantity, Call TI |
| SOIC reel row | CD4518BM96, 2500 pieces, Active |
| SOP reel row | CD4518BNSR, 2000 pieces, Active |
| TSSOP rows | CD4518BPW tube Obsolete, CD4518BPWR reel 2000 Active |
| Ceramic rows | CD4518BF and CD4518BF3A, 25 pieces, Active |
| Companion device | CD4520B dual binary up counter on the same document |
| Related device | CD40110B up down counter with display drive |
The companion is the part that often gets mixed up with this one. The CD4520B is the binary version and the CD4518B is the BCD version, they share a document, a pin out and a footprint, and the difference only appears when the count passes nine. A board that expects a decimal digit and receives a binary count looks correct for the first ten counts and then shows a value nobody can read. The orderable strings differ by one digit in the same way.
What the count and the carry do
Six megahertz typical at 10 V is the clock figure, and it is a typical rather than a guaranteed maximum. The carry is synchronous inside one section, which means the four stages change together and the output never shows a transient code between nine and zero. Cascading between sections is done in the ripple mode, with the fourth output feeding the enable of the next section while its clock is held low, and that connection adds the carry delay of the first section to the second.
The reset is a high level on the reset line and it is asynchronous, so a reset pulse shorter than a clock period still clears the counter. That is convenient for a manual reset and it is a hazard for a noisy line, because a glitch on the reset input loses a count that no software can recover. A board that runs the counter from a mechanical contact should have a filter on the reset and on the clock, and the Schmitt trigger NAND in the same family is the part that usually provides it.
The input current of 1 microamp at 18 V and the noise margin of 1 V at 5 V are the interface figures. A counter driven from a slow analog front end needs a comparator or a Schmitt gate ahead of it, because a slow edge through the threshold band produces multiple counts. That is the most common field complaint about a counter built from this family, and it is a front end problem rather than a counter problem.
Where the plastic DIP is the right choice
A counter is usually part of a front panel or an instrument, and an instrument is repaired rather than replaced. The plastic DIP at 181.42 square millimetres and the 25 piece tube are the combination that keeps a service depot running. The SOIC at 59.4 square millimetres and the SOP at 79.56 are the surface mount options, and the SOIC tube is closed while the reel is live, so a small surface mount build has to take a cut reel.
The TSSOP at 32 square millimetres is the smallest body and the one with the least thermal margin, which matters little for a counter and matters if the outputs drive a display through a resistor network. The ceramic rows are active, which is useful for a wide temperature instrument that has to keep the same count logic in an extended range.
Cascading two sections into a two digit counter is the standard use. The carry output of the first section feeds the enable of the second while the second clock is held low, and the second section then advances on the carry rather than on the clock. The delay through the first section is added to the second, so a two digit counter is slower than a one digit counter by the carry delay, and a four digit counter built from two packages is slower again. At 6 MHz typical there is room for several sections, and at 5 V the guaranteed clock is lower than the typical figure at 10 V.
The BCD rollover is the other detail that a binary counter does not have. After nine the counter returns to zero and raises the carry, so a display driven directly from the four outputs shows a decimal digit without a decoder. That is the reason this part appears next to a seven segment driver in so many instrument builds, and the reason the CD4520B binary version is not a substitute when a decimal readout is wanted.
What the documents do not publish
The page does not print a maximum clock frequency, a setup time for the enable input or a reset pulse width. Those are in the data sheet, and for a cascaded counter the enable setup time is what limits the chain length. The page also does not print the state table, which for a BCD counter is the definition of the part: ten states, then a carry, then zero.
Second source and long term availability
The CD4518B is second sourced under the same number and the pin out is standard across the 4000 series. The nearest alternative is a 74HC160 or a 74HC390, and both change the pin out and the carry behaviour, so a board change is needed. The pin to pin cross reference page sets out the checks, and the component shortage forecast page covers how a long lead counter is planned into a build.
What to send with an enquiry
Send the string, the body, whether the count is BCD or binary, the quantity and the date. Say which edge the sensor produces, because the clock and enable pins are interchangeable and the wiring decides the polarity. If the board is surface mount, confirm that a 2500 piece reel or a cut reel is acceptable, because the SOIC tube is closed. The material requirements planning page explains how a counter and its display driver are scheduled together.