Contact Us

AMC7812SPAPR

Brand: Texas Instruments
Texas Instruments AMC7812SPAPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AMC7812SPAPR — Power Management & Signal Chain | Superb Automation

AMC7812SPAPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The AMC7812SPAPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

AMC7812SPAPR: twelve 12 bit DACs, a 16 channel ADC and two remote sensors in one HTQFP

AMC7812SPAPR is a complete analog monitoring and control device from Texas Instruments in the 64 pin HTQFP PowerPAD package, the PAP body of 10 mm by 10 mm, supplied on tape and reel. Inside one package it carries twelve 12 bit digital to analog converters with programmable output spans of 0 V to 5 V or 0 V to 12.5 V, a 12 bit successive approximation ADC with sixteen input channels running at 500 kSPS, eight general purpose input and output pins, two remote temperature sensor channels and one internal temperature sensor. Typical power dissipation is 95 mW.

The part exists because an RF power amplifier, a laser driver or an instrument front end needs a dozen bias and control voltages that all have to move together, and building that out of separate converters costs board area, address space and a second reference. One device with a common reference, a common serial bus and an out of range alarm on every channel is how that problem is normally solved. The vendor names RF power amplifier control in base stations as the first application, and the electrical tables in the document are written with that use in mind: fast settling DACs, a monitor ADC that can watch the same rails, and temperature sensing for the devices that drift.

The figures here were read from the vendor document SBAS513E, revised September 2013, which is the document for the AMC7812. The AMC7812B revision exists under a separate document and extends the operating range to 125 degrees; where a number differs between the two it is stated, so that a page written for the AMC7812 is not read as a page for the B part.

What twelve DACs and one ADC buy on a real board

The arithmetic of resolution is the first thing a bias network cares about. A 12 bit converter over a 0 V to 5 V span steps in 1.22 mV, and over a 0 V to 12.5 V span it steps in 3.05 mV. On a GaN or LDMOS gate bias, where the drain current moves by amperes for a few hundred millivolts of gate voltage, that step size is the difference between a bias point that can be trimmed and one that cannot. The 12.5 V span is what makes the same device usable for a varactor or a tuning line that needs more than 5 V.

Settling is 3 microseconds to half a least significant bit for a step in the upper part of the range, into 2 kohm and 200 pF, measured from the rising edge of the chip select. Slew rate is 1.5 V per microsecond and the output can source or sink 8 mA while staying within 25 mV of the setting, which is enough to drive a bias Tee or an attenuator control directly without a buffer. Short circuit current is limited at 30 mA, so a shorted control line does not take the device down with it.

On the monitoring side, the ADC converts sixteen channels at 500 kSPS in auto mode, or 167 kSPS per channel in direct mode, with a 2 microsecond conversion and a 32 microsecond autocycle when all sixteen single ended inputs are enabled. Channels 4 to 15 are single ended; channels 0 to 3 can be four single ended inputs or two fully differential pairs. That mix is deliberate: the differential pair is for a shunt or a bridge that needs the common mode removed, and the single ended channels are for supply rails and bias monitors.

Temperature sensing, alarms and the clear pins

The internal sensor covers minus 40 to plus 125 degrees with an accuracy of plus or minus 2.5 degrees, and resolves 0.125 degrees per step. The two remote channels take a diode connected transistor, the document works its examples around a 2N3906, and cover minus 40 to plus 150 degrees with plus or minus 2 degrees of accuracy between minus 40 and plus 100. Conversion takes 15 ms for the internal channel and between 33 and 100 ms per remote channel depending on whether resistance cancellation is enabled. Resistance cancellation is the setting that removes the error from a long cable to a remote diode, and it costs conversion time, which is a trade a board engineer makes once and then forgets.

Every channel can carry a limit, and the ALARM output is an open drain pin that pulls low when any channel leaves its window. It needs an external 10 kohm pull up. Two DAC clear inputs, active low, force the DAC outputs to a predefined level without touching the data registers, so when the line is released the outputs return to the values the registers hold. That is the pin pair that makes a safe shutdown possible without a bus transaction, and on a power amplifier bias supply it is usually wired to the same supervisor that drives the drain switch.

Where the numbers sit against the B revision

ParameterAMC7812, document SBAS513EAMC7812B, document SBAS625A
DAC channels12, 12 bit12, 12 bit
DAC output spans0 V to 5 V, 0 V to 12.5 V0 V to 5 V, 0 V to 12.5 V
DAC INL and DNLplus or minus 1 LSB, 12 bit monotonicplus or minus 1 LSB, plus or minus 1.25 LSB over the wider range
ADC throughput500 kSPS auto mode, 167 kSPS direct mode500 kSPS auto mode, 167 kSPS direct mode
ADC inputs16 single ended, or 2 differential plus 12 single endedsame
Remote sensor accuracyplus or minus 2 degrees, minus 40 to plus 150plus or minus 2 degrees, minus 40 to plus 150
Internal sensor accuracyplus or minus 2.5 degrees, minus 40 to plus 125plus or minus 2.5 degrees, minus 40 to plus 125
Specified temperatureminus 40 to plus 105 degreesminus 40 to plus 105 degrees
Operating temperatureminus 40 to plus 105 degreesminus 40 to plus 125 degrees
Typical power95 mW95 mW
PackageQFN-64 RGC, HTQFP-64 PAPQFN-64 RGC, HTQFP-64 PAP

