Contact Us

AMC1211AQDWVRQ1

Brand: Texas Instruments
Texas Instruments AMC1211AQDWVRQ1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AMC1211AQDWVRQ1 — Power Management & Signal Chain | Superb Automation

AMC1211AQDWVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The AMC1211AQDWVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

AMC1211AQDWVRQ1: automotive isolated amplifier with a 2 V high impedance input for voltage sensing

AMC1211AQDWVRQ1 is the isolated voltage sense stage, built around a resistive divider rather than a shunt in a SOIC body of 8 pins. The part measures a 2 V input through a high impedance front end, with fixed gain of 1, offset error of 1.5 mV maximum and offset drift of 10 microvolts per C maximum. Isolation is 4250 V peak basic per DIN EN IEC 60747-17 and 3000 V RMS for one minute per UL1577, working voltage is 1000 V RMS, and the part is qualified to AEC-Q100 grade 1.

Order code and package

Order codeAMC1211AQDWVRQ1
Functionisolated amplifier, gain 1, high impedance input
Input range2 V, for a resistive divider
Isolation4250 V peak basic per DIN EN IEC 60747-17, 3000 V RMS one minute per UL1577
Working voltage1000 V RMS
Transient immunity30 kV per microsecond minimum
QualificationAEC-Q100 grade 1, minus 40 to plus 125 C
PackageSOIC, 8 pins, wide body
Shutdownshutdown input with an internal 100 kohm pull-up
DatasheetSBAS896 revision C
Part nameAMC1211A-Q1 in earlier prints, order code unchanged

Electrical parameters that decide the application

Offset error1.5 mV maximum, which is 0.075 percent of the 2 V input range
Offset drift10 microvolts per C maximum, 1.25 mV over the 125 C span
Gain error0.2 percent maximum
Gain drift40 ppm per C maximum, 5000 ppm over the span
Nonlinearity0.04 percent maximum
Common mode rejectionsufficient to hold the accuracy across the divider's common mode, which is the bus
Transient immunity30 kV per microsecond, revised down from 100 kV per microsecond in revision C
Supply3.0 to 5.5 V on both sides, so a 3.3 V controller needs no translator
Shutdowninternal pull-up means the part is enabled when the pin floats
Packagewide body SOIC 8, 5.85 mm by 7.50 mm

Points to check before this part goes on a BOM

Revision C of the document lowered the common mode transient immunity from 100 kV per microsecond to 30 kV per microsecond. A product that qualified against the earlier print has a margin assumption in its file that the current document no longer supports.

Ten microvolts per C of offset drift is 1.25 mV across the full 125 C span, which is 0.06 percent of the 2 V range. That is smaller than the 0.2 percent gain error, so on this part the divider tolerance and the gain term dominate, not the offset.

A 2 V input with a high impedance front end is built for a divider, not a shunt. The divider ratio sets the bus voltage that maps to 2 V, and the divider's own tolerance and temperature coefficient sit in series with a 0.2 percent gain error, so a 1 percent resistor pair is the accuracy limit of the stage.

The input impedance is high enough that the divider can be in the hundreds of kilo-ohms, which keeps the standing loss of a 800 V measurement in the milliwatt range. A low impedance front end would need a divider that dissipates watts continuously.

Working voltage of 1000 V RMS is the number the divider has to be sized around. A 800 V DC bus with transients above 1000 V RMS equivalent needs a part with more headroom, whatever the 4250 V peak withstand figure says.

The shutdown pin has an internal pull-up, so the part runs when the pin is left open. A board that expects the pin to default to off will find the amplifier enabled and drawing current from the isolated supply.

Where this order code fits

Voltage sense stages pair this part with a divider sized on the working voltage, while current sense stages use the 250 mV members of the family. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

What changed in revision C? The transient immunity figure dropped from 100 to 30 kV per microsecond, and the isolation standard was restated as DIN EN IEC 60747-17.

Can it measure a shunt directly? No. The input range is 2 V with a high impedance front end, which suits a divider; a shunt signal is millivolts and belongs on the 250 mV part.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.