Contact Us
  • Home
  • COMPONENTS
  • Compression and Battery Contact Springs for Enclosures

Compression and Battery Contact Springs for Enclosures

A battery contact is a spring, and the pressure it puts on the cell is what keeps the circuit closed through a cold morning and a dropped case. The Keystone contacts here cover A, AA, C, CR2 and 17 to 19 mm cells, in steel with a nickel plate and a spring steel arm. The compression springs run from a 0.5 in free length at 0.68 lb per in to a 1.22 in free length at 134 lb per in, in 302 and 304 stainless. Rate, solid height and maximum load are stated, so the spring is chosen against the space rather than by eye.
quote now

Product Specifications

Product Overview

A battery contact looks like a stamped tab, and it is a spring with a contact face. Its job is to hold a cell against a button with enough pressure that the joint does not open when the case is dropped, the temperature falls or the plastic relaxes over a year. The metal is a nickel plated steel plate, 0.020 in thick on the Keystone parts, with a spring steel arm riveted or formed into it, and the plating is what keeps the contact resistance low at the cell terminal.

The family on this page is split by function rather than by cell size. A negative contact is the spring: it has an arm that bends as the cell is inserted and holds it under compression. A positive contact is the button: a flat or dimpled face that the cell presses against. A dual contact takes the place of a pair and carries both ends for a single cell. The tab and lance versions add a solder tab for a wire and a lance that bites into the moulding to stop the part turning.

Keystone 5220 is the negative spring with a tab and a lance, and it is rated for A, AA, CR2 and 17 mm and 19 mm cells, mounted in the case rather than on the board. Its mating button is 5219, and for two AA cells in series the mating part is the dual contact 5217 or 5218. The 5221 is the solid positive contact, and 5207 is the A cell positive button. The 5211, 5212 and 5210 parts are the left and right hand contacts for a side-by-side pair, which is how a two cell compartment is usually wired.

The operating temperature of the contact is minus 45 C to 85 C, which is set by the plating and the spring steel rather than by the plastic. That range covers an outdoor cabinet and a vehicle, and it is the reason a nickel plated steel contact is used instead of a bare brass tab: brass is a better conductor and a worse spring, and a contact that takes a set at 80 C stops holding the cell.

The second family on this page is the compression spring, and it is a different calculation. A compression spring is chosen by its rate, its free length and its solid height, and the working point is the load at the installed height. A spring with a 58 lb per inch rate compressed by 0.2 in carries about 11.6 lb, and its solid height tells you how far it can go before the coils stack.

The Century Spring parts listed here are all 0.562 in outside diameter in 302 and 304 stainless, which is the size that fits a 9/16 in bore or over a 3/8 in rod. The lightest is S-1459CS at 0.68 lb per in with a 0.5 in free length and a 0.25 lb maximum load; the heaviest is S-1534CS at 134 lb per in with a 1.22 in free length and a 36 lb maximum load. Between them, S-1138CS at 1.8 lb per in, S-1027CS at 11 lb per in and S-22CS at 58 lb per in cover the usual range for a latch return, a contact pressure pad or a cover release.

Two rules decide whether a spring survives. The first is solid height: a spring compressed to its solid height on every cycle takes a set and loses rate, so the working height has to be above it with a margin. The second is the slenderness ratio: when the free length is more than about four times the mean diameter the spring buckles sideways under load, and a spring that buckles in a small compartment rubs on the housing. A guide rod or a closer bore is the fix, not a heavier wire.

Stainless is chosen for the compression springs here because a spring in an enclosure sees condensation and a plated carbon spring eventually shows rust at the coil contact. Stainless is not as strong as music wire for the same wire diameter, so a stainless part is usually one wire size heavier than the carbon part it replaces. Where the load is critical, the stainless part is quoted at its own rate rather than as a like for like swap.

Key Specifications

ParameterValueNotes
Contact materialSteel plate 0.020 in, nickel platedSpring arm in nickel plated spring steel
Contact temperature rangeMinus 45 C to 85 CSet by the plating and the spring steel
Cell sizesA, AA, C, CR2, 17 mm and 19 mmPer part number
Contact typesNegative spring, positive button, dual contact, tab and lanceChosen by the compartment
MountingCase mounting, solder tab for a wire or a boardPer part number
Compression spring material302 and 304 stainless steelClosed and ground ends on most parts
Compression spring outside diameter0.562 inFits a 9/16 in bore
Compression spring free length0.5 in to 1.22 inPer part number
Compression spring rate0.68 lb per in to 134 lb per inLoad is rate times deflection
Maximum load0.25 lb to 36 lbAt the suggested maximum deflection
Solid height0.13 in to 0.61 inWorking height stays above it
EndsClosed and ground, or closedPer part number

Included Models and Order Codes

Battery contacts are listed by function and cell size first, then the compression springs by rate and free length. A contact and a spring are not interchangeable, so the function column is the one to read before the part number.

