TPS2514ADBVR
Product Specifications
TPS2514ADBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2514ADBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2514ADBVR single port USB dedicated charging port controller in a six pin SOT-23
The TPS2514A is the single port member of the TPS251xx family of USB dedicated charging port controllers. It sits on the two data lines of a USB connector and does nothing else: no power switch, no current sense, no converter. Its job is to present the resistor divider signature that a phone or tablet looks for before it agrees to draw more than 500 mA, and it presents that signature without any firmware, since the whole selection is done by the silicon itself.
The A version is the reason the orderable string matters. The plain TPS2514 applies 2 V and 2.7 V across the two data lines for divider 1 and divider 2 of the battery charging specification, while the TPS2514A applies 2.7 V on both lines for divider 3 and also carries the 1.2 V mode plus the shorted mode of BC1.2 and of YD/T 1591-2009. A buyer who orders the plain part for a charger that has to answer a divider 3 request will find the port charging slowly, and nothing on the board will look wrong.
Key parameters taken from the TPS2514ADBVR document
| Operating range | 4.5 V to 5.5 V on IN, which is the USB VBUS window and nothing wider |
| Undervoltage lockout | 3.9 V minimum, 4.1 V typical and 4.3 V maximum on IN rising, with 100 mV of hysteresis |
| Supply current | 155 microamp typical and 200 microamp maximum across the full input range, which is small enough to stay powered from a standby rail |
| Divider mode output | 2.57 V minimum, 2.7 V typical and 2.84 V maximum on both data lines for the A version |
| Divider output impedance | 24 k minimum, 30 k typical and 36 k maximum, which is what the charging device measures as its signature |
| BC1.2 shorted mode | The two data lines are tied together through about 200 ohm, 157 ohm minimum and no maximum printed for the shorting resistance |
| Detach threshold | 310 mV minimum, 330 mV typical and 350 mV maximum on the data line, with 50 mV of hysteresis, below which the part returns to divider mode |
| 1.2 V mode | Both data lines biased to 1.2 V, which is the sixth scheme listed in the feature table |
| Charge pump and bias | Fully internal, no external components on the data lines other than the connector |
| Ports per package | One, in a six pin SOT-23 body of 2.90 mm by 1.60 mm |
| Pin count | Six, of which two are the data lines of the port, one is IN, one is GND and the remaining two carry the second port on the dual member |
| Temperature | Minus 40 to plus 125 degrees, which is the rating printed on the addendum row |
| Package | SOT-23 DBV, six pins |
| Carrier | The plain string is printed at 3000 pieces on a large reel, and the G4 and .A rows of the same body appear at both 250 pieces on a small reel and 3000 on a large reel |
| Moisture | Level 1 at 260 degrees with an unlimited floor life on the reel rows |
| Part marking | Printed as PB3Q on the plain rows and as 2514 on the later rows, which is a marking difference on the same silicon |
| Status | Active and in production on the addendum dated July 2026 |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The divider signature is a resistance, not a voltage source. The 30 k output impedance is what a charging device sees when it pulls a test current, and the printed 2.57 V to 2.84 V window is the open circuit value. A meter on the data line with no load will read the top of the window, and a device that loads the line will read lower, which is why the impedance row is printed next to the voltage row.
The detach threshold is the part of the behaviour that decides whether a port is usable with a device that is unplugged and plugged back in without the VBUS being cycled. Below 330 mV on the data line the part goes back to divider mode and starts the detection sequence again. If the VBUS rail keeps the part alive but the data line is loaded by a cable fault, the part can sit in the wrong mode and the device never sees its signature.
The 1.2 V mode is the one that surprises people who compare datasheets by the headline. A divider 1 and divider 2 signature is a pair of voltages, one 2 V and one 2.7 V, and the two lines are not symmetric. The A version puts 2.7 V on both. A cable or a test fixture that swaps the two data lines will therefore pass on the A version and fail on the plain version, or the reverse, which is a common cause of a port that works on one bench and not on another.
Supply current of 155 microamp typical is small but not zero, and on a charger that has to meet a standby power target the controller is rarely the largest load. The part still needs its IN pin fed from a rail that is present when the port is unattended, so a board that switches VBUS off completely will restart detection each time the port is enabled, which adds a visible delay before a device starts charging.
The undervoltage lockout at 4.1 V typical sits inside the USB 5 V window by a useful margin. A charger with a long cable and a 4.75 V port voltage still keeps the controller alive, while a port that droops below 3.9 V releases the part and the signature disappears. That is the intended behaviour, because a device should not be told it may draw 2 A from a rail that has already collapsed.
- Which member is on the order, the plain part or the A version, because the divider signature differs and the board will not show the difference.
- The two data lines against the connector pinout, since divider 1 and divider 2 are not symmetric and a swap turns a working port into a slow charging port.
- The resistance a charging device will see on each data line, which is the 30 k output impedance and not the open circuit voltage.
- The IN rail, which has to stay inside 4.5 V to 5.5 V and has to be present while the port is unattended.
- The mode the port has to answer, shorted, divider 1, divider 2, divider 3 or 1.2 V, because one part does not answer every scheme.
- The reel size and the marking, since the same body ships under several strings and the marking on the newer rows differs from the older ones.
Which projects this part fits
This part fits wall chargers, vehicle USB sockets, power banks with a fixed output, multi port hubs and any adapter that has to charge a phone at full rate without a microcontroller. It is also used as a repair part on boards where the original controller has failed and the port now charges at 500 mA, because the data line signature is the only thing that decides the current a device will ask for.
Questions that come up before a purchase order is released
What is the difference between the TPS2514 and the TPS2514A?
The A version applies 2.7 V on both data lines for divider 3 and adds the 1.2 V mode. The plain version applies 2 V on one line and 2.7 V on the other for divider 1 and divider 2. Both answer the shorted mode of BC1.2 and YD/T 1591-2009.
Does the part need a microcontroller?
No. Detection and the signature selection are internal, and the part has no digital interface. That is the reason it is used on adapters with no firmware at all.
Can it switch the VBUS current?
No. There is no power switch inside this body. The port still needs a current limited switch or a converter with a current limit, and the data line controller only decides the signature.
What happens if a device is unplugged and plugged back in quickly?
The data line falls below the detach threshold, the part returns to divider mode and the detection sequence starts again. A cable fault that holds the data line above 350 mV can prevent that restart.
Why does the same part number appear with two markings?
The addendum prints PB3Q on the plain rows and 2514 on the later rows of the same body. Both are the same silicon, and a line that checks marking against the orderable string will flag the older rows.
Is the part suitable for a vehicle socket?
The document lists vehicle USB power chargers among its applications and the temperature rating is minus 40 to plus 125 degrees, but the VBUS side has to be protected for load dump by the system, since the part itself is only rated to 5.5 V on IN.
How SUPERB handles this line
This is a high volume, low cost line where the differences between members are on the data lines rather than in the power path, so the buying decision is usually about which signature a target market needs and which reel the line can accept. Our power management cross reference holds the cross reference against the devices this part replaces, and our pin to pin cross reference covers the checks a replacement has to pass before it goes on a board. For programmes that need the controller together with the switch, the connector and the passives from one shipment, our one stop BOM sourcing service is the route we quote.