TPS72012DRVR
Product Specifications
TPS72012DRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS72012DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS72012DRVR: 350 mA low dropout regulator with a bias pin, fixed 1.2 V output, in a 2 mm by 2 mm WSON
TPS72012DRVR is a linear regulator for a 1.2 V rail that has to sit within a per cent of its setpoint while the rail in front of it switches in a WSON body of 6 pins. It is the 1.2 V member of the TPS720 fixed family, and it exists for the case where a 1.5 V or 1.8 V converter output has to become a quiet 1.2 V rail without a second inductor.
Order code and package
| Order code | TPS72012DRVR, DRV package, WSON 2 mm by 2 mm, six pins with a thermal pad, 3000 pieces on a large reel |
| Body options | DRV six pin WSON to the full temperature range, YZU five pin die scale package to a narrower one |
| Fixed output | 1.2 V on this code, with TPS72010 at 1.0 V, TPS72018 at 1.8 V and the TPS7201 adjustable |
| Output capacitor | 2.2 uF ceramic, the value every transient and start-up limit in the data sheet is measured at |
| Enable | A dedicated pin, so the rail can be sequenced independently of the input |
| Pins | IN, OUT, BIAS, EN, GND and the thermal pad |
Electrical parameters that decide the application
| Input range | 1.1 V to 4.5 V on IN, with the output at least 500 mV below the input for full specification |
| Bias rail | 2.5 V to 5.5 V, which is where the drive current comes from and what makes the low dropout possible |
| Output current | 350 mA continuous, with current limit and thermal shutdown behind it |
| Dropout | 110 mV at 350 mA, so a 1.2 V output needs 1.31 V on IN at full load |
| Quiescent current | 38 uA typical on the bias rail with a light load |
| Noise | 48 uV RMS from 10 Hz to 100 kHz, 4 per cent of a 12 bit step on a 1.2 V rail |
| Rejection | 80 dB from IN and 70 dB from BIAS, both specified from 10 Hz to 10 kHz |
| Accuracy | 1 per cent over line, load and temperature on the DRV package |
| Transients | 15 mV for a 0 to 350 mA step in 1 us, 200 uV for a 400 mV step on the input |
| Start-up | 140 us, monotonic, with overshoot held to 3 per cent and inrush to 100 mA plus the load |
Family variants and how they differ
| TPS72010DRVR | the 1.0 V trim of the same die, for a core rail that needs even less headroom |
| TPS72018DRVR | the 1.8 V trim, which has more headroom and dissipates more heat at the same current |
| TPS7201DRVR | the adjustable version, for a rail that is trimmed at test rather than fixed by the order code |
| TPS7A4901 | a higher voltage LDO from a different family, for a rail that has to start from 12 V or more |
| The converter output directly | the option to drop the regulator and accept the switching ripple, which is the decision this part exists to answer |
Points to check before this part goes on a BOM
A 1.2 V rail from a 1.5 V converter leaves 300 mV of headroom, and the regulator needs 110 mV of it at 350 mA. That leaves 190 mV for the tolerance of the converter, the ripple on its output and the drop in the copper, which is enough on paper and tight in practice. The 500 mV figure in the specification table is the condition for the published accuracy, not a requirement, so a board running at 300 mV of headroom gets the dropout behaviour but should not expect the same line regulation.
The 1 per cent accuracy is what separates this from a resistor divider on a converter. A 1 per cent reference plus 0.1 per cent resistors is a per cent and a half before temperature, which on 1.2 V is 18 mV, and a rail that feeds a DDR interface or a serializer has a window that this error eats into. The regulator holds its 1 per cent over line, load and the full range on the DRV body, which is the reason to pay for it.
The bias pin has to come from a rail that is already up, and on most boards that is the 3.3 V or 5 V housekeeping supply. If the bias comes from the same 1.5 V converter that feeds IN, the regulator will not start at all, because 2.5 V is the floor on BIAS. Sequencing is therefore part of the electrical specification, not just a power-up preference, and a board that enables all three rails together has to check that BIAS rises first.
Noise of 48 uV RMS is a third of the 150 mV that a 2.4 MHz converter typically leaves on a 1.2 V rail, and it is the number that matters for an analog load. The 80 dB rejection is specified only to 10 kHz, so the regulator does not filter the switching frequency by that figure; what it does at 2.4 MHz comes from the output capacitor and the loop bandwidth, which is why the 2.2 uF value is not negotiable.
The 15 mV load transient is specified for a 0 to 350 mA step in 1 us, which is faster than most loads on a 1.2 V rail actually move. A load that steps in 100 ns will see more than 15 mV, and a load that steps in 10 us will see less. The number is a benchmark for comparison rather than a guarantee, and the output capacitor is the first lever when a real load overshoots it.
Dissipation at 1.5 V in and 1.2 V out is 105 mW at 350 mA, which the 2 mm by 2 mm WSON holds with a modest copper pad. From 1.8 V in the same load dissipates 210 mW, and from 3.3 V it is 735 mW, which is past what the body can do without a plane and a thermal via field. The part is a low headroom regulator by intent, and every volt of input above the output is heat.
The enable pin is separate from the input so the rail can be sequenced, and the 140 us start-up is short enough that the sequence timing has to be planned rather than assumed. Two of these enabled by the same signal will both ramp in 140 us and their inrush, limited to 100 mA each plus the load, adds on the rail that feeds them. A board with five of these on one 1.5 V converter is asking that converter for half an amp of inrush at once.
The order code carries the voltage, so a change from 1.2 V to 1.0 V is a different part rather than a resistor change. That is a procurement detail with a real consequence: a build that has to support two core voltages needs two line items and a place for both on the pick list, and a substitution between them is not a drop in replacement even though the body and the pin out are identical.
Where this order code fits
It belongs on the 1.2 V rail of a DDR memory interface, a serializer or deserializer supply, an ADC analog rail or a low jitter clock buffer, where a converter output has to become quiet without a second switching stage. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Can it run from the 1.2 V rail it is generating? No. The input has to be at least 500 mV above the output for full specification, and 110 mV above it to stay in regulation at 350 mA.
Is 1.2 V available in the smaller package? Yes, the YZU die scale body exists, but its accuracy is specified over a narrower temperature range, so the two are not interchangeable on a specification review.
What happens if the bias rail is missing? Nothing starts. The regulator needs 2.5 V on BIAS regardless of how healthy the input is, which is the most common cause of a rail that reads zero on a new board.
How does it compare with a converter for noise? 48 uV RMS against the millivolt level ripple of a switching stage, which is why a converter feeding an analog rail is usually followed by a part like this.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.