Anti Vibration Mounts and Rubber Isolators
Product Specifications
Product Overview
A resilient mount does not absorb vibration, it separates two masses so that the vibration has to pass through rubber before it reaches the frame. The part is a rubber section bonded to two steel plates, with a thread in each plate. Load it in compression and the rubber deflects, and the deflection is what turns a rigid joint into a filter.
The number that selects the mount is the static load on each point, which is the equipment mass divided by the number of mounts, with an allowance for the centre of gravity. A chassis that weighs 12 kg on four mounts carries 3 kg at each, and on a mount rated 20 lb the rubber sits near its working range. Put the same 12 kg on two mounts and the part has to move up a size, because a bobbin that is loaded past its rated figure compresses to solid and stops isolating.
The second number is the shear limit. A cylindrical mount is built for compression, and the maker's rule is that a shear load should not exceed 20 percent of the axial figure. On a chassis that is mounted on a wall, or on a frame that leans, the load is partly shear, and the mount is chosen against the smaller figure. A bobbin used in tension is not covered at all: the rubber is bonded, not moulded through, and a tensile load pulls the plate off.
The bodies on this page come in four styles. Type T has a male thread at both ends and is the usual part for a chassis that is bolted to a frame on both sides. Type TH has a male thread at one end and a female thread at the other, which is what a panel that is fixed with a screw from the outside needs. Type H has a female thread at both ends, for a mount that is drawn down by a bolt from each side. Type TS has a single male thread and is used as a bumper or an anti skid foot.
The range starts at a 10 mm diameter, 10 mm high body on an M4 thread with a 20 lb axial load and runs to a 100 mm diameter, 55 mm high body on an M16 thread at 2100 lb. The steps are close in the small sizes, 20 lb, 50 lb, 85 lb, 140 lb, 190 lb and 240 lb, and wider above that at 320 lb, 540 lb, 780 lb, 1150 lb and 2100 lb. That gives a choice at almost every chassis weight without going to a custom part.
The standard elastomer is natural rubber at 55 Shore A, with zinc plated steel threads. Natural rubber is the right material for a general machine frame: it has good fatigue life and good rebound. It is not the material for an oil sump, a fuel line or an ozone rich cabinet, where neoprene or nitrile is quoted in the same body. A harder compound carries more load in the same envelope, which is the way to stiffen a mount without changing the drilling.
Deflection is set by the maker at a maximum of 15 percent of the rubber height under the rated vertical load. That figure is what the clearance around a chassis is set by: a 25 mm high body moving 3.75 mm needs that much space before it touches a rail. A mount installed with no clearance bottoms out on the first shock and passes the shock straight into the frame.
Installation matters as much as selection. The mounting holes are deburred, the mount is assembled with a washer under each nut, the thread is not twisted after assembly and the two plates are not forced onto misaligned holes. A mount that is twisted during fitting pre loads the rubber in shear and loses part of its isolation before the equipment is even switched on.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Body style | T, TH, H and TS | Male both ends, male and female, female both ends, bumper |
| Body diameter | 10 mm to 100 mm | Model number gives diameter then height |
| Body height | 8 mm to 55 mm | Rubber height between the plates |
| Thread sizes | M4 x 0.7 to M16 x 2.0 | Zinc plated steel |
| Axial load range | 20 lb to 2100 lb | About 9 kg to 950 kg per mount |
| Elastomer | Natural rubber, 55 Shore A standard | Neoprene and nitrile to order |
| Shear limit | 20 percent of the axial load | Use the smaller figure for a leaning frame |
| Maximum deflection | 15 percent of the rubber height at rated load | Sets the clearance around the chassis |
| Loading direction | Compression only | Not for a tensile load |
| Operating temperature | Natural rubber up to about 65 C | Higher temperature needs another compound |
Included Models and Order Codes
The model number is the body diameter and the body height in millimetres, with the thread added where a size is offered in two threads. Load is the axial figure per mount at the rated deflection.
