CD4052BPWR
Product Specifications
CD4052BPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4052BPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4052BPWR: the dual 4 channel multiplexer in the 16-lead TSSOP
The CD4052BPWR is the thin shrink small outline member of the CD4052B family on a 2000 piece reel. The part carries two independent 4 to 1 analogue switches on one die, sharing a pair of address lines, with on-chip decoding, a 3 V to 20 V digital control range, a 125 ohm typical on resistance at 15 V, an 18 picofarad on capacitance and a 25 MHz bandwidth. The vendor marks the family ACTIVE and describes it as a 20 V, 4 to 1, two channel analogue multiplexer with logic level conversion.
The row reads Active, TSSOP body with 16 leads at 32 square millimetres, 2000 pieces on a large tape and reel, RoHS yes, nickel palladium gold finish, moisture level 1 at 260 degrees with unlimited floor life, minus 55 to plus 125 degrees and the marking CM052B. The plain TSSOP tube row CD4052BPW is obsolete, and the older reel suffixes BPWRG3 and BPWRG4 are obsolete as well, so this row and its .A partner are the TSSOP formats that remain.
The CD4052BPWR row as the vendor addendum publishes it
| Part class | Dual 4 channel analogue multiplexer and demultiplexer |
| Vendor document | SCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B |
| Package for this code | TSSOP (PW), 16 leads, 32 square millimetres at 5 by 6.4 mm |
| Packing | 2000 pieces on a large tape and reel |
| Status | Active, production |
| RoHS | Yes |
| Lead finish | NIPDAU |
| Moisture level | Level 1 at 260 degrees, unlimited floor life |
| Part marking | CM052B |
| Sibling row | CD4052BPWR.A, same quantity |
| Obsolete TSSOP rows | CD4052BPW, CD4052BPWRG3, CD4052BPWRG4 |
| SOIC reel row | CD4052BM96, 2500 pieces, marking CD4052BM |
| SOP reel row | CD4052BNSR, 2000 pieces |
| PDIP row | CD4052BE, 25 pieces in a tube |
| Configuration | 4 to 1, two channels, shared address lines |
| Single supply | 3.3, 5, 12, 16 and 20 V |
| Dual supply | Plus or minus 2.5, 5 and 10 V |
| On resistance | 125 ohms typical at 15 V |
| Leakage | Plus or minus 10 pA typical at 15 V |
| Capacitance and bandwidth | 18 pF typical, 25 MHz |
| Current limit | 10 milliamps continuous per channel |
| ESD | 3000 V HBM, 2000 V CDM |
A 3.3 V rail is inside the specification on this body
The parametric table for the CD4052B lists single supply options of 3.3, 5, 12, 16 and 20 V, which is worth noting because the CD4053B in the same document lists 5, 12, 16 and 20 V and omits 3.3. A board running a 3.3 V rail therefore has a published single supply option on the 4052B and not on the 4053B, and that difference is easy to miss when the three parts share one document and one feature list.
The dual supply options are plus or minus 2.5, 5 and 10 V, which covers a plus or minus 5 V analogue front end from a plus or minus 5 V rail pair and a plus or minus 10 V swing for a wider signal. The digital control pins accept 3 V to 20 V regardless, so a 3.3 V microcontroller drives the address lines on a plus or minus 10 V part with no translator in between.
Where the thin body pays
Thirty two square millimetres against 59.4 for SOIC and 79.56 for SOP makes the TSSOP the only body that fits a dense analogue card. A board with four dual multiplexers takes 128 square millimetres in TSSOP against 238 in SOIC, and it also takes four 0.65 millimetre pitch placements instead of four 1.27 millimetre ones. For a card that is already carrying fine pitch converters and a microcontroller, that is not a new process capability.
The thinner body also shortens the thermal path to the board, which is not a factor at 12.5 milliwatts of channel dissipation but becomes one on a board with several multiplexers in a sealed enclosure. The part has no thermal pad and relies on the leads, so the copper under the body is the only heat spreader available and the note in the document on copper area is the one to follow.
Body choice inside the family
The same die is offered in four bodies: plastic DIP at 181.42 square millimetres, SOP at 79.56, SOIC at 59.4 and TSSOP at 32. The DIP is the only one that still ships in a 25 piece tube, and the other three are reel formats at 2000 or 2500 pieces. For a board that is revised anyway, the choice is board area against assembly process, and the TSSOP wins on area while the SOIC wins on inspection and rework.
Between the TSSOP and the SOIC the electrical behaviour is identical because the die is identical. What changes is the moisture sensitivity record, the reel quantity and the marking, and those three are what a purchasing system has to hold if the board is to be supplied from either row without a new drawing. A drawing that names only CM052B cannot be sourced from the SOIC row, because the marking is the only visible identifier on the reel, and a line that receives a CD4052BM marked part against a CM052B drawing will raise a documentation query however identical the die is. The reverse is also true: a board built with CM052B cannot be repaired from a reel of the SOIC row without an approved deviation, so the marking on the drawing has to match the row that will be purchased for the life of the product, and that is a purchasing decision as much as a documentation one, because the approved vendor list has to name the marking as well as the string.
Matching the pair and matching the board
The two channels of a CD4052B sit on one die, which gives them a shared temperature and a shared process. Their on resistance tracks within a few ohms, and that is the property that makes the part a differential switch rather than two single switches in one package. On a board with several parts, the same argument applies between packages only to the extent that they are at the same temperature, so a circuit that needs channel to channel matching across packages should keep them thermally together.
Common address lines mean the two channels always select the same input number. A circuit that needs independent selection takes two CD4051B parts or a CD4053B, which has three independent 2 to 1 switches with separate control pins.
Availability and the reel arithmetic
Two thousand pieces on a reel, with a tube format that no longer exists, puts the small quantity question in the same place as the rest of the family: a cut reel with a label. For a build of 400 boards with one multiplexer each, that is a fifth of a reel and a remnant of 1600 pieces to carry. The kitting service page explains how a remnant is labelled and carried so it can be issued to the next build without a bake cycle.
Where the part is used in a product with a ten year life, the reel row and the SOP row are the two that matter, and the safety stock planning page sets out how much of each to hold against a supplier lead time that moves. The one stop BOM sourcing page covers how the 4051B, 4052B and 4053B lines on one bill are ordered together so the three reels arrive in one shipment.
What to send with an enquiry
Send the rails, the number of channels in use, whether the pair is differential and the annual quantity. If the board runs 3.3 V only, say so, because that rules the 4053B out and leaves this part. If the drawing names the obsolete tube row, the reel is the live format and the quantity quoted has to be a reel quantity rather than a tube quantity.