AMC1311BDWVR
Product Specifications
AMC1311BDWVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The AMC1311BDWVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AMC1311BDWVR: reinforced isolated amplifier with a 2 V high impedance input, B grade accuracy
AMC1311BDWVR is the isolated voltage sense stage on a bus that needs a reinforced barrier in a SOIC body of 8 pins. The B grade of the part measures a 2 V input through a high impedance front end with fixed gain of 1, offset error of 1.5 mV maximum, offset drift of 10 microvolts per C maximum, gain error of 0.2 percent and gain drift of 40 ppm per C. Isolation is 7000 V peak reinforced per DIN EN IEC 60747-17 and 5000 V RMS for one minute, with a working voltage of 1500 V RMS.
Order code and package
| Order code | AMC1311BDWVR |
| Function | isolated amplifier, gain 1, high impedance 2 V input |
| Isolation | 7000 V peak reinforced per DIN EN IEC 60747-17, 5000 V RMS one minute |
| Working voltage | 1500 V RMS |
| B grade offset | 1.5 mV maximum, 10 microvolts per C maximum drift |
| Standard grade offset | 9.9 mV maximum, 20 microvolts per C typical drift |
| Gain error | 0.2 percent maximum on the B grade, 1 percent on the standard grade |
| Package | SOIC, 8 pins, wide body |
| Temperature range | minus 40 to plus 125 C |
| Missing supply detection | integrated, so a dead high side is reported rather than read as zero |
| Datasheet | SBAS786 revision C |
Electrical parameters that decide the application
| Nonlinearity | 0.04 percent maximum |
| Offset | 1.5 mV maximum, 0.075 percent of the 2 V range |
| Offset drift | 10 microvolts per C maximum, 1.25 mV over the span |
| Gain drift | 40 ppm per C maximum, 5000 ppm over the span |
| Working voltage | 1500 V RMS continuous, which is higher than the 1000 V RMS of the automotive member |
| Common mode | the high impedance input sets the divider current, so the divider can be in the hundreds of kilo-ohms |
| Supply | 3.0 to 5.5 V both sides |
| Missing supply flag | reports a high side that has lost power, which a plain amplifier reads as a zero signal |
| Package | wide body SOIC 8 |
| Grade | the B in the order code is the accurate grade, not a temperature grade |
Points to check before this part goes on a BOM
The B grade differs from the standard part in accuracy, not in temperature or isolation: 1.5 mV against 9.9 mV of maximum offset, and 0.2 percent against 1 percent of gain error. A BOM line written without the B will be filled with the loose grade and the difference only appears in the current reading.
Fifteen hundred volts RMS of working voltage is the number a 1000 V DC bus is checked against, and it is higher than the 1000 V RMS of the automotive member of the family. The peak withstand figure is a test, not an operating point.
Missing supply detection is what separates a real zero from a dead high side. Without it, a failed isolated supply produces a clean 0 V reading, which a controller interprets as a healthy bus at zero volts and acts on.
Gain drift of 40 ppm per C is 5000 ppm over 125 C, or 0.5 percent, which is more than twice the initial gain error. On a calibrated stage the drift is the term that decides accuracy at the temperature extremes, not the 25 C specification.
A high impedance input allows a divider in the hundreds of kilo-ohms, so a 1000 V measurement dissipates a few milliwatts instead of watts. The divider's own tolerance and temperature coefficient then sit in series with a 0.2 percent gain error and are usually the larger term.
Where this order code fits
Voltage sense stages that need reinforced isolation and 1500 V of working voltage start here rather than at the automotive member of the family. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
What does the B in the order code mean? It is the accurate grade: 1.5 mV of offset against 9.9 mV, and 0.2 percent of gain error against 1 percent. Isolation and temperature are unchanged.
How is a dead high side supply reported? The integrated missing supply detection drives the output to a state the controller can tell apart from a genuine zero reading.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.