Optical Filter Mounts and Lens Holders
Product Specifications
Product Overview
A mount is a mechanical decision that shows up as an optical error. The optic has to sit square to the beam, at a known height above the table, and it has to stay there when a filter is changed next to it. That is why the thread standard matters more than the brand: SM05, SM1 and SM2 threads at 0.535, 1.035 and 2.035 inch are what let a lens tube, a filter holder and a cage plate from three suppliers fit together on one bench.
Fixed holders cover most of the work. A retaining ring traps the optic against a machined lip, and the clear aperture is slightly smaller than the optic, so a 25.4 mm lens sits in a 22.9 mm opening. The maximum thickness is the number that catches people out: a 7.1 mm limit fits a plano convex singlet but not a cemented doublet, and the answer is either a deeper holder or a lens tube in front of it.
The other half of this family is about access. A drop in filter holder lets a 25.4 mm filter be squeezed into a spring clamp and removed again without touching the rest of the setup, which is what a filter wheel cannot do when only one position changes. A kinematic mount adds two adjusters for tip and tilt, and a rotation mount adds a graduated ring for polarisers and wave plates. Each step buys a degree of freedom and costs stability, so the plain holder is still the right answer wherever nothing has to move.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Optic diameters | 12.7, 25.4 and 50.8 mm, plus 2 to 10 mm adapters | Round optics, square filters in the drop in holders |
| Thread standards | SM05 0.535-40, SM1 1.035-40, SM2 2.035-40 | External and internal versions on the same family |
| Max optic thickness | 5.0 mm at 12.7 mm, 7.1 mm at 25.4 mm, 9.1 mm at 50.8 mm | Thin optic cells reach 3.5 mm and stop there |
| Clear aperture | 11.0, 22.9 and 48.5 mm | Measured without a retaining ring |
| Optical axis height | 16.0, 22.1 and 34.5 mm above the post | Newport A line holders sit at 25.4 and 31.8 mm |
| Post mounting | 8-32, M4 and M6 taps and counterbores | Right or left handed orientation on kinematic mounts |
| Kinematic range | Plus or minus 4 degrees at 25.4 mm, plus or minus 3 degrees at 50.8 mm | Two or three adjusters |
| Adjuster resolution | 8 mrad (0.5 degree) per turn at 25.4 mm, 5 mrad at 50.8 mm | 1/4-80 threads |
| Rotation | 360 degrees continuous with 2 degree graduations | Locking screw on the rotation ring |
| Drop in filter holder | 25.4 mm round or square, up to 5 mm thick | Spring loaded v groove clamp |
| Filter mount inside a tube | Unmounted up to 3.5 mm, mounted 3.5 to 6.3 mm | Clear aperture 21 mm, body 33.3 mm OD |
| Retaining rings | SM05RR, SM1RR, SM2RR | Included with most holders, sold separately for some |
Included Models and Order Codes
The table runs from the plainest part to the most adjustable. The first block is fixed holders in three sizes, the second is filter holders that take a filter in and out without tools, and the third is kinematic and rotation mounts where alignment has to be trimmed after assembly. Newport A line holders are listed at the end because their 31.8 mm axis height is fixed and does not match the Thorlabs 22.1 mm.
| Part Number | Optic Size | Max Thickness | Clear Aperture | Axis Height | Mounting | Function |
|---|---|---|---|---|---|---|
| LMR05(/M) | 12.7 mm | 5.0 mm | 11.0 mm | 16.0 mm | 8-32 or M4 tap | Fixed holder, SM05 thread |
| LMR1(/M) | 25.4 mm | 7.1 mm | 22.9 mm | 22.1 mm | 8-32 or M4 tap | Fixed holder, SM1 thread |
| LMR1S(/M) | 25.4 mm | 7.1 mm | 23.0 mm | 22.1 mm | 8-32 or M4 tap | Fixed holder, internal and external SM1 |
| LMR2S(/M) | 50.8 mm | 9.1 mm | 48.5 mm | 34.5 mm | 8-32 or M4 tap | Fixed holder, internal and external SM2 |
| SMR1(/M) | 25.4 mm | 6.1 mm | 25.6 mm | 22.1 mm | 8-32 or M4 tap | Fixed holder, ring sold separately |
| SM1QU | 25.4 mm unmounted filter | 3.5 mm | 21 mm | In line | Fits an SM1 lens tube | Drop in filter mount, 33.3 mm body |
| SM1QP | 25.4 mm mounted filter | 3.5 to 6.3 mm | 21 mm | In line | Fits an SM1 lens tube | Drop in filter mount for mounted filters |
| KM100 | 25.4 mm | 3 mm minimum | Optic bore | 22.1 mm nominal | 8-32 or M4 counterbore | Kinematic, plus or minus 4 degrees |
| KM100T | 25.4 mm | 3.5 mm | Optic bore | 22.1 mm nominal | 8-32 or M4 counterbore | Kinematic cell for thin optics |
| KM100CP(/M) | 25.4 mm | 3 mm minimum | Optic bore | Centred on the post | 8-32 or M4 threaded | Rear loaded kinematic mount |
| KM200 | 50.8 mm | 4 mm minimum | Optic bore | 39.6 mm | 8-32 or M4 counterbore | Kinematic, plus or minus 3 degrees |
