TPS259470ARPWR
Product Specifications
TPS259470ARPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS259470ARPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS259470ARPWR 5.5 A eFuse with back-to-back FETs and active current limiting
The TPS259470ARPWR is a 2.7 V to 23 V eFuse in a 2 mm by 2 mm ten pin QFN. Two FETs sit back to back between IN and OUT, so the part can block current in both directions and behave like an ideal diode without any external pass device. Around that switch the vendor has put an adjustable undervoltage lockout, an adjustable overvoltage lockout, an adjustable current limit with an analog current monitor, a blanking timer and a fault flag.
The suffix on this string carries the behaviour. The A in TPS259470A is the auto-retry member, so a fault that clears lets the part start again on its own after a fixed internal delay. The L member of the same table stays latched off until the input is cycled or the enable pin is toggled. On a board that is expected to recover unattended, the A string is the one to order, and on a board where a latched fault is the safer outcome, the L string is the one to order. The two parts share one body, one pinout and one reel size, which is why the last letter is easy to lose on a purchase order.
Key parameters taken from the TPS25947 document
| Input range | 2.7 V to 23 V operating, with 28 V absolute maximum on the input |
| Negative withstand | The part survives minus 15 V on the input without a series diode |
| On resistance | 28.3 milliohm typical for the back-to-back pair, measured from IN to OUT |
| Current limit window | Adjustable from 0.5 A to 6 A, with ten per cent accuracy above 1 A |
| Limit setting | One resistor on the ILM pin, printed as 3334 divided by the limit in amps |
| Published limit points | 6.65 k for 0.575 A, 3.32 k for 1.15 A, 1.65 k for 2.2 A, 750 ohm for 4.84 A, 549 ohm for 6.6 A |
| Fast trip | 500 ns typical on a hard short, with the threshold tied to twice the set limit |
| Overvoltage lockout | Adjustable with a resistor divider, 1.2 microsecond typical response |
| Undervoltage | Internal threshold 2.53 V rising and 2.42 V falling typical, adjustable upward with the same divider |
| Blanking timer | Set by a capacitor on ITIMER, charged by a 1.8 microamp pull-up and discharged during an overcurrent event |
| Current monitor | Analog output on the same ILM pin, 182 microamp per amp typical, six per cent accuracy above an amp |
| Thermal shutdown | 154 degrees junction rising with 10 degrees of hysteresis, then a fixed retry delay on the A member |
| Package | VQFN-HR RPW, ten pins, 2 mm by 2 mm, 0.45 mm pitch |
| Carrier | 3000 pieces on a large reel, moisture level 2 at 260 degrees with a one year floor life |
| Marking and grade | 2ADH on the A row, rated minus 40 to plus 125 degrees junction |
| Recognition | UL 2367 file E339631 and IEC 62368-1 CB certification |
Every row above comes from the vendor document rather than from a distributor summary. Where the document prints a window, the window is the figure to use for a production limit, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The current limit resistor is the single part that decides whether a board survives a fault. The document prints one equation, 3334 divided by the wanted limit in amps, and then prints five measured points, which do not fall exactly on the line of that equation. The 549 ohm point is given as 6.6 A while the equation returns 6.07 A, so a limit that matters to a safety test has to be taken from the measured table or from a bench measurement on the assembly, not from the equation alone. The same table also warns that leaving the ILM pin open sets the limit to nearly zero, which turns a small load into a permanent current limit event, and that shorting the ILM pin to ground is detected as a fault and switches the part off.
During a current limit event the part folds back, so the limit below roughly 0.5 V of output is lower than the steady state limit. That behaviour is what keeps a shorted load from cooking the die, but it also means a board that starts into a large capacitance with a heavy load attached can sit in foldback far longer than a bench test with a resistive load suggests. The blanking timer is the tool that separates the two cases. A capacitor on ITIMER holds the part in normal conduction for the time it takes the 1.8 microamp pull-down to move the timer voltage by its threshold, so a load that draws a short pulse of twice the limit passes through without a shutdown, while a load that stays above the limit long enough trips the timer.
