Integrating Spheres and Diffuse Reflectance Standards
Product Specifications
Product Overview
An integrating sphere turns direction into quantity. Light entering the sphere bounces until the inside surface is evenly lit, so a detector at any port reads the total flux instead of one reflected angle. That is why a sphere is used for laser power, for the reflectance of a rough or curved sample, and for the colour of a textured surface where a plain probe gives a reading that depends on where it is pointed.
Sphere size, port size and coating are one decision. A 50 mm sphere with an 8 mm port suits a fibre coupled spectrometer and a sample that fills the port; a 200 mm sphere with 12.7 mm ports spreads the light further and gives a more uniform signal on a large detector, at the cost of throughput. A PTFE based wall holds above 98 percent between 400 and 1500 nm and above 95 percent over 250 to 2500 nm, which is enough for most UV to NIR work.
The standard is the other half of the measurement. A reflectance reading is only a ratio against something assumed to be known, and that something is a sintered PTFE tile with a certificate: 99 percent white, or a grey step at 75, 50, 20, 10 or 2 percent to check linearity. The certificate reports the hemispherical reflectance factor every 50 nm from 250 to 2500 nm against a NIST scale, so the calibration chain is stated rather than assumed.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Sphere diameter | 30, 50, 80 mm fibre coupled, 50.8 mm (2 in) bench mount | Labsphere general purpose 1 to 6 in |
| Port diameter | 6 or 8 mm on fibre spheres, 12.7 mm (0.5 in) on 2 in spheres | Port reducers and plugs are separate items |
| Port count | 3 ports at 0, 90 and top, or 4 ports adding 180 | Unused ports closed with a coated plug |
| Wall material | Sintered PTFE, or Spectralon machined body | Spectraflect barium sulphate coating on request |
| Reflectance, Thorlabs 2 in | About 99 percent from 350 to 1500 nm, above 95 percent from 250 to 2500 nm | Wall, not the sample |
| Reflectance, ISP series | Above 98 percent from 400 to 1500 nm, above 95 percent from 250 to 2000 nm | PTFE based diffusing material |
| Detector port | 3 mm recessed port for SM05PD photodiodes | Recess keeps direct light off the active area |
| Thermal limit | Up to 250 C on the 2 in sphere | Coating sets the real limit |
| Laser damage | 2 kW per sq cm continuous, 7 J per sq cm pulsed | At the 2 in sphere port |
| Standard reflectance levels | 2, 5, 10, 20, 25, 40, 50, 60, 75, 80 and 99 percent | Individual tiles or matched sets |
| Standard calibration | 8 degree illumination, hemispherical collection | Reported every 50 nm, 1 nm in the data file |
| Standard sizes | 31.8 mm (1.25 in) and 50.8 mm (2 in) optical surface | Targets from 2 x 2 in to 24 x 24 in |
Included Models and Order Codes
The first table lists the spheres, grouped by the instrument they attach to: 2 in bench spheres with SM05 ports, fibre coupled spheres with SMA 905, and the Labsphere general purpose bodies with three or four ports. The second table lists the standards, where the part number fixes the reflectance level and the size, and the order number fixes the certificate.
| Part Number | Sphere Size | Ports | Coating or Wall | Detector | Interface | Use |
|---|---|---|---|---|---|---|
| IS200 | 50.8 mm (2 in) | 3 at 0, 90, top | PTFE based wall | None | SM05 and 30 mm cage | Laser power and flux |
| IS200-4 | 50.8 mm (2 in) | 4 at 0, 90, 180, top | PTFE based wall | None | SM05 and 30 mm cage | Reflectance with a reference port |
| IS236A | 50.8 mm (2 in) | 3 at 0, 90, top | PTFE based wall | SM05PD1B silicon | SM05 and 30 mm cage | 350 to 1100 nm radiometry |
| IS236A-4 | 50.8 mm (2 in) | 4 at 0, 90, 180, top | PTFE based wall | SM05PD1B silicon | SM05 and 30 mm cage | Two detector comparison |
| IS210C | 50.8 mm (2 in) | 3 at 0, 90, top | PTFE based wall | SM05PD4A InGaAs | SM05 and 30 mm cage | 800 to 1700 nm work |
| ISP-30-6-R | 30 mm | Sample port 6 mm | Sintered PTFE | None | 2 x SMA 905 | Small sample reflectance |
| ISP-50-8-R | 50 mm | Sample port 8 mm | Sintered PTFE | None | 2 x SMA 905 | Fibre coupled reflectance |
| ISP-50-8-R-GT | 50 mm | Sample port 8 mm, gloss trap | Sintered PTFE | None | 2 x SMA 905 | Specular included or excluded |
| ISP-80-8-R | 80 mm | Sample port 8 mm | Sintered PTFE | None | 2 x SMA 905 | Larger or textured samples |
| 3P-GPS-020-SL | 50.8 mm (2 in) | 3 at 0, 90, top | Spectralon | None | 1 in port frames | Colour and radiance work |
| 4P-GPS-020-SL | 50.8 mm (2 in) | 4 at 0, 90, 180, top | Spectralon | None | 1 in port frames | Reference port in use |
| 3P-GPS-020-SL-KIT | 50.8 mm (2 in) | 3 ports with plugs | Spectralon | None | Post and holder included | Bench setup in one order |
| 4P-GPS-020-SL-KIT | 50.8 mm (2 in) | 4 ports with plugs | Spectralon | None | Post and holder included | Lab ready kit |
Diffuse Reflectance Standards and Targets
Every standard carries two numbers: the model, which states the reflectance level and the size, and the order number, which states the certificate. The 1.25 in tiles suit a sphere with an 8 mm port, the 2 in tiles suit a bench instrument, and the 5 to 10 in targets are for camera and imaging work. A set is worth quoting when linearity across the range has to be shown at one time.