The practical difference is the operating range: the B part is specified to 105 degrees and operational to 125, while the plain AMC7812 is a 105 degree device. A board that sits next to an amplifier heatsink and sees 110 degrees should not treat the two as the same purchase line, even though the pin out, the register map and the package are identical.

The figures a hardware engineer checks first

FunctionAnalog monitoring and control with DACs, ADC and temperature sensing
DAC resolution12 bit, 12 channels, string DAC with output buffer
DAC output range0 V to 5 V with gain of 2, 0 V to 12.5 V with gain of 5
DAC step size at 5 V span1.22 mV per least significant bit
DAC step size at 12.5 V span3.05 mV per least significant bit
DAC settling3 microseconds to half a least significant bit
DAC output noise81 nV per root hertz at 1 kHz, gain of 2, reference excluded
DAC load currentplus or minus 8 mA within 25 mV of the setting
ADC resolution and rate12 bit, 500 kSPS auto mode, 167 kSPS direct mode
ADC linearityplus or minus 1 LSB integral, plus or minus 1 LSB differential
ADC common mode rejection67 dB in the doubled reference range
Internal reference2.500 V, plus or minus 5 mV, 10 ppm per degree typical
Analog supply AVDD and DVDD2.7 V to 5.5 V, must be the same value
DAC output supply AVCC4.5 V to 18 V, output must not exceed AVCC
Interface supply IOVDD2.7 V to 5.5 V, 3 V or 5 V logic
Serial interfaceSPI to 50 MHz, or I2C compatible to 400 kHz fast mode
GPIO8 pins, open drain, external pull up required
Alarm outputOpen drain, 10 kohm pull up, out of range on any channel
Thermal resistance, PAP33.7 degrees per watt junction to ambient
Package and carrierHTQFP-64 PowerPAD, 10 mm by 10 mm, tape and reel

Board level traps that the tables do not shout about

The first is the supply order. AVDD must be at or above the reference plus 1.2 V for the reference buffer to work, and the DAC output can never exceed AVCC whatever the register says. A board that runs AVCC at 5 V and asks for the 12.5 V span will simply clip at 5 V, and the clipping is silent because the register still reports the requested code.

The second is the reference loading. The internal reference sources and sinks 5 mA and is not a rail for the rest of the board. If the same 2.5 V is needed elsewhere it has to be buffered, which the document states plainly and which is the most common reason a second board revision is needed.

The third is the ground split. The device has four analog grounds plus digital ground, and the ADC ground pin must be tied to analog ground. A ground join at the thermal pad and nowhere else is what the thermal numbers assume; a join under the ADC will put the digital return current through the analog reference and show up as code noise that no amount of averaging removes.

The fourth is the pull ups. GPIO0 to GPIO3 must be pulled to a voltage at or below 5.5 V, while GPIO4 to GPIO7 are shared with the remote diode inputs and must be pulled to AVDD or below. On a 3.3 V logic board with a 5 V analog rail, mixing those two groups is an easy mistake and a hard one to find afterwards.

What we do around this part

The part is a 64 pin PowerPAD package with a thermal pad that has to be soldered, on a board that usually also carries the amplifier it is biasing. Incoming inspection on a part like this is a solderability and coplanarity check plus a first article functional test on the serial bus, not a visual pass. We can supply the part with a date code report and a certificate of conformance, and we can hold a stock position against a build plan when the annual volume is known.

Pages that go with this one: ADC DAC cross reference for the alternative list when the B revision or a different channel count is needed, pin to pin cross reference for checking whether a candidate really shares the footprint, component lead time solutions for the schedule side, and high speed digital board support for the assembly side of a mixed signal board.

Questions buyers ask about the AMC7812

Is the AMC7812 the same as the AMC7812B. No. The pin out, the package and the register map match, the operating range does not. The plain part is specified and operational to 105 degrees; the B part is specified to 105 and operational to 125. Substituting one for the other on a hot board is a decision that has to be made against the thermal calculation, not against the datasheet headline.

Can the twelve DACs be updated at the same time. Yes. The load DAC pin and the two clear pins are there for that, and the clear function forces a predefined level without losing the register contents, so the outputs can be parked and restored without rewriting twelve registers over the bus.

What does the part cost in power. 95 mW typical with all twelve DACs at mid code and both converters running at the fastest auto rate, 120 mW maximum. On a 15 V AVCC that is a few milliamps, which is why the device is used to replace a rack of separate converters in the first place.