Optical Windows and Sapphire Discs for Detector Ports
Product Specifications
Product Overview
A window looks like the simplest part on an analyser and is often the one that limits the reading. It has to keep the sample on one side and the detector on the other, pass the band the instrument uses, and not add a wedge or a wavefront error that shifts the image. When a channel loses throughput after a cleaning cycle, a scratched or hazed window is usually the cause rather than the lamp.
Substrate choice follows the band and the environment. UV fused silica transmits from 185 nm to about 2.1 um and is the default for photometric instruments; N-BK7 covers the visible at lower cost; sapphire gives a hard surface for ports that are cleaned often or exposed to abrasive slurry, and it also takes heat better than glass. Thickness then follows the pressure and the sealing method: a 1.0 mm disc is used where space is tight, a 5.0 mm disc where the port carries pressure or a retaining ring.
Coating is the third decision. An uncoated surface loses about 4% per face by reflection, and on a two window path that is close to 16% of the light. The four broadband AR bands listed below bring average reflectance below 0.5% inside the coated range, which is why the coating band has to be matched to the channel rather than chosen by size.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Substrates | UV fused silica, N-BK7, sapphire | Selected by band and by wear |
| Uncoated transmission | 185 nm to 2.1 um | UV fused silica |
| Diameters | 12.7 mm, 25.4 mm, 38.1 mm, 50.8 mm | Plus 25 x 36 mm rectangular |
| Thickness | 1.0 mm, 3.0 mm, 4.04 mm, 5.0 mm, 12.0 mm | Depends on size and pressure |
| Diameter tolerance | +0.0 / -0.2 mm | Rectangular parts +/- 0.1 mm |
| Thickness tolerance | +/- 0.1 mm to +/- 0.3 mm | Stated per part |
| Clear aperture | 90% or more of diameter | 22.86 mm on a 1 inch window |
| AR coating bands | 245-400, 350-700, 650-1050, 1050-1700 nm | Average reflectance below 0.5% |
| Sapphire thickness range | 3.0 mm and 5.0 mm | 1 inch and half inch bodies |
| Edge finish | Fine ground, uncoated edges | Held in a retaining ring or bonded in |
Included Models and Order Codes
Windows are listed by substrate and size, with thickness in the part description because two windows of the same diameter can be a 1.0 mm disc for a low pressure port or a 5.0 mm disc for a clamped one. The AR suffix follows the same convention across the range, so a 1 inch UV fused silica window is available in each of the four bands by changing the suffix.
| Part Number | Substrate | Diameter | Thickness | Coating | Use |
|---|---|---|---|---|---|
| WG40530 | UV fused silica | 12.7 mm | 3.0 mm | Uncoated or AR | Small detector port |
| WG41010 | UV fused silica | 25.4 mm | 1.0 mm | Uncoated or AR | Tight spaces, low pressure |
| WG41050 | UV fused silica | 25.4 mm | 5.0 mm | Uncoated or AR | Clamped sample port |
| WG41010R | UV fused silica | 25 x 36 mm | 1.0 mm | Uncoated or AR | Rectangular aperture |
| WG42012 | UV fused silica | 50.8 mm | 12.0 mm | Uncoated or AR | Large view port |
| WG10530 | N-BK7 | 12.7 mm | 3.0 mm | Uncoated or AR | Visible only |
| WG11050 | N-BK7 | 25.4 mm | 5.0 mm | Uncoated or AR | Visible, cost sensitive |
| WG30530 | Sapphire | 12.7 mm | 3.0 mm | Uncoated or AR | Abrasive sample |
| WG31050 | Sapphire | 25.4 mm | 5.0 mm | Uncoated or AR | Abrasive, hot port |
| 44-909 | Sapphire | 25.4 mm | 1.0 mm | Uncoated | Thin sapphire disc |
| 21-060 | Sapphire | 25.0 mm | 1.0 mm | BBAR 2000 to 5000 nm | Mid infrared port |
Key Features
Three substrates – silica for UV to NIR, N-BK7 for the visible and sapphire where the port is cleaned often
Thickness from 1.0 mm – a thin disc fits a short optical path without moving the focal plane
Tolerances stated – diameter, thickness and clear aperture are given per part so a retaining ring can be sized
Four AR bands – 245-400, 350-700, 650-1050 and 1050-1700 nm cover the bands used in photometric instruments
Sapphire for wear – a hard surface resists the scratching that haze a glass window after repeated cleaning
Rectangular option – a 25 x 36 mm window matches the aperture of a plate splitter or a slit block
Cleanable faces – coated faces can be wiped with solvent, unlike a soft coated filter
Mid infrared sapphire – the BBAR option carries a sapphire disc into the 2 to 5 um range
Applications
A window is selected by what it has to keep apart and what band it has to pass.
Detector and photometer ports – a silica window seals the detector housing while passing the visible and UV bands
Sample cells and flow housings – a thin disc closes a flow cell without adding to the optical path
Process and slurry lines – a sapphire disc survives abrasive sample and repeated cleaning cycles
Windows and discs for these ports are supplied by the same SUPERB PCB and SUPERB PCBA teams that build the detector boards behind them.
Sourcing and Cross-Reference
Windows are usually replaced because of surface damage, not because the instrument changed. The replacement has to match diameter, thickness and coating, and the thickness matters as much as the diameter: a 1.0 mm disc where a 5.0 mm window was fitted moves the focal plane and shows up as a focus error rather than as a transmission loss.
For a UV channel the substrate and the coating both count. N-BK7 falls away below 350 nm, so a window that reads well in the visible can block the UV end of the same instrument. We confirm the channel band before quoting a substrate, and the AR band is matched to the same range.
Where the port is cleaned with a wipe or carries abrasive sample, sapphire is the cheaper answer over the life of the instrument even though the disc costs more. Both the glass and the sapphire versions are quoted in the same sizes, so the choice can be made on the line without changing the housing.
Detector housings that carry a window and a preamp board are assembled through SUPERB Assembly.
Q: Can you match a window on thickness as well as diameter, so the focal plane does not move?
A: Yes. SUPERB Tech confirms diameter, thickness and coating band against the original window before quoting.
Why Choose SUPERB for Optical Windows
- Thickness matched: the disc is quoted on thickness as well as diameter, so the focal plane stays where it was
- Band checked first: substrate and AR band are confirmed against the channel before a part is proposed
- Sapphire held in the same sizes: a worn glass window can be upgraded without changing the housing
- Tolerances given: clear aperture and edge tolerances are stated so a retaining ring can be sized from the page
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Lenses and Mirrors for Optical Benches, Quartz Flow Cells and Cuvettes, Flow Cell Holders and Cuvette Changers, Dichroic Filters and Beam Splitters, Photodiode Arrays and Detector Modules, Neutral Density Filters and Reference Standards.