CD40106BCMX
Product Specifications
CD40106BCMX
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD40106BCMX from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD40106BCMX: the hex Schmitt inverter and the suffix the addendum does not publish
The CD40106BCMX is a catalogue string for the CD40106B, six inverting Schmitt triggers in a 14-lead body, with a CMX suffix. The vendor addendum dated 18 September 2026 publishes fifteen rows for this device and not one of them carries the CMX suffix. The rows that do exist are the plastic DIP CD40106BE, the small outline tube CD40106BM, the small outline reel CD40106BM96, the small outline small reel CD40106BMT, the SOP reel CD40106BNSR, the thin shrink tube CD40106BPW and the thin shrink reel CD40106BPWR, plus the ceramic rows.
That gap matters because a suffix on a drawing is not a description, it is an order code. A buyer who sends CD40106BCMX to a distributor is sending a string the vendor does not list, and the answer will be a substitute chosen by the distributor rather than by the board. The two surface mount reels that do exist are the SOIC at 2500 pieces and the SOP at 2000 pieces, and either one can be named in place of the CMX string after the footprint is checked.
The CD40106B rows as the addendum publishes them
| Part class | Six inverting Schmitt triggers |
| Vendor descriptor | 6-ch Schmitt trigger inverter, 3 V to 18 V |
| Vendor status | ACTIVE, catalogue rating |
| Data sheet | SCHS097 or later revision, acquired from Harris Semiconductor |
| Package addendum date | 18 September 2026 |
| CMX row | Not published anywhere in the addendum |
| Supply range | 3 V to 18 V, 20 V type rating in the headline |
| Output drive | 2.4 mA sink and source |
| Supply current | 120 microamps maximum |
| Hysteresis at 5 V | 0.9 V typical |
| Hysteresis at 10 V | 2.3 V typical |
| Hysteresis at 15 V | 3.5 V typical |
| Noise immunity | Greater than 50 per cent of the rail |
| Input rise and fall | No limit, per the feature list |
| Supply current during slow ramp | Low VDD and VSS current, per the feature list |
| SOIC tube row | CD40106BM, 50 pieces, Active |
| SOIC reel row | CD40106BM96, 2500 pieces, Active |
| SOIC small reel | CD40106BMT, Obsolete, blank quantity, Call TI |
| SOP reel row | CD40106BNSR, 2000 pieces, Active |
| TSSOP rows | CD40106BPW tube Obsolete, CD40106BPWR reel 2000 Active |
| PDIP row | CD40106BE, 25 pieces in a tube, Active |
| Ceramic rows | CD40106BF and CD40106BF3A, 25 pieces, Active |
The marking is the second surprise. The SOIC rows are marked CD40106BM, the SOP rows are marked CD40106B, and the TSSOP rows are marked CM0106B. A first article inspection that expects the orderable string on the body will fail every TSSOP reel until the marking column is read. The page prints the marking values because they are the only way to tell a correct part from a relabelled one at goods inwards.
What the Schmitt trigger does to the numbers
The hysteresis is 0.9 V at 5 V, 2.3 V at 10 V and 3.5 V at 15 V, and it is the widest hysteresis in this group of devices at the higher rails. The vendor states noise immunity greater than 50 per cent of the rail and no limit on input rise and fall times, and adds a low supply current during a slow input ramp, which is the figure that separates this part from a plain inverter: a plain inverter draws crowbar current for the whole time the input crosses the threshold band, and this one crosses the band once and stops.
The supply current is 120 microamps maximum, the lowest in this group, and the drive is 2.4 mA in both directions. That drive is enough for a CMOS input and for a small light emitting diode at a milliamp, and it is not enough for a relay or a lamp. The operating range is minus 55 to plus 125 degrees, and the hysteresis figures are quoted over that range rather than at room temperature only.
The 20 V headline, the 18 V operating limit and the 15 V top of the parametric table are three different numbers again. A board at 18 V has DC limits but no guaranteed switching limit, and a board at 20 V is outside the recommended range even though the headline names it.
Where the small outline body fits
The SOIC is 51.9 square millimetres against 181.42 for the plastic DIP, 79.56 for the SOP and 32 for the TSSOP. For a board that has to receive a slow signal from a cable or a switch, the SOIC is the body that combines a coarse pitch with a small area, and the 2500 piece reel is the format a pick and place line expects. The 50 piece tube covers a prototype and the small reel is closed, so a build of a few hundred pieces takes a cut reel.
The thermal impedance of the SOIC is 86 degrees per watt in the family document, 80 for the plastic DIP and 113 for the TSSOP. At 120 microamps of supply current the number is academic in normal operation, and in a fault it is the TSSOP that heats first. The 2.4 mA drive also limits the fault current, which is one reason this part survives a miswired input better than a buffered driver.
The SOP reel is the row to name when a smaller body is needed and the TSSOP is too fine for the line. At 79.56 square millimetres the SOP sits between the SOIC at 51.9 and the plastic DIP at 181.42, and it carries a 2000 piece reel with the same level 1 moisture rating. A board that was laid out for the SOP can stay there, and a board that needs the smallest area takes the TSSOP at 32 square millimetres on a 0.65 mm pitch.
The ceramic rows are active and that is worth knowing for a customer who has to keep an extended temperature instrument alive. The BF and BF3A rows are 25 pieces in a tube with a tin lead finish, and the marking differs from the plastic rows. A defence or aerospace customer who names the plastic string and expects the ceramic part will get the wrong body, and the addendum is the only place where the two are separated, which is why the string on the drawing has to match a published row exactly before a purchase order is raised and before a second source is quoted against it by a distributor.
What the documents do not publish
No propagation delay, no maximum input frequency and no output capacitance appear on the page. The data sheet carries the switching table, and in our copy the electrical tables are images, so the delay has to be read from the printed page rather than extracted. The page states that limitation rather than quoting a family typical from a different device.
Second source and long term availability
The CD40106B is second sourced under the same number and the SOIC reel is live. The substitution to watch is a 74HC14, which has a narrower hysteresis window and a much faster edge, so a debounce that relied on the wide window will pass a bounce it used to reject. The how to verify a drop in replacement page sets out the checks, and the component obsolescence management page covers what to do with a string that has no matching row.
What to send with an enquiry
Send the string, and if the string ends in CMX, send the footprint and the packing you actually need, because the CMX row does not exist and the substitute has to be chosen deliberately. Send the body, the quantity and the date. If the input is a switch or a cable, say so, because the hysteresis window and the pull up value are checked together. The BOM scrubbing page explains how a string with no matching row is resolved before a quote is issued.