CD4001BE
Product Specifications
CD4001BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4001BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4001BE: four 2-input NOR gates in the 14-lead plastic DIP
The CD4001BE is the plastic dual-in-line member of the CD4001B family, four independent 2-input NOR gates with buffered inputs and outputs on the 3 V to 18 V CMOS process that the whole CD4000B series shares. TI files the family under document SCHS015C, revision C, which also covers the CD4002B and the CD4025B, and the descriptor on the vendor product page reads four channels, two inputs per channel, 3 V to 18 V. Nothing about the die is unusual: each gate NORs two inputs, every input and every output is buffered, and the output swing sits symmetrically about the supply rails, which is the reason the same part number appears in a 5 V analogue chain and in a 12 V control chain without a second catalogue entry.
The E suffix is what this page is about. The package addendum lists CD4001BE as Active in production, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold lead finish, no moisture sensitivity level because a through-hole body is not reflow classified, an operating range of minus 55 to plus 125 degrees, and the marking CD4001BE on the body. The same addendum carries CD4001BE.A and CD4001BEE4 at the same 25 piece tube, so a purchase order can meet a vendor list that shows three rows for one part number, and the SOIC and TSSOP members of the family sit on separate rows in the same document.
The CD4001BE row as the vendor addendum publishes it
| Part class | Quad 2-input NOR gate, buffered inputs and outputs |
| Vendor descriptor | Four channels, two inputs per channel, 3 V to 18 V |
| Vendor document | SCHS015C revision C, CD4001B, CD4002B and CD4025B |
| Supply range | 3 V to 18 V |
| Parametric ratings | 5 V, 10 V and 15 V tables |
| Propagation delay, vendor figure | 60 ns typical at 10 V into a 50 pF load |
| Output drive, parametric table | 6.8 mA sink and source |
| Data rate, parametric table | 8 Mbps |
| Input current, maximum | 1 microamp at 18 V over the full range, 100 nA at 18 V and 25 degrees |
| Quiescent current | Tested to maximum at 20 V on every unit |
| Noise margin | 1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V |
| Logic standard | JEDEC tentative standard 13B, B series CMOS |
| Package for this code | PDIP (N), 14 leads |
| Packing | 25 pieces in a tube |
| Lead finish | NIPDAU |
| Moisture level | Not applicable for this package type |
| Operating range | Minus 55 to plus 125 degrees |
| Status | Active, production |
| Part marking | CD4001BE |
| Same string in the addendum | CD4001BE.A and CD4001BEE4, both 25 piece tube |
| SOIC members of the family | CD4001BM 50 piece tube, CD4001BM96 2500 piece reel |
| Obsolete row of the family | CD4001BMT, quantity blank, Call TI |
| Last time buy row | CD4001BNSR, 2000 piece reel |
Four NOR gates at 6.8 mA on a 5 V rail
The number most engineers want first is the delay, and the vendor prints one: 60 ns typical at 10 V with a 50 pF load. That is a 10 V figure and it does not transfer to a 5 V rail, where the same gate is slower. The product page does not print a 5 V number, and the Harris era document behind it carries the 5 V, 10 V and 15 V switching tables as images rather than as text, so this page quotes the one figure the vendor states in text and leaves the others to the data sheet rather than guessing them.
The drive figure is the second number that decides whether the part fits. The parametric table gives 6.8 mA sink and source, which is enough to light a small LED through a resistor, drive a transistor base through 1 k, or clock a CMOS input across a short board run. It is not enough to drive a 50 ohm line or a power FET gate at speed, and a part chosen for that duty belongs in a 74AC or a dedicated driver rather than in a 4000B gate.
The DC numbers are where the B series earns its place in an industrial bill of materials. Input current is 100 nA at 18 V and 25 degrees and 1 microamp over the full temperature range, so a 1 megohm pull resistor drops 0.1 V at room temperature and 1 V at the top of the range. An engineer who sizes a pull-up from the 25 degree figure and then runs the board at 100 degrees sees the bias point move, which is exactly the kind of fault that only shows up in a chamber. Noise margin is 1 V at 5 V, 2 V at 10 V and 2.5 V at 15 V over the full range, and the quiescent current is tested to maximum at 20 V on every unit rather than sampled, which is why the part holds its place in circuits that sit biased for years.
