Contact Us

BQ35100PWR

Brand: Texas Instruments
Texas Instruments BQ35100PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ35100PWR — Power Management & Signal Chain | Superb Automation

BQ35100PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ35100PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ35100PWR: gauging a primary cell that must not be discharged for a test

The BQ35100PWR is a fuel gauge for non rechargeable lithium cells. That single sentence decides the whole part, because a primary cell cannot be run flat to find out how much was in it. The gauge therefore works from short measurement windows rather than from a continuous discharge curve, and the host wakes it, lets it take a reading, and puts it back to sleep.

Three methods sit in the same body. State of health suits lithium manganese dioxide cells and tracks capacity loss through the life of the cell. End of service suits lithium thionyl chloride cells and warns when the cell is approaching the point where it can no longer support the load, which on a thionyl chloride cell is a voltage that falls late and fast. Coulomb accumulation works on any chemistry and simply counts charge through the sense resistor.

Average draw is the headline. With the part enabled only for the measurement windows, the average current can be held below 2 microamps, and the vendor publishes the per method figures as roughly 0.06 microamps for state of health, 0.35 microamps for end of service and 0.3 microamps for coulomb accumulation. On a cell that has to last fifteen years in a meter, that difference decides the battery size.

Key data for the BQ35100PWR

FunctionFuel gauge and end of service monitor for primary lithium cells
ChemistriesLithium thionyl chloride and lithium manganese dioxide
MethodsState of health, end of service, coulomb accumulation
Average currentUnder 2 microamps with host controlled measurement windows
InterfaceI2C at 400 kHz, configurable alert interrupt
AuthenticationSHA-1 challenge and response to block counterfeit cells
MeasurementCell voltage, temperature, current across an external sense resistor
Data loggingBattery information records held in the part for field diagnosis
PackageTSSOP, 14 pins, 5.00 mm by 4.40 mm
TemperatureMinus 40 to 85 C operating
OrderingBQ35100PWR, 2000 pieces on a large tape and reel; BQ35100PW, 90 pieces in a tube; both moisture level 2 with a one year floor life, marking BQ35100

Why a thionyl chloride cell needs a different question answered

A lithium thionyl chloride cell holds a flat voltage for most of its life and then falls away over a short window at the end. Reading the voltage therefore tells you almost nothing until it is too late, and a product that warns on a voltage threshold will give days of notice rather than months. The end of service method in this part looks at the cell under a load pulse instead, and the sag under that pulse grows as the cell ages even while the rested voltage is unchanged.

The passivation layer on a thionyl chloride cell adds a second effect. A cell that has been idle builds a layer that shows up as a high internal resistance for the first moments of a load, then breaks down. A measurement taken too early in the pulse reads the layer rather than the cell, which is why the part expects the host to schedule a measurement window long enough for the reading to settle.

Lithium manganese dioxide behaves differently, with a voltage curve that falls more evenly and a capacity that can be tracked. That is why state of health is offered for that chemistry and end of service is offered for the other. Using the wrong method on a given cell does not damage anything, it just produces a number that does not mean what the product thinks it means.

Setting the measurement window

The gauge is powered from the cell through its own regulator, and the host holds the enable pin low when nothing is needed. A typical product wakes the gauge every few hours, lets it measure, reads the result and shuts it down again. The vendor suggests that an eight hour update is enough for many systems, because the part is not required to be powered while the load is running.

The cost of a window is set by how long the regulator takes to settle and how long the measurement itself takes. Both are short, but they are not zero, and a product that wakes every minute will spend more on the gauge than the radio it is powering. Size the interval from the rate at which the cell can change, not from a wish for a live reading.

There is also an inrush item. The regulator charges a capacitor at each wake, and that charge comes out of the cell. A 1 microfarad capacitor charged to 2.5 V is 3 microcoulombs, which is trivial once an hour and less trivial once a second. The capacitor value and the wake interval belong in the same calculation as the cell capacity.

Where it fits in a build

This part belongs in the products that are expected to run on one cell for a decade: utility meters, flow meters, smoke and gas detectors, door access readers, building sensors and remote asset trackers. In every one of those the cell is not replaceable in the field, or replacing it is the expensive part of a service visit, so the value of knowing the end is near is high.

Those products also tend to carry a certified cell with a long lead time, and a change of cell vendor forces a re qualification of the gauge profile. For a programme facing that, the last time buy and LTB planning page sets out how the final buy is sized against the remaining build plan.

The sourcing side of this part is covered on the supplier quality audit. For a cell and a gauge that both have to be traceable, that page covers the records we ask for and keep.

Questions we get on this code

Can it gauge a rechargeable cell? It is built for primary cells, and the algorithms assume a cell that is not recharged. A rechargeable pack needs a gauge with an impedance or voltage correlation model for cycling, and this is not that part.

Does the host have to power the gauge continuously? No, and it should not. The enable pin exists so the host can power the part only for the measurement window, which is where the sub 2 microamp average comes from.

What does the SHA-1 authentication protect against? A counterfeit or a wrong cell fitted into the holder. The host sends a challenge through the gauge, the cell side answers, and a wrong answer can be used to refuse to run or to flag a service action.

Is the sense resistor needed for the state of health method? Yes, current is part of the model, and the resistor value is part of the configuration. A wrong value scales the current reading and the health figure with it.