MLCC and Ceramic Capacitors for RF and Power Boards
Product Specifications

Product Overview
A multilayer ceramic capacitor is the default part for decoupling, coupling and tuning on a mixed signal board. The dielectric decides what the part is good for: Class I C0G holds its value over temperature and over applied voltage and is used in filters and matching networks, while Class II X7R and X5R pack more capacitance into the same case and are used on supply rails and on signal paths where a 15 % drift is acceptable.
The number on the label is not the capacitance the board sees. A Class II part loses a large share of its value as the DC voltage across it rises, and the loss depends on case size, dielectric and the thickness of the ceramic layers. A 0603 X7R part marked 10 uF at 6.3 V will hold far less than 10 uF at 6 V, which is why the effective value at the rail voltage is what we quote alongside the marked value.
Voltage rating and case size move together. A 0.1 uF part at 50 V fits a 0603 case, the same value at 500 V needs a 1812 case, and at 1 kV to 2 kV the ceramic layer count and the termination construction change again. The table below lists the parts we quote most often, from 0603 decoupling parts to 1812 high voltage parts used in snubbers and in input filters.
Key Specifications
| Parameter | C0G / NP0, Class I | X7R, Class II | X5R, Class II |
|---|---|---|---|
| Capacitance drift over temperature | 0 plus or minus 30 ppm per C | plus or minus 15 % from -55 C to +125 C | plus or minus 15 % from -55 C to +85 C |
| Drift over applied DC voltage | negligible | significant, value falls as voltage rises | significant, value falls as voltage rises |
| Typical values in 0603 to 1812 | 1 pF to 0.1 uF | 1 nF to 22 uF | 1 nF to 22 uF |
| Aging | none | about 3 % per decade hour | about 3 % per decade hour |
| Dissipation factor | very low, high Q | about 2.5 % to 3 % max | about 3 % to 5 % max |
| Best use | filters, matching, timing, snubbers | decoupling, bulk on a rail, general purpose | dense bulk on a low voltage rail |
| High voltage parts | available to 2 kV in 1812 | available to 2 kV in 1812 | not usual above 50 V |
Included Models and Order Codes
The table lists the parts we quote most often. Case size, capacitance, voltage rating and dielectric are taken from the maker data sheet for each part number; where a part carries an automotive qualification, that is noted in the text below the table rather than in a separate column.
| Part Number | Case | Capacitance | Voltage | Dielectric | Tolerance |
|---|---|---|---|---|---|
| GRM188R71H104KA93D | 0603 | 0.1 uF | 50 V | X7R | ±10% |
| CL10B104KB8NNNC | 0603 | 0.1 uF | 50 V | X7R | ±10% |
| C1608X7R1H104K080AA | 0603 | 0.1 uF | 50 V | X7R | ±10% |
| GRM31CR71H225KA88L | 1206 | 2.2 uF | 50 V | X7R | ±10% |
| CL31B106KBHNNNE | 1206 | 10 uF | 50 V | X7R | ±10% |
| C1812C104K2RACTU | 1812 | 0.1 uF | 200 V | X7R | ±10% |
| C1812C104KCRACAUTO | 1812 | 0.1 uF | 500 V | X7R | ±10% |
| C1812C104KDRACTU | 1812 | 0.1 uF | 1 kV | X7R | ±10% |
| C1812C102KGRACAUTO | 1812 | 1 nF | 2 kV | X7R | ±10% |
| C1812C104J1GACTU | 1812 | 0.1 uF | 100 V | C0G / NP0 | ±5% |
Key Features
Dielectric first, value second – the same capacitance in C0G and in X7R behaves like two different parts. C0G is chosen where the value has to hold across temperature and voltage, X7R where board area matters more than drift.
DC bias measured, not assumed – on a 0603 X7R part the effective capacitance at the working voltage can be a fraction of the marked value, so the bias curve from the data sheet is quoted with the part on any rail above 3.3 V.
Voltage margin at the rail – a 50 V part on a 48 V rail and a 100 V part on a 48 V rail are both used, and the choice follows the transient the rail sees, the derating rule of the customer and the space available for a larger case.
High voltage in 1812 – 0.1 uF at 500 V, 1 kV and 2 kV is available in the 1812 case, which is the size most input filters and snubbers are laid out for. The 1 nF 2 kV part is used where the highest voltage stands off across the ceramic.
Aging and soldering – Class II parts lose about 3 % of their value per decade hour and are restored by the soldering heat, so the value is measured after the reflow the board actually sees rather than on arrival.
Automotive qualified options – parts with an AEC-Q200 qualification are available in the same case sizes for boards that carry an automotive requirement, including the 500 V and 2 kV 1812 parts.
Tape and reel to the line – all parts on this page ship on 180 mm or 330 mm reels with the piece count stated, so the SMT line is not stopped by a partial reel of a part that is used in one place on the board.
Applications
These parts are quoted for boards that mix RF, digital and power on one assembly, typically where: These parts land on the same assembly as the rest of the bill of materials, so they are quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.
RF matching and coupling – a C0G part holds its value from the tuning bench to the temperature chamber, which is why matching networks and interstage coupling on a radio board are built with Class I parts and not with X7R.
Supply rail decoupling – a 1206 X7R 10 uF part next to a regulator and a row of 0603 0.1 uF parts along the rail is the usual pair, and the quantity of the small parts follows the number of power pins rather than the total capacitance.
Input filter and snubber – a 1812 part rated 1 kV or 2 kV stands off the transient on an AC input or across a switching device, where a 50 V part in the same capacitance would break down on the first surge.
Sourcing and Cross-Reference
A ceramic capacitor is the easiest part on a bill of materials to cross and the easiest one to cross badly. Two parts with the same case size, the same capacitance and the same voltage can differ in dielectric, in thickness, in termination material and in DC bias behaviour, and a substitution that ignores the dielectric turns a stable filter into a drifting one.
Our check runs on four fields: dielectric, voltage rating, case size and tolerance, then on the bias curve and the operating temperature at the point of use. Where the original part is short, the substitute is chosen at the same or a higher voltage rating in the same case, and where the case has to change, the land pattern change is stated before the part is quoted.
Long life buys and last time buys are handled on the same screen as active stock, and the route for a rail that has gone short is described on BOM shortage recovery. Where the substitute is a different maker with the same footprint, the rules we apply are on pin to pin cross reference.
For volume builds, SUPERB Assembly support covers the reel change plan, the placement of the 1812 high voltage parts and the reflow profile that keeps the ceramic from cracking.
Q: Can you supply a ceramic capacitor that matches the dielectric and the voltage rating of a part that is no longer stocked?
A: Yes. Send the part number, the dielectric, the voltage rating, the case size and the quantity per board, and the SUPERB Tech team will confirm an equivalent on all four fields before quoting.
Why Buyers Source Ceramic Capacitors Through SUPERB
- Dielectric kept intact: a substitute is never offered in a different dielectric without saying so, because that single change moves the value of the part on the board.
- Bias curve with the quote: the effective capacitance at the rail voltage is quoted for Class II parts, so the rail is not built around a marked value that the part does not deliver.
- Voltage rating never reduced: the replacement is quoted at the same or a higher voltage rating, and any change of case size is stated with the land pattern it needs.
- Mixed bills handled together: the small decoupling parts, the 1812 high voltage parts and the RF C0G parts are quoted on one sheet, which keeps the line item count on the purchase order down.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, Common mode chokes and power inductors, TVS and ESD protection diodes, BOM shortage recovery, Pin to pin cross reference.