Inrush is the other place where the numbers are not intuitive. With the dVdt pin left open the output rises at about 12 V per millisecond from a 2.7 V input, 28 V per millisecond from 12 V and 45 V per millisecond from 23 V. Adding 1800 pF slows that to 0.87, 1.09 and 1.25 V per millisecond, and 3300 pF slows it to 0.5, 0.61 and 0.71 V per millisecond. A 100 microfarad load on a 12 V rail therefore pulls about 2.8 A for the first few milliseconds with the pin open and about 0.1 A with the larger capacitor fitted, and the difference decides whether the upstream supply droops enough to reset the rest of the board.
The reverse blocking loop is not a simple switch. The part regulates the forward drop across the two FETs in a closed loop so that the DC reverse current is essentially zero, and a separate comparator with a faster path handles a transient reversal. Recovery after a reversal waits for the forward drop to pass a higher threshold than the one that tripped the block, which is deliberate hysteresis so that supply ripple cannot chatter the switch. In a power MUX this is the behaviour that decides how much the bus dips when one of two supplies collapses.
The AUXOFF pin and the FLT pin are the two digital handles on this member. AUXOFF is asserted once the input is valid and the inrush sequence has finished, so it can be wired to the enable of the second eFuse in a priority MUX. FLT is open drain and pulls low on a fault. A board that reads FLT without reading the timer state can misread a blanking event as a hard failure, since the flag follows the fault logic rather than the current level.
- Which suffix is on the order, A for auto-retry or L for latch-off, because the reel and the marking do not make the difference visible.
- The current limit resistor tolerance, since a one per cent part is needed to hold a limit that a safety test measures.
- The blanking capacitor, because the timer decides whether a legitimate peak load trips the part.
- The dVdt capacitor against the real load capacitance, not against the capacitance on the bench.
- The overvoltage divider, since the lockout threshold moves with it and a 24 V adapter sits close to the top of the range.
- The reel and the moisture level, because the level 2 rating carries a one year floor life and a bake decision after that.
Which projects this part fits
The vendor lists power MUX and ORing, adapter input protection, USB PD protection in PCs, notebooks, monitors and docks, server motherboards and add-on cards, enterprise storage such as RAID, HBA, SAN and eSSD, and patient monitors. The common thread is a rail that is fed from more than one source or plugged in while live, where the board has to survive a hot plug, a reversed adapter and a shorted load without a fuse that has to be replaced.
Questions that come up before a purchase order is released
What is the difference between the TPS259470A and the TPS259470L?
The A member retries automatically after a fault clears and after the retry delay expires. The L member stays off until the input is cycled or the enable pin is toggled. Both are the same die, body and reel.
How is this different from the TPS259474A?
The 474A replaces active current limiting with a circuit breaker and adds a power good output with an adjustable threshold. The 470A keeps active current limiting and carries an auxiliary channel control pin and a fault flag instead.
Does the part need an external TVS on the input?
The input is rated to 28 V absolute maximum and survives minus 15 V, so a 24 V adapter with normal transients is covered. A line that sees inductive switching spikes above 28 V still needs a clamp in front of the part.
What happens if the current limit resistor is left open?
The limit falls to nearly zero and the part enters current limit with the smallest load. That condition is listed in the document as a warning, and it is one of the single point failures the part is tested for.
Can the part block reverse current while it is disabled?
Yes. The two FETs are back to back and the body diode path is broken in both states, which is why the part is used in ORing where one supply can sit at zero while the other is live.
Why does 28 milliohm matter at 5 A?
At 5 A the pair dissipates about 0.7 W. A part with twice that resistance dissipates twice the heat in the same 2 mm body, which is the difference between a board that runs cool and a board that needs copper area under the part.
How SUPERB handles this line
These parts are bought in reel quantities and the differences between members sit in one letter of the string, so the purchasing risk is a wrong suffix rather than a wrong family. Our power management cross reference carries the comparison against the devices this part replaces, and our pin to pin cross reference covers the checks a substitute has to pass before it goes on a board. Where a programme needs the eFuse, the passives around it and the connector in one shipment, our kitting service is the route we quote.