Contact Us
  • Home
  • COMPONENTS
  • Flow Cell Holders and Cuvette Changers for Photometric Instruments

Flow Cell Holders and Cuvette Changers for Photometric Instruments

A photometer is only as repeatable as the cell holder. The cell has to sit at the same height, at the same angle and at the same temperature for every reading, and a holder that allows a millimetre of play shows up as a drift in absorbance. This page covers single, twin and six cell holders, Peltier controlled blocks, fiber coupled external holders and the flow cells that fit them. Path length runs from 0.1 to 50 mm, cell volume from 6 microlitres to 3300 microlitres, and the beam height is given as 8.5 or 15 mm so a holder is matched to the instrument. Spacers, stir bars, purge kits and replacement cell holders are listed with the holder, because a 1 mm cell in a 10 mm block needs the spacer as much as the block.
quote now

Product Specifications

Product Overview

A cell holder does three jobs: it locates the cell in the beam, it controls the temperature, and it keeps the cell clean and dry between readings. The first job is mechanical. A 10 mm cell sits in a block with a fixed stop, and the beam height is set at 8.5 or 15 mm depending on the instrument. If the holder allows the cell to tilt, the path length through the liquid changes and the absorbance changes with it, which is why a holder with a spring or a screw clamp is used rather than a simple slot.

The second job is thermal. A Peltier block holds a cell between roughly -5 and 110 C, and the useful figure is not the range but the stability: a block that holds 0.02 C over a ten minute reading gives a repeatable absorbance, while a block that drifts a tenth of a degree moves the reading on a temperature sensitive reaction. For kinetics and for anything near a melting point, the block, the controller and the stir bar are one system, and the stir bar is not optional, because a cell with a temperature gradient across it reads the average of the gradient.

The third job is the flow path. A flow cell turns the holder into a flow injection detector, and the numbers that matter are the cell volume and the swept path. A 10 mm cell with a 390 microlitre volume is a standard for a benchtop spectrophotometer but is too large for a 1 mm column, where a cell of 18 or 80 microlitres is the right size. The connector matters as well: an M6 screw port with a 1.9 mm outside diameter FEP tube is a different fitting from a 1/4-28 flat bottom port, and the two do not seal into each other.

Changers add the fourth job, which is throughput. A six cell Peltier changer presents six 10 mm cells to the same beam in sequence, with the same temperature and the same purge, so a batch of six samples is read without opening the sample compartment. The trade is that each position has to be mechanically repeatable, and a changer that is a few tenths of a millimetre out between positions shows up as a position to position offset. That offset is measured with the same cell in all six positions, not with six different cells.

Key Specifications

ParameterValueNote
Cell format10 x 10 mm standard, 12.5 x 12.5 mm outer on the Hellma flow cellsthe outside dimension sets the block, the path sets the reading
Path length0.1, 0.2, 0.5, 1, 2, 5, 10 and 50 mmshorter paths need a spacer in a 10 mm block
Cell volume6.2 microlitre at 0.1 mm to 3300 microlitre at 10 mmvolume follows path length and aperture
Beam height, Z8.5 mm and 15 mmthe two common instrument heights
Aperturefrom 1.5 mm round to 11 x 3.5 mm rectangularthe aperture sets stray light and the minimum volume
Positions1, 2 in a twin holder, 6 in a changera changer needs position to position repeatability
Peltier range, PIKE holders-5 to 110 Cwith the matching controller and liquid recirculator
Peltier range, six cell changer-20 to 110 Ccontinuous ramp, N2 purge and stirring at every position
Temperature precision0.02 C on a single cell Peltier unitthe figure that matters for kinetics
Stirringmagnetic stir bar 6.35 mm long x 3 mm diameterfits inside a 10 mm cell
Fiber couplingexternal holder with SMA collimators, two fiber cablesfor a measurement away from the instrument
Flow cell connectionsM6 x 1 screw ports with 1.9 mm OD, 1.1 mm ID FEP tube, 500 mm longa 1/4-28 port is a different fitting
PurgeN2 purge on the six cell holderkeeps condensation off a cell below ambient
Materialsanodised aluminium block, quartz or optical glass cellquartz for 200 to 2500 nm, glass for the visible range

Included Models and Order Codes

The table is split between holders and changers, because they are bought for different reasons. A single holder is bought to replace a worn block or to add temperature control; a changer is bought for throughput. The cell numbers are on the second table, since the cell and the holder are usually replaced on different schedules.