Part NumberFunctionCell or SizeMaterialMountingNotes
5220Negative spring, tab and lanceA, AA, CR2, 17 mm, 19 mmSteel, nickel plateCaseMates with 5219
5219Positive buttonA, AA, CR2Steel, nickel plateCaseMating button for 5220
5221Positive contact, solidAA and similarSteel, nickel plateCaseSolid button
5218Dual contactTwo AA cellsSteel, nickel plateCaseSeries pair with 5220
5217Dual contactTwo AA cellsSteel, nickel plateCaseAlternative to 5218
5207Positive buttonA cellSteel, nickel plateCaseA cell compartment
5210Side contact, leftAA pairSteel, nickel plateCaseLeft hand of a pair
5211Side contact, rightAA pairSteel, nickel plateCaseRight hand of a pair
5212Side contact, left or rightAA pairSteel, nickel plateCaseEither side
5215ContactC cellSteel, nickel plateCaseC cell compartment
5216ContactC cellSteel, nickel plateCaseC cell compartment
S-1459CSCompression spring0.562 in OD, 0.5 in free length302 and 304 stainlessOver a rod or in a boreRate 0.68 lb per in, max 0.25 lb
S-1138CSCompression spring0.562 in OD, 0.75 in free length302 and 304 stainlessOver a rod or in a boreRate 1.8 lb per in, max 1.1 lb
S-1027CSCompression spring0.562 in OD, 1.0 in free length302 and 304 stainlessOver a rod or in a boreRate 11 lb per in, max 6.7 lb
S-22CSCompression spring0.562 in OD, 0.75 in free length302 and 304 stainlessOver a rod or in a boreRate 58 lb per in, max 14 lb
S-1534CSCompression spring0.562 in OD, 1.22 in free length302 and 304 stainlessOver a rod or in a boreRate 134 lb per in, max 36 lb

Key Features

Function stated before the part number – Negative spring, positive button, dual contact and side contact are separated, because a button cannot do the job of a spring.

Nickel plated steel throughout – A 0.020 in steel plate with a nickel plated spring arm, which holds contact resistance down at the cell terminal.

Range to 85 C – Minus 45 C to 85 C on the contact, which covers a vehicle dash and an outdoor cabinet without the spring taking a set.

Tab and lance versions – A solder tab for a wire and a lance that bites into the moulding, so the contact does not turn when a cell is pushed in.

Rate and free length on every spring – A spring is chosen by rate, free length and solid height, and all three are listed with the part.

Solid height published – 0.13 in to 0.61 in, so the working height can be checked against the compartment before the housing is moulded.

Stainless for a damp enclosure – 302 and 304 stainless coils, which do not rust at the coil contact the way a plated carbon spring does.

Applications

These parts go in battery compartments, latch returns, cover releases and pressure pads, wherever a small spring has to hold a known load in a known space.

Handheld instrument compartments – A 5220 spring with a 5219 button in a moulded AA compartment, with the tab soldered to the lead that leaves the case.

Two cell series packs – A dual contact 5218 with a 5220 spring, so two AA cells sit in series without a wire between them.

Latch and cover returns – An S-22CS or S-1027CS compression spring on a cover release, chosen by the load at the installed height rather than by length.

Pressure pads on a sensor – A light S-1138CS spring holding a board against a housing, where the load has to stay under a pound to avoid stressing the part.

A spring is chosen by the load it has to hold and the space it has to hold it in, and the SUPERB PCB battery compartment drawing fixes both before the contact is ordered. On the SUPERB PCBA route the contacts are fitted to the moulded case after the board is screwed down, because a spring that is already in the compartment catches the board on the way in.

Sourcing and Cross-Reference

A contact is ordered from the compartment rather than from the cell size. The cell and the number of cells set the function, the moulding sets the mounting, and the lead or the board sets whether a tab is needed. Two parts with the same cell size are not interchangeable if one is a spring and the other is a button, and that is the cross reference that most often goes wrong.

A compression spring is ordered with four numbers: outside diameter or bore, free length, rate and the load at the working height. Solid height comes with them because a spring that is compressed to solid loses its rate. When only the space is known, the rate follows from the load and the travel, and the part is chosen from the table rather than from the nearest length.

Where a spring is replaced by a stainless part, the rate is quoted rather than the wire size, because stainless and music wire do not carry the same load at the same diameter. A like for like swap on wire diameter usually comes out softer than the part it replaced, which shows up as a latch that does not hold.

SUPERB Assembly fits a cell to the first housing of a build and checks the contact pressure at both ends, because a spring that is too soft loses contact on a cold morning and a spring that is too stiff cracks the moulding around the tab.

Q: Can you supply 5220 negative contacts with 5219 buttons for an AA compartment, and a stainless compression spring at about 12 lb at the installed height?

A: Send the cell size, the number of cells, the spring travel, the load you need at working height and the space the spring has to fit. The SUPERB Tech desk quotes the contact or the compression spring with its load and its free length, so the housing is moulded once.

Why Buy Springs and Contacts Through SUPERB

  1. Function matched to the compartment: Spring, button, dual and side contacts are separated, so the part that arrives can do the job the drawing asks for.
  2. Loads published, not guessed: Rate, free length, solid height and maximum load are listed for every spring on the page.
  3. Cell sizes grouped with the part: A, AA, C, CR2 and 17 to 19 mm cells are stated against the contact, which is what the moulding has to match.
  4. Stainless options in the same list: A damp enclosure gets a stainless coil without a second supplier and a second lead time.
  5. Small quantities for a service kit: A handful of contacts and springs is quoted as one line, which suits a repair rather than a production run.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Battery Holders and Coin Cell Retainers for Backup Power, Standoffs, Spacers and Mounting Hardware for Board Stacks, Captive Panel Screws and Quarter Turn Fasteners, Anti Vibration Mounts and Rubber Isolators, Test Points and Spring Contacts for Board Probing, BOM Shortage Recovery.