Contact Us

CD4051BPWR

Brand: Texas Instruments
Texas Instruments CD4051BPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4051BPWR — Power Management & Signal Chain | Superb Automation

CD4051BPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4051BPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4051BPWR: the 8 to 1 multiplexer in the 16-lead TSSOP on a 2000 piece reel

The CD4051BPWR is the thin shrink small outline member of the CD4051B family, and it is the smallest body the family ships in. The die is the single 8 channel analogue multiplexer with on-chip address decoding, 3 V to 20 V digital control, a 125 ohm typical on resistance at 15 V, a 20 MHz bandwidth and a 10 milliamp channel limit. The vendor marks the family ACTIVE and describes it as a 20 V, 8 to 1, single channel analogue multiplexer.

The row reads Active, TSSOP body with 16 leads, 2000 pieces on a large tape and reel, RoHS yes, nickel palladium gold finish, moisture level 1 at 260 degrees with unlimited floor life, operating range minus 55 to plus 125 degrees and the marking CM051B. That marking is worth noting: it is not the part number. A board level trace that relies on reading the top mark will find CM051B and has to know that this is the TSSOP body of the 4051B family, while the SOIC body is marked CD4051BM.

The CD4051BPWR row as the vendor addendum publishes it

Part classSingle 8 channel analogue multiplexer and demultiplexer
Vendor documentSCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B
Package for this codeTSSOP (PW), 16 leads, 32 square millimetres at 5 by 6.4 mm
Packing2000 pieces on a large tape and reel
StatusActive, production
RoHSYes
Lead finishNIPDAU
Moisture levelLevel 1 at 260 degrees, unlimited floor life
Part markingCM051B
Sibling TSSOP rowCD4051BPWR.A, same quantity
Obsolete TSSOP rowCD4051BPW, quantity blank, Call TI
SOIC reel rowCD4051BM96, 2500 pieces, marking CD4051BM
SOP reel rowCD4051BNSR, 2000 pieces
PDIP rowCD4051BE, 25 pieces in a tube
Configuration8 to 1, one channel, bidirectional signal path
Digital range3 V to 20 V, independent of the analogue rails
Analogue rangeUp to 20 V peak to peak
Supply3 V to 20 V single, plus or minus 3 V to plus or minus 10 V dual
On resistance125 ohms typical at 15 V
LeakagePlus or minus 10 pA typical at 15 V
Bandwidth and capacitance20 MHz, 30 pF on capacitance typical
ESD3000 V HBM, 2000 V CDM

Thirty two square millimetres against fifty nine

The TSSOP body takes 32 square millimetres against 59.4 for the SOIC and 181.42 for the DIP, which is the reason a board that multiplexes eight channels eight times over picks it: eight multiplexers in TSSOP take 256 square millimetres, the same eight in SOIC take 475. On a card that has to fit eight sensor banks into a 3U enclosure, that saving is the difference between one board and two.

The cost is a 0.65 millimetre lead pitch and a thinner body. A 0.65 millimetre pitch needs a stencil aperture and a placement accuracy that a line running 1.27 millimetre parts does not always hold, and it needs a rework station that can lift a 16-lead body without bridging. The part is not fine pitch by modern standards, and it is fine pitch by the standards of the equipment that was building these boards in 2005.

Thermal behaviour on a low current part

The channel current limit is 10 milliamps and the on resistance is around 125 ohms at 15 V, so a channel carrying the full 10 milliamps dissipates 12.5 milliwatts in the switch. Sixteen channels cannot all carry that at once through one common pin, and the common pin is the real limit: the 10 milliamp figure belongs to any single channel, and the common path carries the sum during a scan. A multiplexer that scans eight 5 milliamp loads puts 40 milliamps through the common pin, which is four times the rating.

That arithmetic is why the part is used to switch signals rather than supplies. A sensor bias of 1 milliamp per channel keeps the common pin at 8 milliamps in the worst case, which is inside the rating with margin. A bank of eight LEDs is a different problem and belongs on a driver, not on a multiplexer.

The marking and the traceability question

Two bytes of marking, CM051B, carry the body and the family but not a date code in the string itself. On a board that has to be traced to a production lot, the reel label is the record, and a cut reel without its label breaks the trace. That is the practical reason a contract assembler wants the label kept with the remnant: the marking on the body cannot reconstruct which lot it came from.

A customer who is comparing stock from two suppliers should compare the reel labels rather than the top marks, because two reels from the same vendor lot can carry different date codes and the same marking. The date code management page explains how that comparison is done on an incoming inspection bench.

Replacement and availability

TI lists the TMUX4051 as a drop-in replacement with upgraded functionality, with 1.8 V compatible logic, a plus or minus 12 V analogue range and smaller packages, and the SN74LV4051A as pin for pin for 5 V or lower applications. For a board that runs the 4051B on plus or minus 10 V, neither is a straight swap on the analogue side, and the TSSOP body of the original is still the smallest way to keep the 20 V range.

The TSSOP tube row CD4051BPW is obsolete while the reel row is Active, so small quantities again come from a reel. The kitting service page covers how a 2000 piece reel is split across builds, and the one stop BOM sourcing page explains how a bill with several package variants of the same die is consolidated so the line is not setting up four different feeders for one function.

The three switches of the family in the same body

All three parts share one document and one feature list, and all three are offered in the 16-lead TSSOP body, so the choice inside a board is made on channel count and wiring rather than on package. The 4051B gives one 8 to 1 switch with three address lines, the 4052B gives two 4 to 1 switches with two address lines, and the 4053B gives three 2 to 1 switches with three independent control pins. A board that needs to select one of eight sources takes the 4051B because the decoding is on chip; a board that needs three independent two way selections takes the 4053B because each switch can be thrown separately.

The 4053B is also the member that omits 3.3 V from the published single supply list, so a 3.3 V rail board that needs three independent switches has to check the analogue path against a lower rail before committing. The 4051B and the 4052B both list 3.3 V in the parametric table, which is the one electrical difference between the three parts that a buyer can see without opening the document. A customer who has to hold one body on the shelf for all three functions can do so, since the pinout of the three parts differs only in which pins are channels and which are controls, and the 16-lead TSSOP footprint is common to all three rows, which is why a board can move between the three functions without a new stencil.

What to send with an enquiry

Send the analogue rails, the scan rate, the number of channels switched simultaneously and the annual quantity. The scan rate decides whether the 30 picofarad on capacitance is a problem, and the number of channels decides the common pin current. If the existing drawing names the obsolete tube row, say so, because the reel is the only live format and the quantity question changes with it.