PartTypePositionsTemperatureBeam or fittingNote
013-000-71Cell holder for type 106 demountable cells1ambient10 mm blockthe holder is ordered separately from the cell
020-001-761Cell holder for type 124 and 201/202 cells1ambientcircular cellfor cylindrical and demountable cells
013-101-71Aluminium spacer, 1 mmnot applicableambientfits a 10 mm blockputs a 1 mm cell at the right height
013-102-71Aluminium spacer, 2 mmnot applicableambientfits a 10 mm block2 mm path in a 10 mm block
013-105-71Aluminium spacer, 5 mmnot applicableambientfits a 10 mm block5 mm path in a 10 mm block
325.000CleanAssist plastic holder4ambient10 mm cellsholds four cells for cleaning and drying
171-70XXXPeltier cell holder, single1-5 to 110 C8.5 or 15 mm Z heightXXX is the instrument code, controller required
171-80XXXPeltier cell holder, twin2-5 to 110 C8.5 or 15 mm Z heightsingle and dual beam instruments
076-1510Temperature control module, single channelnot applicablereads the block RTDUSB and LCDone module per holder
076-1515Temperature control module, dual channelnot applicablereads two blocksUSB and LCDfor the twin holder
162-1201Spacer, 1 mm pathnot applicableambientPeltier holderwith the 162-1202 and 162-1205 set
162-1202Spacer, 2 mm pathnot applicableambientPeltier holdersame set
162-1205Spacer, 5 mm pathnot applicableambientPeltier holdersame set
162-1905Micro stir barnot applicableambient6.35 mm x 3 mmfits a 10 mm cell
170-1100Liquid recirculatornot applicableheat sink for the Peltierhose to the holderrequired for operation below ambient
CS/PC6Six cell Peltier autochanger6-20 to 110 C10 x 10 mm cellsN2 purge and stirring at every position
CS/SP6Spacer kit for CS/PC6not applicableambientshorter path cellslets a 1 or 5 mm cell sit in the changer

Flow Cells That Fit These Holders

A flow cell is ordered by path length, volume and connector, and the volume is what decides whether it suits a column. The table gives the maker figures for the cell body, so a cell is matched to the holder and to the flow before it is ordered.

CellPath lengthVolumeApertureOutside sizeNote
176.700-QS, 5 mm5 mm195 microlitre11 x 3.5 mm35 x 12.5 x 12.5 mmM6 ports, FEP tube fitted
176.700-QS, 10 mm10 mm390 microlitre11 x 3.5 mm35 x 12.5 x 12.5 mmthe standard flow cell for a benchtop unit
176.700-QS, 50 mm50 mm1950 microlitre11 x 3.5 mm35 x 12.5 x 52.5 mmlong path for low concentration work
178.710-QS10 mm80 microlitre3 mm round35 x 12.5 x 12.5 mmnarrow aperture, lower volume
178.712-QS10 mm18 microlitre1.5 mm round35 x 12.5 x 12.5 mmfor a 1 mm column
170.700-QS, 0.1 mm0.1 mm6.2 microlitre17.5 x 3.5 mm35 x 12.5 x 12.5 mmhighest absorbance, thinnest path
170.700-QS, 1 mm1 mm62 microlitre17.5 x 3.5 mm35 x 12.5 x 12.5 mmconcentrated samples
176.760-QS5 and 10 mm550 microlitre11 x 6 or 11 x 5 mm35 x 12.5 x 12.5 mmtwo path lengths in one cell
176.762-QS1.5 and 3 mm50 microlitre11 x 2.5 or 11 x 1.5 mm35 x 12.5 x 12.5 mmsmallest dual path cell
176.765-QS1 and 10 mm110 microlitre11 x 6 or 11 x 1 mm35 x 12.5 x 12.5 mmturns 90 degrees to change path, tubes stay connected

