Contact Us

ADXL346ACCZ

Brand: Analog Devices
Analog Devices ADXL346ACCZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADXL346ACCZ — Analog & Mixed-Signal ICs | Superb Automation

ADXL346ACCZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADXL346ACCZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADXL346ACCZ: 13-bit digital accelerometer with a fixed LSB and four ranges

The ADXL346ACCZ is a three axis digital accelerometer in a 3 mm by 3 mm by 0.95 mm package with a 13-bit output, four selectable ranges and a 32-level FIFO, on either an SPI or an I2C bus. It is the part to look at when the board has no spare ADC channels and the host needs interrupts rather than a stream.

Published values

ParameterValue
Resolution13-bit at full resolution
Scale factor3.9 mg per LSB in full resolution mode
Rangesplus or minus 2, 4, 8 and 16 g, set by serial command
Current23 microamps in measurement mode at 2.6 V
Standby0.2 microamps
Buffer32-level FIFO
InterfacesSPI, 3 or 4 wire, and I2C
Sensing functionsactivity, inactivity, tap, freefall, orientation
Package16-lead, 3 mm by 3 mm by 0.95 mm

A fixed LSB across four ranges is the unusual part

In full resolution mode the scale factor stays at 3.9 milligrams per LSB whatever range is selected, which means the number of codes actually used rises with the range: about 512 codes either side at 2 g, and about 4096 either side at 16 g. The resolution in physical units is the same on every range and the dynamic range is what changes.

Fixed 10-bit mode is the opposite: the same 1024 codes are spread across the selected range, so at 16 g one LSB is 15.6 milligrams, four times coarser. A build that switches ranges at run time and assumes a fixed LSB will misread the data after the switch, which is a firmware bug rather than a part problem.

Twenty three microamps is the measurement figure, not the system figure

The 23 microamp figure applies at 2.6 V in measurement mode, and the data sheet states that consumption scales with bandwidth, so a lower output data rate draws less. The 0.2 microamp standby figure is three orders of magnitude lower, which is what makes a motion triggered wake up worth wiring: the part can sit in standby, wake on activity and hand the host a single interrupt.

The FIFO is what makes that work in practice. Thirty two samples buffered means the host can sleep between bursts instead of servicing an interrupt per sample, and the trigger can be mapped to either of the two interrupt pins so the wake line and the data ready line stay separate.

Reading the part on an existing board

The bus choice is not free: the same package supports SPI and I2C, and the mode is selected by pin strapping on power up, so a substitute that only speaks one of them cannot be strapped into the other. Before a replacement is accepted, the strap pins and the part number suffix have to be compared, then the range and the scale factor confirmed by reading a register.

Orientation detection is four and six position and is computed in the part. A product that relies on it has to reproduce the exact threshold and hysteresis settings after a swap, because the defaults are not the same across the family.

Second position on the digital accelerometer family

Buyers usually arrive at the pin to pin cross reference to find the family alternatives, then use how to verify a drop in replacement to confirm a substitute before it is fitted; component obsolescence management is the routine for a part that has already stopped shipping.

Two questions buyers ask

Does the resolution change when I change range? In full resolution mode it does not: the scale factor stays at 3.9 milligrams per LSB and the number of codes used grows with the range. In fixed 10-bit mode the LSB grows with the range instead.

Is the bus selectable after assembly? No. SPI or I2C is chosen by pin strapping at power up, so the choice is fixed by the board and a substitute that speaks only one of the two cannot be strapped into the other.