Where CD4001BE sits against CD4002BE and CD4025B
Three parts share the same document and the same die process, and the choice between them is a logic question rather than a purchasing one. The CD4001B gives four 2-input gates, the CD4002B gives two 4-input gates, and the CD4025B gives three 3-input gates. A 4-input NOR built from two 2-input NORs costs an inverter and two gate delays, while the CD4002B does it in one gate delay, so a circuit that fans in four signals is better served by the 4002 even though the 4001 has more gates per package.
The reverse case is just as common. Four independent 2-input functions in one 14-lead body usually replace two packages of dual gates, and the CD4001B is the cheapest way to put four NORs on a board. A mixed board that needs two 2-input and one 4-input function takes the 4001 plus a 4002, and a board that needs three 3-input functions takes the 4025B. All three carry the same 60 ns typical figure, the same 6.8 mA drive and the same 3 V to 18 V range, so the substitution between them changes the logic, not the electrical envelope.
The package decision: 25 to a tube and no moisture clock
A through-hole 14-lead body has one practical advantage that is easy to underestimate: it can be socketed. A control board that is repaired in the field, or a prototype that gets reworked every week, can carry a socket and swap the gate without touching the solder. A tube of 25 also suits hand assembly, wave solder and any line that does not run a reflow profile, and because the addendum lists no moisture level for the PDIP body there is no floor life clock to track after the bag is opened.
The cost of that convenience is density and price per unit at volume. A SOIC body occupies about 52 square millimetres against about 181 for the DIP, and the reel member of the family, CD4001BM96, is packed 2500 to a reel against 25 to a tube. On a board that already runs reflow, the DIP is the wrong choice for a new build; on a board that is hand assembled or repaired, it is the right one. Both bodies are the same die, so the electrical numbers above apply to either.
Incoming checks that catch a wrong or aged part
Three checks catch most of what goes wrong with a 4000B logic line. The first is the body marking: CD4001BE is the DIP, CD4001BM is the SOIC and the two are easy to confuse in a mixed goods-in area, and a bag labelled 4001BE that contains SOIC bodies is a real failure mode on a distributor return. The second is the date code, because these parts have been in catalogues for decades and stock that has sat in a warehouse for fifteen years still tests good but may not match the traceability a customer needs. The third is a functional test at the rail the board actually uses: a 5 V truth table check covers the four gates, and a quiescent current reading at 20 V is the same screen the vendor applies to every unit, which makes it a cheap authenticity check on incoming stock.
The pages behind those checks are the incoming inspection plan for the test sequence, date code management for the traceability rule, and the pin to pin cross reference when the question is which other 14-lead NOR can sit in the same socket.
Questions that come up before the order
The first question is whether a 74HC02 can replace this part. The logic function is the same and the package is the same, but the HC family stops at 6 V and uses CMOS thresholds tied to the supply, so it cannot sit in a 12 V circuit and its input levels do not match a 4000B chain at 10 V. In a 5 V circuit the swap is usually possible with a check of the drive and the threshold windows, and above 6 V it is not.
The second question is the difference between the E and the M suffix. Only the package changes, 14-lead PDIP against 14-lead SOIC, together with the packing, 25 to a tube against 50 to a tube and 2500 to a reel for the 96 string. The die, the delay, the drive and the temperature range are identical.
The third question is whether the part runs at 3.3 V. The vendor range starts at 3 V, so it runs, but the 60 ns figure is a 10 V figure and the drive falls with the rail, so a 3.3 V circuit should be checked against the 5 V table and given more margin rather than less.
The fourth question is the difference between the B series and the older A series. The B parts have buffered outputs, higher drive, a quiescent current that is tested to maximum at 20 V on every unit, and conformance to JEDEC 13B. Substituting a B part for an A part is safe in almost every case; the reverse is not, because the unbuffered output cannot drive the same load.