Key Features

Holders and changers separated – a single holder is bought to replace a worn block, a six cell changer is bought for throughput, and the two are not priced or specified the same way

Beam height 8.5 mm and 15 mm – the two common instrument heights are named on every holder, so a holder is not matched on cell size alone

Peltier blocks from -5 to 110 C – with the controller, the stir bar and the recirculator listed as one system

Six cell changer with purge and stirring – six 10 mm cells at the same temperature, which is what a batch of six samples needs

Spacers for 1, 2 and 5 mm cells – a short path cell sits correctly in a 10 mm block instead of resting on the bottom

Fiber coupled external holder – SMA collimators and two fibers move the measurement to a fume hood without moving the instrument

Flow cells from 6.2 to 3300 microlitre – 18 microlitre for a 1 mm column and 390 microlitre for a benchtop unit, so the cell is chosen against the column

M6 ports with FEP tube – the fitting is named with the cell, because a 1/4-28 port will not seal into an M6 thread

Applications

These holders sit between the light source and the detector, in three settings that put different demands on the block.

Pharmaceutical dissolution testing – a six cell changer with a 5 mm or 10 mm flow cell reads six vessels in sequence. The path length is chosen for the concentration, and the purge keeps condensation off the cell when the bath runs at 37 C in a cold room.

Enzyme kinetics – a single Peltier holder with a stir bar holds one cell at 37 C for a ten minute run. The temperature precision matters more than the range, because the reaction rate changes by about seven percent per degree for a typical enzyme.

Process photometry on a flow line – a flow cell with an 80 microlitre volume sits after a debubbler and before the detector. The swept volume has to be small enough not to broaden a peak, and the connector has to match the 1/16 in tubing on the line.

The detector boards behind these cells are the kind of build SUPERB PCB and SUPERB PCBA programmes cover, from the photodiode front end to the lamp drive.

Sourcing and Cross-Reference

A holder is ordered by instrument, cell format and beam height, and the instrument code is the field that decides the part. A Peltier holder for one spectrophotometer does not fit another even when the cell is the same 10 mm cell, because the block height and the mounting screws differ. We ask for the instrument model and the existing holder number before naming a part.

Where a holder is no longer supplied, the substitute is chosen on the cell format and the beam height first and on the temperature range second. A holder that fits the cell but sits 3 mm lower moves the beam off the aperture and the reading falls without any fault code. Where no equivalent exists, we say so rather than shipping a block that needs a machined adapter.

Flow cells are a wear item on a process line. The cell window etches, the port thread wears and the volume grows with a repaired connector. A replacement cell is matched on path length, volume and port, and where the original cell is a two path length type, the replacement is chosen so the tubes do not have to be re routed.

Where an instrument is assembled with its cell changer and flow cell, the set is picked together, which is how SUPERB Assembly ships an optics module.

Q: Can you supply a Peltier cell holder for an instrument whose original holder is discontinued?

A: SUPERB Tech can confirm the instrument code, the beam height and the cell format against the old holder before the order is placed.

Why Buy Cell Holders from SUPERB

  1. Instrument code confirmed first: the holder is matched to the spectrophotometer, not only to the cell, because the block height and the mounting differ
  2. Cell and holder quoted together: the path length, volume and port are checked as a set, which is what avoids a cell that fits the block but not the flow
  3. Spacers and stir bars on the same list: a 1 mm cell and a 10 mm block are supplied as a working pair
  4. Peltier system complete: holder, controller, recirculator and stir bar are named together, so a temperature controlled cell is not ordered in three parts
  5. Maker part number on the delivery file: the holder, the cell and the spacer are written down, so the next replacement is the same part

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Quartz Flow Cells and Cuvettes for Photometric Instruments, Bandpass and Interference Filters for Photometric Channels, UV and Visible LED Sources for Photometric Detection, Lamp Housings and Shutters for Photometric Instruments, Turbidity and Photometric Detector Modules for Water Analysis, Component Lead Time Solutions.

Actual product photos available on request