Contact Us

TPS259531DSGR

Brand: Texas Instruments
Texas Instruments TPS259531DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS259531DSGR — Power Management & Signal Chain | Superb Automation

TPS259531DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS259531DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS259531DSGR 4 A eFuse with a 5.7 V output clamp and auto-retry

The TPS259531DSGR is a 4 A eFuse from the TPS2595 family, rated from 2.7 V to 18 V with a typical 34 milliohm pass path in an eight pin WSON of 2 mm by 2 mm. It carries an adjustable current limit with an analog current monitor, an adjustable slew rate, an overvoltage clamp and a thermal shutdown, and it does all of that with three external parts: a resistor on the limit pin, a capacitor on the slew pin and a capacitor on the output.

The string decodes into three choices. The 31 is the 5.7 V clamp member with auto-retry, the 5 in that position separates the 3.8 V, 5.7 V and 13.7 V clamp levels, and the trailing letters set the package and the carrier. A buyer who orders this part for a 12 V rail has ordered the wrong clamp level, because 5.7 V is the level for a 5 V rail that may be plugged with a 12 V adapter. That mistake does not stop the board from working on the bench with a 5 V source; it shows up only when the wrong adapter arrives.

Key parameters taken from the TPS2595 document

Input range2.7 V to 18 V operating, 20 V absolute maximum
On resistance34 milliohm typical at 25 degrees, 47 milliohm over the full junction range, 53 milliohm below 4 V of input
Current limit window0.5 A to 4 A, 7.5 per cent accuracy
Limit settingOne resistor on the ILM pin, printed as 2000 divided by the limit in amps minus 0.04
Published limit points487 ohm for 4.17 A, 1.78 k for 1.17 A, 4.42 k for 0.49 A
Overvoltage clamp5.7 V typical threshold, output held near 5.45 V, 5 microsecond response at 4 A
Current monitor276 microamp per amp typical on the ILM pin
Current limit response250 microsecond typical to reach the limit, 5 microsecond short circuit response
Slew rate16.3 V per millisecond at 3.3 V, 21.9 at 5 V and 38.2 at 12 V with the pin open, 10 to 12.4 V per millisecond with 3300 pF
Thermal shutdown157 degrees junction rising with 5 degrees of hysteresis, auto-retry interval 93 milliseconds on this member
Single point failureTested to IEC 62368-1 with the limit pin open and shorted, and the pin fault is detected rather than ignored
PackageWSON DSG, eight pins, 2 mm by 2 mm
Carrier3000 pieces on a large reel, 250 on a small reel for the T suffix
Marking and gradeES31, moisture level 2 at 260 degrees with a one year floor life, minus 40 to plus 125 degrees
RecognitionUL 2367 file E169910 and IEC 62368-1 certification

The table is taken from the vendor document. The single point failure row is worth reading twice, because it describes behaviour that a safety report will ask about: with the limit resistor open the part does not pretend the limit is high, and with the pin shorted the fault is detected.

Where the numbers matter in a real build

The limit equation for this family is not proportional. It is printed as 2000 divided by the limit in amps minus 0.04, so a 4 A target lands near 487 ohm and a 0.5 A target near 4.42 k, and the offset term matters at the low end far more than at the high end. That is why the document prints three measured points rather than one equation, and why a resistor chosen from the equation alone can miss the target by a few per cent at low currents.

The clamp is the reason this member exists in a 5 V product. When the input passes 5.7 V the part stops the output from following, and the pass FET absorbs the difference while the event lasts. The output sits near 5.45 V, which is high enough for the downstream converter to keep running and low enough to stay inside its input window. Because the FET is absorbing the drop, a long overvoltage event heats the die, and the thermal shutdown at 157 degrees ends the event. On this member the part then waits 93 milliseconds and tries again, which produces a hiccup pattern for as long as the overvoltage is present.

The 4 A rating and the 34 milliohm path are tied together. At 4 A the part dissipates about 0.54 W, and the 2 mm body with its exposed pad needs the pad soldered to a real copper area to hold that. The document also prints a higher resistance below 4 V of input, up to 53 milliohm over temperature, which is a 0.85 W figure at the same current. A 3.3 V rail therefore runs hotter than a 5 V rail at the same load, and a product that has to work from a 3.3 V supply with a 4 A load needs the thermal check done at that corner.

Slew rate is set by one capacitor and the range is wide. With the pin open the output rises at 16 V per millisecond from 3.3 V and 38 V per millisecond from 12 V, so a 100 microfarad load pulls a very large inrush. With 3300 pF the ramp falls to about 10 to 12 V per millisecond, which is a controlled start rather than a bang. The capacitor value has to be checked against the load capacitance and the current limit together, because a ramp that is too slow leaves the part in the linear region long enough to hit the thermal limit, and a ramp that is too fast trips the upstream supply.

The monitor output is a current, not a voltage. At 276 microamp per amp a 4 A load produces about 1.1 mA, which across a 1 k resistor is 1.1 V. A board that reads this pin with a high impedance input sees a voltage that depends on the resistor, so the resistor belongs in the tolerance stack with the reference of whatever reads it.

  • The clamp level, 3.8 V, 5.7 V or 13.7 V, because the wrong level passes a bench test and fails on a real adapter.
  • The limit resistor at the low end, where the offset in the equation is a large fraction of the target.
  • The slew capacitor against the real load capacitance, not against the capacitance on the bench.
  • The copper under the exposed pad, since the part has no lead frame to spread heat.
  • The reel suffix, because 3000 pieces and 250 pieces ship under strings that differ by one letter.
  • The moisture level, which carries a one year floor life and a bake decision after that.

Which projects this part fits

The vendor lists hot swap and hot plug, adapter powered systems, multifunction printers, SSDs and hard disks, industrial systems, white goods, set top boxes and digital televisions. The 5.7 V clamp with a 4 A limit is the classic shape for a box that runs from a 5 V adapter and has to survive a 12 V adapter being plugged in by mistake.

Questions that come up before a purchase order is released

What is the difference between the TPS259531 and the TPS259541?

The clamp level. The 531 clamps at 5.7 V for a 5 V rail and the 541 clamps at 13.7 V for a 12 V rail. Both are auto-retry members with an active high enable and no quick output discharge.

Does the part limit current or clamp voltage?

Both. It limits the current into an overload and it clamps the output when the input goes above the clamp threshold. The two paths are separate and both are in the same body.

What happens on a hard short?

The short circuit path responds in about 5 microseconds, far faster than the 250 microsecond current limit response, and the part then follows the retry behaviour of its member.

Is a fuse still needed in front of the part?

The part is recognised to UL 2367 and certified to IEC 62368-1, and it is tested with the limit pin open and shorted, so a fuse is not required for the single point failure argument. Local practice may still ask for one.

Why is the resistance higher at 3.3 V?

The document prints 34 milliohm typical at 25 degrees and 53 milliohm below 4 V of input over the full temperature range. The gate drive has less headroom at the lower input, and the thermal check has to use the higher figure.

How SUPERB handles this line

This family is bought in millions of pieces a year across the industry, so the differences between members are small and the cost of a wrong member is large. Our power management cross reference lists the replacements for this line, our pin to pin cross reference covers the bodies that share a footprint, and our safety stock planning page covers how we hold a buffer on the members that move fastest.