Contact Us

CD4060BE

Brand: Texas Instruments
Texas Instruments CD4060BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4060BE — Power Management & Signal Chain | Superb Automation

CD4060BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4060BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4060BE: the 14-stage counter and oscillator in the 16-lead plastic DIP

The CD4060BE is the plastic dual in line member of the CD4060B family, a 14-stage ripple carry binary counter that also contains the oscillator it needs. The vendor describes the part as a CMOS 14 stage ripple carry binary counter divider and oscillator and marks it ACTIVE. The parametric table gives a counter function, ten bits, standard CMOS input, push pull output and an operating range of minus 55 to plus 125 degrees.

The row reads Active, plastic DIP with 16 leads at 181.42 square millimetres, 25 pieces in a tube, RoHS yes with a nickel palladium gold lead finish, no moisture sensitivity level because a through-hole body is not reflow classified, minus 55 to plus 125 degrees and the marking CD4060BE. The same addendum carries CD4060BE.A and CD4060BEE4 at the same 25 piece tube, and the ceramic rows CD4060BF and CD4060BF3A sit beside them.

The CD4060BE row as the vendor addendum publishes it

Part class14 stage ripple carry binary counter with on-chip oscillator
Vendor descriptorCMOS 14-Stage Ripple-Carry Binary Counter/Divider and Oscillator
Vendor documentSCHS049C, revised October 2003, acquired from Harris Semiconductor
Counter stages14, with ten outputs brought out
Clock rate12 MHz at 15 V
OscillatorRC or crystal configuration, all active parts on chip
RC oscillator floor690 kHz minimum at 15 V
ResetCommon reset, fully static operation
Inputs and outputsBuffered, with a Schmitt trigger on the input pulse line
Quiescent currentTested at 20 V on every unit
Supply range3 V to 18 V, with 5 V, 10 V and 15 V parametric ratings
Input current1 microamp maximum at 18 V over temperature, 100 nA at 25 degrees
Package for this codePDIP (N), 16 leads, 181.42 square millimetres
Packing25 pieces in a tube
Lead finishNIPDAU
StatusActive, production
Part markingCD4060BE
SOIC tube rowCD4060BM, 40 pieces in a tube
SOIC reel rowCD4060BM96, 2500 pieces
NRND SOP rowCD4060BNSR, 2000 pieces, not recommended for new builds
TSSOP reel rowCD4060BPWR, 2000 pieces, marking CM060B
Obsolete rowsCD4060BMT and CD4060BPW, quantity blank, Call TI

One part instead of a counter and an oscillator

Fourteen binary stages in one body cover division ratios from two up to sixteen thousand three hundred and eighty four, and the oscillator that clocks them is inside the same package. That combination removes a separate oscillator package, a clock net and the propagation delay between the two, which is why the part survives in long interval timers, blinking indicators, watchdog chains and simple tone generators.

The division arithmetic is worth writing down before the footprint is committed. Fourteen stages give ratios up to sixteen thousand three hundred and eighty four, and the outputs that are brought out are the upper ten, so the ratios a board can use directly start at sixteen and end at the full chain. A timer that needs a ratio of ten cannot be built from one output; it needs feedback logic or a second counter, and that is a board level decision rather than a part level one. A tone generator that needs a ratio of two hundred and fifty six takes the eighth output and nothing else.

The ten outputs that are brought out are not all fourteen. The lower stages are consumed internally to reach the divider ratios, so a board that needs a divide by eight takes an output that exists rather than a lower stage that does not. That is the single most common misreading of the pinout, and it is worth checking the output list before the footprint is committed.

Twelve megahertz at 15 V and what it means at 5 V

The 12 MHz figure belongs to a 15 V supply. At 5 V the same part runs at a fraction of that, and the vendor does not print a 5 V value in the text of this document; the 2003 revision is a scan, so the switching tables are images. A timer that needs a fast clock at 5 V should not be built on this part without a bench measurement, and a timer that needs accuracy rather than speed should be built around the crystal configuration rather than the RC one.

The RC oscillator floor of 690 kHz minimum at 15 V is the other figure worth reading carefully. It is a minimum, which means the oscillator will run at least that fast at 15 V, not that it will not run slower. A low frequency RC timer built from this part at 5 V works, and its accuracy comes from the resistor and capacitor rather than from the part.

Reset, static operation and power-up behaviour

The counter is fully static, so it holds its state at any clock rate from zero upwards, and the common reset clears every stage. What the vendor does not promise is a defined power-up state: the reset pin has to be driven after the supply settles, or the counter can start from an unknown stage. On a timer that matters, because an unknown start state means an unknown first interval, and the usual cure is an RC network on the reset pin rather than a reliance on the internal circuit.

The Schmitt trigger on the input pulse line is what allows the part to count a slow edge. A phototransistor output, an RC shaped pulse or a switch contact all have edges that a plain CMOS input would count several times; the Schmitt input converts them into one transition per event, provided the noise is slower than the hysteresis.

Through-hole body and the divider chain

A 16-lead plastic DIP at 181.42 square millimetres is a large part for a counter, and the reason to take it is a board that is already through-hole or a socket that has to be swapable. A divider chain on a mains powered timer, built on a board with a transformer, a relay and a terminal block, is exactly the kind of product where this body still wins: the assembly is a wave solder process and the switch to surface mount would mean a second process for one part.

Where the board is surface mount, the family offers the SOIC tube at 40 pieces and the SOIC reel at 2500, plus a TSSOP reel at 2000. The SOP row CD4060BNSR is marked not recommended for new builds, which is the vendor's phrase for a part that ships but should not be chosen for a new build.

Availability and the counters that replace it

The CD4060B is still Active in three bodies, so this is not an obsolescence page. The interesting question is whether a modern alternative fits: a small microcontroller with an internal oscillator can replace the counter and the RC network, and it can also replace the trim pot that sets the interval. For a product with a microcontroller budget and a supply of programmable parts, that route is cheaper than a divider chain and a set of passive parts.

For a product that has no code and has to work for twenty years, the counter is the safer choice, and the component lead time solutions page covers how the three live bodies are scheduled. A customer who is moving off the SOP row because it is not recommended for new builds should read the obsolete part cross reference hub before choosing between the SOIC and TSSOP bodies.

What to send with an enquiry

Send the string, the supply rail, the division ratio needed, whether the oscillator is RC or crystal and the annual quantity. The division ratio decides which outputs have to be connected, and the oscillator choice decides whether the accuracy comes from the part or from the passive components. If the board is through-hole, say so, because the tube of 25 is one build for most instruments built in that quantity.