| Model | Order Number | Reflectance | Size | Form | Calibration |
|---|---|---|---|---|---|
| SRS-99-010 | AS-01160-060 | 99 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-99-020 | AS-01161-060 | 99 percent | 50.8 mm (2 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-80-010 | AS-01160-160 | 80 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-75-010 | AS-01160-260 | 75 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-60-010 | AS-01160-360 | 60 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-50-010 | AS-01160-460 | 50 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-40-010 | AS-01160-560 | 40 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-20-010 | AS-01160-660 | 20 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-10-010 | AS-01160-760 | 10 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-05-010 | AS-01160-860 | 5 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| SRS-02-010 | AS-01161-960 | 2 percent | 31.8 mm (1.25 in) | Tile in holder | 250 to 2500 nm, every 50 nm |
| RSS-04-010 | AS-01163-060 | 99, 75, 50 and 2 percent | 31.8 mm (1.25 in) | Set of four tiles | 250 to 2500 nm, every 50 nm |
| RSS-08-010 | AS-01163-160 | 99, 80, 60, 40, 20, 10, 5 and 2 percent | 31.8 mm (1.25 in) | Set of eight tiles | 250 to 2500 nm, every 50 nm |
| SRT-99-050 | AA-00821-000 | 99 percent | 127 mm (5 in) | Mounted target | 250 to 2500 nm, every 50 nm |
| SRT-99-100 | AA-00822-000 | 99 percent | 254 mm (10 in) | Mounted target | 250 to 2500 nm, every 50 nm |
| USRT-99-050 | AS-02627-000 | 99 percent | 127 mm (5 in) | Mounted target, uncalibrated | Nominal value only |
Key Features
Ports closed with the same wall – each unused port ships with a plug coated in the sphere material, so the wall stays uniform
Recessed detector port – the photodiode sits behind a 3 mm recess, so a divergent beam cannot reach the active area directly
Three port sizes on one page – 30, 50 and 80 mm fibre spheres plus the 2 in bench sphere, chosen by sample size
Gloss trap option – specular included or excluded with two inserts, which is how colour work is compared between labs
Standards with certificates – reflectance reported every 50 nm from 250 to 2500 nm, traceable to NIST
Sets for linearity – four or eight grey steps in one box, so a whole calibration runs in one session
Applications
A sphere and a standard are bought as a pair: the sphere collects the light and the tile tells the instrument what 100 percent looks like.
Laser and LED power – a 2 in sphere with an SM05PD photodiode, read directly with no lens in front of the detector
Colour of textured surfaces – a 50 mm sphere with an 8 mm port and a 99 percent tile as the white reference
Reflectance of coatings and glass – a four port sphere with the sample at 0 degrees and a reference port at 180 degrees
Spheres and tiles ship alongside SUPERB PCB and SUPERB PCBA work when an instrument build moves from the board to the optics.
Sourcing and Cross-Reference
Sphere quotes are settled by three numbers: inner diameter, port diameter and wall material. The same 2 in body with a Spectralon wall and with a Spectraflect coating differs in reflectance below 400 nm, and a customer moving a validated method cannot swap one for the other without repeating the calibration.
Standards are often ordered a year after the sphere, when the first audit comes. A 99 percent tile drifts slowly but the holder and the certificate matter, so we keep the order number rather than the model in the quotation, and we state whether the tile is calibrated or nominal. An uncalibrated target costs less and is honest for a go or no go check, but it cannot be used to set the scale.
Two practical points decide the size. A tile has to cover the sphere port completely, or light leaks past the edge and the reading falls short; and a tile handled by its face collects skin oil that shows first in the UV. We quote a spare tile with the first order where the method runs daily.
Optical kits for a new instrument are packed through SUPERB Assembly, so each sphere arrives with its plugs, tile and certificate in one box.
Q: Can you supply a 50 mm sphere with an 8 mm port together with a calibrated 99 percent tile of the same size?
A: Yes. SUPERB Tech quotes the sphere and the matching tile together, and states the port diameter and the certificate level on the quotation.
Why Choose SUPERB for Spheres and Reflectance Standards
- Wall material stated per part: PTFE, Spectralon and Spectraflect are separated, because the UV end of the curve depends on it
- Port sizes and plugs together: the quote lists the plugs and reducers the sphere needs, so nothing arrives open
- Certificate named by order number: calibrated and nominal tiles are never mixed on one line
- Sets for linearity: four and eight step sets quoted with the sphere when a method needs a full check
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Neutral Density Filters and Photometric Standards, Reflectance and Transmission Probes, Optical Windows and Sapphire Discs, Photodiode Arrays and Detector Modules, Lenses and Mirrors for Optical Benches, Photomultiplier Tubes and Housings.