Contact Us

CD4093BE

Brand: Texas Instruments
Texas Instruments CD4093BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4093BE — Power Management & Signal Chain | Superb Automation

CD4093BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4093BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4093BE: the quad two input NAND gate with Schmitt trigger inputs in a plastic DIP

The CD4093BE is the plastic dual in line entry for the CD4093B, four two input NAND gates whose inputs are Schmitt triggers, in a 14-lead body. The vendor page lists the device as ACTIVE with a drive of 6.8 mA in both directions, an 8 Mbps data rate, an input type marked Schmitt-Trigger and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD4093BE.

The Schmitt trigger is the whole reason this part exists. Each input switches at a different point on a rising edge and on a falling edge, so a slow or noisy signal is converted into one clean transition instead of a burst of them. The vendor quotes hysteresis of 0.9 V at a 5 V rail and 2.3 V at 10 V, states noise immunity greater than 50 per cent, and states that there is no limit on input rise and fall times. Those three sentences describe a part that can be driven from an RC network, a mechanical switch or a long cable without an external comparator.

The CD4093B rows as the addendum publishes them

Part classFour two input NAND gates, Schmitt trigger inputs
Vendor descriptor4-ch, 2-input NAND, Schmitt-Trigger input
Vendor statusACTIVE, catalogue rating
Data sheetSCHS097 or later revision, acquired from Harris Semiconductor
Package addendum date18 September 2026
Supply range3 V to 18 V, 20 V type rating in the headline
Output drive6.8 mA sink and source at 15 V
Data rate8 Mbps in the parametric table
Hysteresis at 5 V0.9 V typical
Hysteresis at 10 V2.3 V typical
Noise immunityGreater than 50 per cent of the rail
Input rise and fallNo limit, per the feature list
Input current1 microamp at 18 V over temperature, 100 nA at 25 degrees
Noise margin1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V
PDIP body14 leads, 181.42 square millimetres, 19.3 by 9.4 mm
PDIP rowsCD4093BE, CD4093BE.A and CD4093BEE4, 25 pieces, Active
SOIC tube rowCD4093BM, 50 pieces, Active
SOIC large reelCD4093BM96, 2500 pieces, Active
Obsolete SOIC rowCD4093BMT, blank quantity, Call TI
SOP reel rowCD4093BNSR, 2000 pieces, Active
TSSOP rowsCD4093BPW tube Obsolete, CD4093BPWR reel 2000 Active
Ceramic rowsCD4093BF and CD4093BF3A, 25 pieces, Active

The surface mount side has two live reels and one dead small reel. A customer who needs two hundred pieces for a pilot cannot buy the 250 piece small reel anymore, because that row is closed. The options are a partial 2500 piece reel, the 2000 piece SOP reel, the TSSOP reel, or the 50 piece tube for a bench build. That is the same pattern as the rest of the band and the same trap for a buyer who assumes a small reel still exists.

What the Schmitt trigger does to the numbers

Hysteresis of 0.9 V at 5 V is eighteen per cent of the rail, and 2.3 V at 10 V is twenty three per cent. Those windows are what turn a slow edge into a single transition. A normal CMOS gate has a threshold band of about 1.5 V to 3.5 V at 5 V and will oscillate for the whole time a signal spends crossing it; this part has a narrower band and a defined direction, so it crosses once. The vendor's statement that noise immunity is greater than 50 per cent of the rail is the same property described from the other side.

The feature list also says there is no limit on input rise and fall times, which is a strong claim and it is the one that makes the part useful on a mechanical switch. A switch that bounces for a millisecond produces one output transition per bounce with an ordinary gate; with this part it produces one transition per crossing of the hysteresis window, and the window is wide enough that most of the bounce is ignored. The page does not quote the propagation delay, and the data sheet table is a scan in the document set we hold, so the delay figure is not quoted on this page rather than guessed.

The supply current and the input current follow the family. The input current of 1 microamp at 18 V is what a high value pull up has to supply, and the noise margin of 1 V at 5 V is quoted over the full temperature range. A customer who drives the input from a 1 megohm thermistor divider should check that the 1 microamp leakage does not move the trip point further than the hysteresis window allows.

Where the Schmitt input earns its place

The four gates cover the four jobs that always appear on a control board: a reset debounce, a switch input, an oscillator built from one gate and an RC, and a receiver for a slow or noisy line. The vendor application list names wave and pulse shapers, high noise environment systems, monostable and astable multivibrators and NAND logic, which is the same list in the vendor's words.

The plastic DIP is 181.42 square millimetres against 51.9 for the SOIC, 79.56 for the SOP and 32 for the TSSOP. For a bench instrument or a board that is repaired in the field, the DIP and its 25 piece tube are the practical choice, because a socket and a spare tube keep the equipment running for a decade. For a sealed module, the SOIC at 51.9 square millimetres is the body that fits without a pitch change on the assembly line.

What the documents do not publish

The product page does not print a propagation delay, a supply current, a maximum input frequency or a hysteresis figure at 15 V. It prints hysteresis at 5 V and 10 V and stops. The data sheet carries the rest, and in our copy the electrical tables are images, so the numbers have to be read from the printed page rather than extracted. The page states that limitation instead of filling the gap with a family typical.

The astable configuration is the other common use. One gate, one resistor and one capacitor make an oscillator, and because the input has hysteresis the circuit starts reliably and does not sit at a bias point where a plain inverter would stall. The vendor lists astable multivibrators among the applications, and the same document shows the monostable form for a one shot. Both circuits depend on the hysteresis window, so both change when the part is substituted for a gate without one.

The tape and the package outline are in the same document set and they are what an assembly engineer asks for first. The 330 mm reel fits the standard feeder, the 16.4 mm tape width is the same as the rest of the 14-lead SOIC family, and the pocket depth of 2.1 mm clears the 1.75 mm body height. A reel that does not fit the feeder is a line stop on the first day of production, and it is the kind of detail that a part number page should not leave to a phone call.

The board side is simpler. At 1.27 mm pitch the SOIC can be placed and inspected with the same stencil and the same optical check as the rest of the 4000 series parts on the board, so a mixed board does not need a second process. That is the practical argument for staying with this body when the area budget allows it.

Second source and long term availability

The CD4093B is second sourced under the same number by several vendors and the 14-lead pin out is standard. The nearest alternative is a 74HC132, which has a narrower hysteresis window and a much faster edge, so a debounce network built for the 4000 series part will behave differently. The how to verify a drop in replacement page shows the bench checks, and the safety stock planning page covers how much to hold when only the reels remain.

What to send with an enquiry

Send the string, the body, the quantity and the date. Say what the input is driven from, because a switch, an RC network and a cable each need a different check on the hysteresis window. If the board is through hole, the tube is 25 pieces. If the board is reflow, the 2500 piece reel or the SOP reel are the live formats and the small reel is closed. The BOM scrubbing page explains how the packing is matched to the build.