Contact Us

ADS6142

Brand: Texas Instruments
Texas Instruments ADS6142 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS6142 — Power Management & Signal Chain | Superb Automation

ADS6142

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS6142 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS6142: single channel 14 bit 65 MSPS converter in a 32 pin QFN

ADS6142 is the 65 MSPS member of the single channel 14 bit family that fits a 5 mm square body and runs at 285 mW in a QFN body of 32 pins. The ADS6142 is a single channel 14 bit converter that samples at 65 MSPS in a 32 pin QFN body of 5 mm by 5 mm, at 285 mW. It shares its document and its pin out with the 80, 105 and 125 MSPS members, offers DDR LVDS or parallel CMOS outputs, and provides coarse gain of 3.5 dB and fine gain of up to 6 dB programmed over a three wire serial interface. The family table gives 95 dB of SNR at a 10 MHz input for this rate.

Order code and package

Order codeADS6142
Channelsone
Resolution14 bit, no missing codes
Maximum sample rate65 MSPS
Family rates125, 105, 80 and 65 MSPS
Output interfaceDDR LVDS or parallel CMOS
Package32 pin QFN, 5 mm by 5 mm
Power285 mW at 65 MSPS
Gain control3.5 dB coarse, up to 6 dB fine, over a three wire serial interface
Input range2 V peak to peak differential
Clock amplitudedown to 400 mV peak to peak
DocumentSLWS198B, July 2007, revised March 2008

Electrical parameters that decide the application

SNR at a 10 MHz input95 dB, from the family table at this rate
Power per sample4.38 nJ at 65 MSPS
Data rate at 14 bit910 Mbps at 65 MSPS
Quantisation floorabout 86 dBFS for an ideal 14 bit converter
Coarse gain3.5 dB
Fine gainup to 6 dB
Interfacethree wire serial for gain, offset and output format
Offset correctionon chip
Temperatureminus 40 to 85 C
Referenceinternal, external option
Package sharingsame body as the 80, 105 and 125 MSPS members
Board area25 square mm for the body

Points to check before this part goes on a BOM

The 95 dB figure at 65 MSPS is the best in the family and it is the reason this member is still bought. A slower converter integrates over a narrower noise band, so the same die measures better, and a receiver that only needs 30 MHz of bandwidth gets 7 dB more dynamic range than the 125 MSPS member of the same family.

285 mW in a 5 mm square body is 4.38 nJ per sample, and it is what allows a board to carry eight or sixteen channels without a thermal problem. The package has no room for a large pad, so the ground plane under it is the whole thermal answer and it has to be continuous.

At 65 MSPS the interface is 910 Mbps, which is comfortable for both a small FPGA and a parallel CMOS capture. This is the member where the CMOS option is realistic: 14 data lines plus clock at 65 MHz is a bus an older device can still take, while the 125 MSPS member needs the LVDS path in practice.

The gain and offset settings arrive over a three wire serial interface, so the part is configured at start up rather than by pin strapping. On a board with many channels that is convenient, but it also means a channel that is not configured runs at its default full scale, which is a failure mode that shows as a gain difference between channels.

SNR of 95 dB against a quantisation floor of 86 dBFS means the part is better than its own resolution, which only makes sense because the figure is measured in a narrow band and the converter noise is shaped. The useful reading is that the analog front end, not the converter, sets the system noise for any realistic signal chain.

The 2 V peak to peak differential input range with 3.5 dB of coarse gain gives a way to trade input range for SFDR. In a channel where the largest signal is known and the smallest matters, reducing the full scale raises the resolution per code at the cost of headroom, and that trade is made in the register rather than on the board.

Package sharing across four rates means the same 5 mm footprint serves a product line. A board built around this part can take the 80 or 105 MSPS member later if the clock and the capture device allow, which is a real option when a product family is planned over several years.

The 32 pin body leaves a small pad, so the ground plane under the part is the whole thermal answer. On a board that repeats this converter eight times, the plane has to stay continuous between channels, and a split under one part shows as a channel that runs hotter and drifts more than its neighbours.

Where this order code fits

This order code fits compact receive channels where board area matters: portable instruments, hand held spectrum analysers, medical monitors with a small channel count, and industrial imaging boards that repeat a converter many times. The 5 mm body and 285 mW make it the practical choice where the dual channel part will not fit. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is this part pin compatible with the faster members of the family? Yes, the 32 pin body and the pin out are shared across the four rates. The rated rate, the power and the clock are what change.

Why does the slower member have better SNR? A lower sample rate integrates noise over a narrower band. The family table gives 95 dB here against 90 dB at 125 MSPS.

Can it drive a parallel CMOS capture directly? At 65 MSPS the CMOS option is 14 data lines plus clock at 65 MHz, which most capture devices can take without an LVDS receiver.

SUPERB supplies this order code with the date code and packing on the offer, and the One Stop BOM Sourcing page lists the fields to compare before a 32 pin socket is filled from a different line.