| KS1RS | 25.4 mm | 11.9 mm | Optic bore | 22.1 mm nominal | 8-32 or M4 counterbore | Kinematic plus 360 degree rotation |
| KC1T(/M) | 25.4 mm | 5.8 mm | Optic bore | Cage centred | 30 mm cage or post | Three adjuster kinematic cell |
| LMRA5 | 5 mm optic | 2.2 mm | 3.8 mm | In an SM05 mount | SM05 bore | Adapter for small optics |
| LMRA10 | 10 mm optic | 2.5 mm | 8.8 mm | In an SM05 mount | SM05 bore | Adapter, 18 mm outer diameter |
| LH-1A | 25.4 mm | 7 mm edge | 22.9 mm | 31.8 mm | 8-32 tap | Newport A line fixed holder |
| M-LH-1A | 25.4 mm | 7 mm edge | 22.9 mm | 31.8 mm | M4 tap | Metric version of the same holder |
| LH-0.5A | 12.7 mm | Edge thin optic | 10.9 mm | 25.4 mm | M4 tap | Newport small holder |
| LH-2A | 50.8 mm | Edge thin optic | 47.5 mm | 44.5 mm | M4 tap | Newport 2 in holder |
| FH-1S | 25.4 mm round or square filter | 5 mm | Filter face | Not applicable | 8-32 and M4 | Drop in spring clamp filter holder |
Key Features
One thread family – SM05, SM1 and SM2 bores take lens tubes, cage plates and adapters without an extra ring
Clear aperture stated – 22.9 mm on a 25.4 mm holder is quoted, so a lens is not ordered that overfills the opening
Thickness limit per part – 7.1 mm on LMR1 and 3.5 mm on KM100T, which decides between a holder and a tube
Filters changed without tools – a spring clamp or a drop in cell takes a filter out while the rest of the bench stays aligned
Kinematic when it is needed – plus or minus 4 degrees at 25.4 mm for beam steering, with the plain holder kept everywhere else
Rotation for polarisers – a graduated ring with a locking screw, 2 degrees per division on the KS1RS
Applications
These parts are bought with the optic, not after it, because the holder sets the thickness, the height and the thread that everything downstream has to match.
Spectrometer front ends – SM1 holders and drop in filter cells in front of a slit, with the filter changed between methods
Machine vision filters – 25.4 mm square filters in a spring clamp holder on a camera lens, swapped between bandpass ranges
Laser beam steering – a kinematic 25.4 mm mount on a post, adjusted after the laser is on and then locked
Mounts and holders ship alongside SUPERB PCB and SUPERB PCBA work when an instrument build moves from the board to the optics.
Sourcing and Cross-Reference
The two numbers worth checking before an order are the optic thickness and the axis height. A holder that takes a 7.1 mm optic will not close on a 9 mm mounted filter, and a 22.1 mm axis height against a 31.8 mm holder in the same bench leaves a step that has to be shimmed. We quote the height with the part so the bench can be laid out on paper first.
Adapters are the quiet cost. A 5 mm or 10 mm optic needs an SM05 adapter before it can sit in a standard holder, and a 50.8 mm optic needs SM2 parts all the way along the path. Mixing one size into a bench built on another size costs more in adapters than the larger holder would have cost, which is worth saying before a drawing is fixed.
For filter work, the choice is between a holder and a wheel. A wheel changes position by motor or by hand but cannot take a filter outside its carrier, and a drop in holder takes any 25.4 mm filter at once. Where a method needs three fixed ranges at speed, we quote the wheel, and where it needs one filter changed between samples, the spring clamp is cheaper and faster.
Optical kits for a new instrument are packed through SUPERB Assembly, so each holder arrives with its retaining ring and label in one bag.
Q: Can you supply a 25.4 mm kinematic mount together with a drop in filter holder that fits the same SM1 thread?
A: Yes. SUPERB Tech quotes the mount, the retaining ring and any adapter together, and states the optic thickness it closes on before the order is placed.
Why Choose SUPERB for Mounts and Filter Holders
- Threads and heights on the page: SM05, SM1 and SM2 parts are listed with the axis height that goes with them
- Thickness limits stated: each holder names the thickest optic it closes on, so a mounted filter is not ordered blind
- Adapters for small optics: 5 and 10 mm adapters listed with the holders they fit, instead of being found later
- Two maker families: Thorlabs and Newport A line holders quoted side by side when a bench already uses one height
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Lenses and Mirrors for Optical Benches, Filter Wheels and Automated Changers, Dichroic Filters and Beam Splitters, Neutral Density Filters and Photometric Standards, Optical Slits and Apertures, Optical Windows and Sapphire Discs.