Contact Us

TPS2812DR

Brand: Texas Instruments
Texas Instruments TPS2812DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2812DR — Power Management & Signal Chain | Superb Automation

TPS2812DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2812DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2812DR dual inverting high speed MOSFET driver in SOIC

The TPS2812DR is a dual channel high speed MOSFET driver with inverting inputs, in an eight pin SOIC. It delivers 2 A peak into a capacitive gate, switches in 25 nanoseconds at a 1 nF load with 40 nanoseconds of propagation delay, and runs from a 4 V to 14 V supply. An internal regulator extends the input range to 40 V on this member, and its output can be used to power other circuitry on the same card as long as the package dissipation allows it.

Parts of this age stay in production because they solve a specific interface problem: a controller that swings a few volts has to drive a gate that wants amps, on a board where the switching node is next to sensitive analog circuitry. The TPS28xx family keeps the shoot through current low and the supply current small, which is why it turns up in telecom line cards, motor drives and power supplies that were laid out around it and are still shipping.

Key parameters taken from the TPS2811 to TPS2815 document

ChannelsTwo, with independent inputs and outputs
LogicDual inverting on this member, dual noninverting on the TPS2813, one of each on the TPS2811
Peak output current2 A at a 14 V supply, into a highly capacitive load
Rise and fall25 nanoseconds maximum with a 1 nF load at 14 V
Propagation delay40 nanoseconds maximum, same conditions
Supply range4 V to 14 V direct, extended to 40 V through the internal regulator on this member
RegulatorREG_IN and REG_OUT pins, with REG_OUT able to supply other circuits within the package dissipation limit
Regulator bypassWhen the regulator is not needed, REG_IN and REG_OUT may be left open or tied to VCC or ground
Shoot throughHeld low by the output stage, which is the reason the supply current stays small at high frequency
TemperatureMinus 40 to plus 125 degrees ambient, operating range
PackageSOIC, eight pins, D suffix; the same die is offered in PDIP and TSSOP
Order code noteD is the SOIC body, R is the reel tape

The document numbers in this table come from the first page of the vendor document. The electrical characteristics section prints the same figures with test conditions attached, and those conditions are what a production test has to reproduce.

Where the numbers matter in a real build

Twenty five nanoseconds into a 1 nF gate is a peak current of about 2 A, and the loop that carries that current is the part of the board that decides whether the driver survives. A gate loop with 20 nanohenry of inductance and 2 A switching in 25 nanoseconds produces several volts of ground bounce, which is enough to false trigger the second channel on the same package. The document's placement guidance is short, and most of the practical work is in keeping the source connection of each channel separate down to the ground pin.

The regulator is the second practical point. On a 24 V rail the internal regulator drops the supply to a value the output stage can use, and the difference is dissipated inside the package. Two channels switching at 100 kHz with a 2 nF load each will heat the part through that path before the output stage does. A card that uses the regulator output to power a small logic section adds to the same budget, and the package dissipation limit is the ceiling for both.

The third point is the logic polarity. The TPS2812 inverts, the TPS2813 does not, and the difference is one character in the order code with no visible marking difference. A build that substitutes one for the other produces a board that runs with the gate signal inverted, which on a half bridge is a shoot through event rather than a subtle fault.

  • The logic polarity, inverting here against noninverting on the TPS2813, because the marking does not show it.
  • The gate loop inductance, since 2 A in 25 nanoseconds turns a few centimetres of trace into a problem.
  • The package dissipation when the internal regulator is loaded, because the regulator and the output stage share one budget.
  • The decoupling capacitor placement at VCC, which is the other half of the same loop.
  • The ambient temperature inside the enclosure, since the 125 degree rating is measured at the part and not at the cabinet door.
  • The reel and the date code on a part this old, because stock that has sat in a warehouse for years still reflows but the solderability record matters.

Which projects this part fits

The document describes the family as an industry standard driver replacement. In practice the parts appear in switched mode supplies, motor drives, telecom line cards, lamp ballasts and any board where a controller output has to drive a power MOSFET gate with fast edges and a small supply current. The inverting version suits a controller whose output idles high.

Questions that come up before a purchase order is released

What is the difference between the TPS2812 and the TPS2813?

Logic polarity only. The 2812 has two inverting drivers and the 2813 has two noninverting drivers. The body, the pinout, the current and the timing are the same.

Can the part run from a 24 V rail directly?

Yes, through the internal regulator, which is present on the 2811, 2812 and 2813. The dissipation inside the package has to be checked at the switching frequency in use.

Does the regulator output have to be used?

No. REG_IN and REG_OUT can be left open, or tied to VCC or ground, when no regulator output is needed.

How much gate charge can it drive at 100 kHz?

The limit is thermal rather than electrical. The 2 A peak output charges the gate quickly, and the average current is the gate charge multiplied by the frequency. That average current and the regulator drop together set the package temperature.

Is the part still in production?

The vendor document carries revision dates from the 2000s, and the part remains an active order code. Any purchase should confirm the current revision letter on the reel label.

How SUPERB handles this line

Gate drivers on long life boards are a classic case where the drawing is frozen and the part still has to be found years later. Our obsolete part cross reference hub covers the families that have to be re sourced, the lead time solutions page describes how a long lead part is bridged, and our date code management is where the reel records for parts of this age are kept.