CD4011BE
Product Specifications
CD4011BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4011BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4011BE: four 2-input NAND gates in the 14-lead plastic DIP
CD4011BE is the quad 2-input NAND of the CD4000B family, four independent gates with buffered inputs and outputs on a 3 V to 18 V CMOS process. The vendor document is SCHS021D revision D, which also covers the CD4012B and the CD4023B, and the descriptor on the product page reads four channels, two inputs per channel, 3 V to 18 V. The NAND function is the one that makes the rest of a CMOS logic set possible, and the 4011 is the package most often reached for when a board needs four independent 2-input terms in one body.
The addendum lists CD4011BE as Active in production, PDIP (N) with 14 leads, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, no moisture level for the through-hole body, minus 55 to plus 125 degrees, and the marking CD4011BE. The same document carries CD4011BM at 50 to a tube, CD4011BM96 at 2500 to a reel, CD4011BNSR at 2000 to a reel, CD4011BPWR at 2000 to a reel with the marking CM011B, and the obsolete rows CD4011BMT and CD4011BPW, so the family is complete across four bodies.
The CD4011BE row as the vendor addendum publishes it
| Part class | Quad 2-input NAND gate, buffered inputs and outputs |
| Vendor descriptor | Four channels, two inputs per channel, 3 V to 18 V |
| Vendor document | SCHS021D revision D, CD4011B, CD4012B and CD4023B |
| Supply range | 3 V to 18 V |
| Parametric ratings | 5 V, 10 V and 15 V tables |
| Propagation delay, vendor figure | 60 ns typical at 10 V into a 50 pF load |
| Output drive, parametric table | 6.8 mA sink and source |
| Data rate, parametric table | 8 Mbps |
| Input current, maximum | 1 microamp at 18 V over the full range, 100 nA at 18 V and 25 degrees |
| Quiescent current | Tested to maximum at 20 V on every unit |
| Noise margin | 1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V |
| Package for this code | PDIP (N), 14 leads |
| Packing | 25 pieces in a tube |
| Lead finish | NIPDAU |
| Moisture level | Not applicable for this package type |
| Operating range | Minus 55 to plus 125 degrees |
| Status | Active, production |
| Part marking | CD4011BE |
| Same string in the addendum | CD4011BE.A and CD4011BEE4, both 25 piece tube |
| SOIC member | CD4011BM 50 piece tube, CD4011BM96 2500 piece reel |
| SOP member | CD4011BNSR, 2000 piece reel |
| TSSOP member | CD4011BPWR, 2000 piece reel, marking CM011B |
| Obsolete rows | CD4011BMT and CD4011BPW, quantity blank, Call TI |
The NAND function at 60 ns and 6.8 mA
The propagation figure is 60 ns typical at 10 V into a 50 pF load, the drive is 6.8 mA in both directions, and the parametric table lists an 8 Mbps data rate, which is the same delay expressed another way. NAND gates in this family are buffered, so the output stage does not load the input stage and the delay is nearly independent of how many gates the output drives, up to the drive limit. That buffering is also why the part is not interchangeable with the older unbuffered A series in a timing critical circuit, where the unbuffered gate is faster into a small load and much slower into a large one.
Two uses of the gate dominate. The first is the set-reset latch that engineers build from two cross coupled NANDs, which is the standard way to debounce a switch or to hold a fault flag without a dedicated latch part. The second is the inverter: tying both inputs of one gate together gives a logic inverter with the same 60 ns delay, and a package of four gates gives four inverters or two latches or a mix of the two. A circuit that needs six inverters takes two packages, which is the point at which the CD4049UB hex inverter becomes the cheaper answer.
Noise, leakage and the pull-up arithmetic
The DC behaviour is the same family behaviour: 1 V of noise margin at 5 V, 2 V at 10 V and 2.5 V at 15 V over the full temperature range, an input current of 100 nA at 25 degrees and 1 microamp over the range, and a quiescent current that is tested to maximum at 20 V on every unit. The leakage number sets the pull resistor. A 1 megohm pull on an input holds 0.1 V at room temperature, which is a clean low, and 1 V at 125 degrees, which is still a low at a 5 V rail but eats the whole margin at 3.3 V. A 100 k pull holds 0.1 V at the top of the range and is the safe choice for an industrial board.
Because the inputs are buffered, the input capacitance is small and the input current is leakage rather than a bias current, which means a switch debounce network built around a 100 k resistor and a 100 nF capacitor settles in about 10 ms and holds its state with no further current. That is the reason the two NAND latch survives in circuits that could use a Schmitt trigger part: the latch costs one gate and one resistor per side, and it holds state without a clock.
Where the 4011 sits against the 4012 and the 4023
The document covers three NAND widths: four 2-input gates in the CD4011B, two 4-input gates in the CD4012B, and three 3-input gates in the CD4023B. The choice follows the same logic as the NOR family. Four independent 2-input terms take the 4011; a wide shallow function takes the 4012; a three-input function takes the 4023. All three carry the same 60 ns typical delay and the same 3 V to 18 V range in the vendor document.
The drive figure is where the two documents disagree in a way worth flagging. The CD4023B parametric table lists 1.5 mA sink and source, while the CD4011B table lists 6.8 mA, even though both appear in the same document and on the same process. A board that drives a load from a 4023 output should be checked against the 1.5 mA figure rather than against the 4011 number, and this page states the difference rather than averaging it.
Incoming checks for a NAND line
The function test for this part is a four row truth table per gate at the rail the board uses, which catches a gate with one dead input even when the other three work. The body marking distinguishes the plastic DIP from the SOIC and the TSSOP, and the obsolete TSSOP row CD4011BPW is a real risk on grey stock because it shares a marking with the active PWR row. The date code check follows the same rule as the rest of the family.
The pages behind those checks are the incoming inspection plan, date code management, and the vendor consolidation route when a bill of materials carries three logic families from three suppliers and one of them is being reduced.
Questions that come up on the 4011
Whether two gates can be paralleled for more drive. They can be paralleled in logic terms, but the two gates do not switch at exactly the same instant, so the sharing is uneven and the practice is not recommended for a load near the 6.8 mA limit.
Whether the part can drive a small relay through a transistor. It can, with a 1 k base resistor, because the 6.8 mA is more than the base current a small bipolar needs, and the 60 ns delay is irrelevant to a mechanical load.
Whether the DIP body is still available in volume. The addendum lists it as Active at 25 to a tube, so it is available, but the volume formats are the SOIC reel and the TSSOP reel, and a production forecast should name one of those.
Whether a 74HC00 can replace the part at 5 V. The function and the pinout match at 5 V, the HC part is faster and has a lower drive, and the swap needs a check of the load and of the input thresholds rather than a straight substitution.