Contact Us

BQ24078RGTR

Brand: Texas Instruments
Texas Instruments BQ24078RGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24078RGTR — Power Management & Signal Chain | Superb Automation

BQ24078RGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24078RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24078RGTR single cell charger with power path and a 4.35 V battery regulation point

The BQ24078RGTR is a linear lithium ion charger for one cell packs that also carries a system power path. It runs from a USB port or a wall adapter, takes up to 1.5 A of charge current, and keeps the system rail supplied from the input while the pack is charging. The regulation point is the detail that separates it from the more common 4.20 V parts: this member of the bq2407x family regulates the battery at 4.35 V typical, which is the correct ceiling for the higher voltage cell chemistries used in slim phones, wearables and portable medical handhelds.

The family is documented in one file together with the bq24076, which regulates at 4.4 V, so the two codes share a pinout and differ only in the regulation target. Input is rated to 28 V with overvoltage protection, so an unregulated adapter or a poor USB source does not have to be cleaned up in front of the charger. The input current limit is programmable up to 1.5 A for a wall adapter and can be pinned to 100 mA or 500 mA for USB compliance, which is what allows one board to pass a USB-IF review and still charge quickly from a 5 V 2 A adapter.

Key parameters taken from the BQ24078RGTR document

Functionlinear single cell lithium ion charger with dynamic power path management
Family in the documentbq24076 regulates at 4.4 V, bq24078 at 4.35 V, one body and one pinout
Charge currentup to 1.5 A with current monitoring on the ISET output
Input current limit100 mA or 500 mA pin selected for USB, programmable up to 1.5 A for an adapter
Input rating28 V absolute with input overvoltage protection
Power pathDPPM, system output tracks the battery voltage, supplement mode from the pack
Battery disconnectSYSOFF input turns the pack off from the system
Termination and timersprogrammable pre-charge and fast charge safety timers
Protectionreverse current, short circuit, thermal, NTC thermistor input
Status outputscharging and done, plus power good
PackageVQFN RGT, 16 pins
Order code factsBQ24078RGTR, 3000 pieces on a large reel, MSL Level-2-260C-1YEAR, minus 40 to plus 85 C, marking B24078, Active

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The 4.35 V regulation point is not a small print item. A pack built around a conventional 4.20 V cell will be over charged by this part and will lose cycle life, and a protection board sized for 4.25 V will trip. Before the first article is built, confirm the cell specification sheet states a 4.35 V or 4.4 V charge ceiling. If the cell is a 4.20 V type, this code is the wrong member of the family and the bq2407x variant that regulates at 4.2 V is the one to quote.

Thermal budget decides the real charge current. A linear charger drops the difference between the adapter voltage and the battery voltage across its pass element, so 5 V in and 3.7 V out at 1.5 A is about 1.95 W inside a 3 mm body. The vendor states a thermal regulation loop that folds the current back as the die heats, which means the 1.5 A headline is reachable on a board with copper to the thermal pad, and a sealed enclosure without it will settle well below that number. The pad has to be soldered to a plane with vias, not left floating on a small island.

The power path is what makes the part useful in a product that must run with a flat pack. The system output follows the battery voltage through the DPPM loop, and when the input cannot supply both the system and the charge current, the charge current is reduced first. With the pack removed the system still runs from the adapter, which is the behaviour a factory test needs, since boards can be tested without a battery fitted. SYSOFF gives the opposite ability, cutting the pack off the system so that a stored product does not drain itself through the load.

The USB compliance path has two limits that are easy to confuse. Pinning the input limit to 100 mA satisfies the USB-IF requirement for an unconfigured port, and 500 mA covers a configured port. The programmable limit up to 1.5 A is for an adapter, and a product that always asks for the high limit from a USB host will be non compliant regardless of what the charger can do. The NTC input should be populated even when the pack is a simple one, because the JEITA style fold back is implemented through that pin and a fixed resistor in its place disables the temperature protection silently.

The order code ends in R for tape and reel, and the addendum prints one row for this code, 3000 pieces on a large reel at Level 2 moisture sensitivity with a one year floor life. That floor life matters on a line that opens a reel and then reflows a small batch, because the parts have to be baked or kept in a dry cabinet between runs.

  • The regulation target differs between the two codes in this document, so the pack specification has to be read before the reel is ordered.
  • Input overvoltage protection at 28 V means an adapter with a poor transient does not require an external clamp, but the data line pins still need their own protection.
  • The charge timer is set by an external component, so a slow charge at low input current does not trip the safety timer if the value follows the vendor table rather than a copied value.
  • The current monitor output scales with the actual charge current, which gives a test fixture a way to confirm the loop without breaking the current path.
  • The marking is B24078 on the body, which is the shortest way to tell this part from the bq24076 on an incoming inspection bench.

Which projects this part fits

One cell products that charge from USB and must run while charging fit this part: handheld medical monitors, wearable health devices, portable instruments, barcode readers, navigation units and small home automation panels. It is also the part to look at when a product is moving from a 4.20 V pack to a higher voltage cell and the existing charger cannot reach the new ceiling. Buyers comparing it with a discrete charger plus an ideal diode path usually do it to remove board area and to stop the system from browning out at low battery. Our power management cross reference lists what we hold against this family, and the medical device components page covers the traceability that a regulated product needs.

Questions that come up before a purchase order is released

Can this charger work with a 4.2 V pack?

No, not without changing the regulation target. The bq24078 regulates at 4.35 V typical and the bq24076 at 4.4 V. A 4.2 V cell charged to 4.35 V sits above its ceiling and its protection board may cut off before the charger terminates, so the correct move is to select the family member that matches the cell rather than to rely on the timer to stop the charge early.

What has to be on the board for the power path to work with no battery?

The system output and the sense resistor path have to be populated, and the battery node needs enough capacitance to keep the loop stable when the pack is absent. Boards that omit the battery capacitor often show a start up hiccup in factory test with no pack fitted, which reads as a charger failure when it is a loop stability issue.

How is the input current limit set for a USB port?

Two pins select the 100 mA and 500 mA USB settings, and an external resistor sets the higher adapter limit. The setting is a hardware choice, not a register write, so the same board cannot be a 100 mA device and a 1.5 A device at different times unless the pins are driven by the host, which the vendor reference board shows.

How SUPERB handles this line

We supply the BQ24078RGTR as a tape and reel line item with date code and lot traceability, and we check the pack specification against the regulation point before a reel is committed. If the pack is moving to a higher voltage cell, send the cell specification sheet and the existing charge circuit and we will confirm which family member the board needs. Start from the component lead time solutions page if the schedule is already tight.