Contact Us

ADXL326BCPZ

Brand: Analog Devices
Analog Devices ADXL326BCPZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADXL326BCPZ — Analog & Mixed-Signal ICs | Superb Automation

ADXL326BCPZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADXL326BCPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADXL326BCPZ: a 16 g analog accelerometer and the filter capacitor that sets its band

The ADXL326BCPZ is a three axis analog output accelerometer with a 16 g full scale range and a 57 millivolt per g sensitivity at 3 V, in a 4 mm by 4 mm by 1.45 mm lead frame chip scale package. It has no digital interface and no register map: the output is three analog voltages and the bandwidth is set by three capacitors.

Published values

ParameterValue
Rangeplus or minus 16 g on all three axes
Sensitivity57 mV per g typical at 3 V, ratiometric to supply
Supply1.8 V to 3.6 V
Bandwidth0.5 Hz to 1600 Hz on X and Y, 0.5 Hz to 550 Hz on Z
Internal filter resistorabout 32 kohm per axis
Outputthree analog voltages, rail to rail amplifier
Self testelectrostatic actuation on all three axes
Package16-lead LFCSP, 4 mm by 4 mm by 1.45 mm

What 16 g and 57 mV per g put on the pin

Sixteen g at 57 millivolts per g is 912 millivolts of swing either side of the zero g level. On a 3 V supply the zero g level is nominally half the rail, 1.5 V, so the output travels between 588 millivolts and 2.412 volts at full scale. The amplifier still has 588 millivolts of headroom at the bottom, which is what lets the part survive an over range event without clipping the reading away.

Because the sensitivity is ratiometric, the same 912 millivolts becomes 1.094 volts on a 3.6 V rail and 547 millivolts on a 1.8 V rail. A build that reads the output with a fixed reference has to scale for the actual rail, otherwise a five percent supply error becomes a five percent gravity error.

The capacitor is the bandwidth, and the band sets the noise

Each axis has an internal resistor of about 32 kohm in series with the output, so the external capacitor forms a single pole. A 0.1 microfarad capacitor gives a corner near 50 Hz, 0.01 microfarad near 500 Hz, and the data sheet band of 1600 Hz on X and Y corresponds to a few nanofarads. The Z axis stops at 550 Hz, so a build that needs one band on all three axes is limited by Z.

Widening the band admits more noise, and narrowing it delays the response. A tilt sensing build that only needs a few hertz should use a large capacitor and take the noise reduction, while a shock or vibration build has to keep the band wide and accept the noise.

Where an analog output still wins

There is no serial bus, no power up sequence and no register write, so the part works from the first millisecond after the rail is valid. On a safety or trip circuit that is the reason to choose it over a digital part: the comparator sees the analog output directly and there is nothing to initialize.

The cost is pin count and an ADC. Three analog channels plus a reference and a comparator is more board area than one digital part with an SPI bus, so the choice usually follows the host: a microcontroller with three spare ADC channels takes the analog part, a host with no ADC takes a digital one.

When the exact part is not on the shelf

Sourcing notes for this family: the pin to pin cross reference holds the cross references, how to verify a drop in replacement is the pre substitution check, and BOM shortage recovery is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

How do I set the bandwidth? With one capacitor per axis. The internal 32 kohm resistor and the capacitor form a single pole, so 0.1 microfarad gives about 50 Hz and 0.01 microfarad about 500 Hz, with the Z axis limited to 550 Hz.

Is the output ratiometric? Yes. The sensitivity is proportional to the supply, so a 3.6 V rail gives 68 millivolts per g against 57 at 3 V, and the reading has to be scaled by the actual rail.