| Model | Body Diameter | Body Height | Thread | Axial Load | Typical Use |
|---|---|---|---|---|---|
| 10-10 | 10 mm | 10 mm | M4 x 0.7 | 20 lb | Small sensor housing, fan tray |
| 10-15 | 10 mm | 15 mm | M4 x 0.7 | 20 lb | Instrument case on a bracket |
| 15-8 | 15 mm | 8 mm | M4 x 0.7 | 50 lb | Compact power supply |
| 20-15 | 20 mm | 15 mm | M6 x 1.0 | 85 lb | Control panel on a machine frame |
| 25-15 | 25 mm | 15 mm | M6 x 1.0 | 140 lb | Small pump or blower |
| 25-25-M6 | 25 mm | 25 mm | M6 x 1.0 | 140 lb | Cabinet on a vibrating floor |
| 25-25-M8 | 25 mm | 25 mm | M8 x 1.25 | 140 lb | Cabinet with an M8 fixing |
| 30-20 | 30 mm | 20 mm | M8 x 1.25 | 190 lb | Fan and blower set |
| 35-35 | 35 mm | 35 mm | M8 x 1.25 | 240 lb | Compressor skid |
| 40-30-M8 | 40 mm | 30 mm | M8 x 1.25 | 320 lb | Motor on a base frame |
| 40-40-M10 | 40 mm | 40 mm | M10 x 1.5 | 320 lb | Motor with a larger fixing |
| 60-25-M8 | 60 mm | 25 mm | M8 x 1.25 | 780 lb | Generator set, low profile |
| 60-40-M12 | 60 mm | 40 mm | M12 x 1.75 | 780 lb | Generator set with an M12 fixing |
| 100-55 | 100 mm | 55 mm | M16 x 2.0 | 2100 lb | Heavy skid and transformer base |
Key Features
Load per mount, not per machine – The table gives the axial figure for one mount, which is the number a four point layout has to divide the mass by.
Four body styles in one range – Male both ends, male and female, female both ends and a bumper, so the fixing method does not force a different family.
Shear rule stated with the part – Shear is limited to 20 percent of the axial load, which decides a wall mounted chassis before the part is ordered.
Deflection allowance given – 15 percent of the rubber height at rated load, so the clearance around a chassis can be set from the drawing.
Natural rubber at 55 Shore A – A general purpose compound with good fatigue life, with neoprene and nitrile quoted for oil or ozone.
Threads stated per size – M4 to M16 with the pitch, zinc plated, and two thread options on the 25 mm and 40 mm bodies.
Bumper style for a resting panel – The TS body takes the weight of a panel that sits on the mount rather than hanging from it.
Applications
These mounts sit between a chassis and a frame on machines, cabinets and vehicles, wherever a motor, a fan or a road surface is putting energy into the structure.
Machine control cabinets – Four 25 mm or 30 mm bodies under a cabinet on a vibrating floor, loaded in compression with the clearance set from the deflection figure.
Fan and blower assemblies – 30 mm to 40 mm bodies on a blower frame, where the vibration is continuous and the mount has to keep its fatigue life.
Transport and vehicle racks – Smaller 10 mm to 20 mm bodies on a rack that sees road shock, with the shear load checked against the 20 percent rule.
Instrument and test housings – 10 mm bodies on a bench instrument that has to stay level, with a bumper body under a panel that rests on the frame.
A resilient mount is selected by the mass it carries and the frequency it has to isolate, so the load per mount and the rubber hardness are read with the equipment drawing that the SUPERB PCB rack is built to. On the SUPERB PCBA route the mounts are fitted after the chassis is populated, because a rubber bobbin that is already in place takes the weight of the boards while they are being landed.
Sourcing and Cross-Reference
A mount is quoted from three numbers: the mass on each point, the thread, and the direction of the load. Give the mass of the equipment and the number of points and the axial figure follows; give the thread as well and the body is fixed. A quotation that starts from the body size alone usually comes back to the mass, because a mount that is too small bottoms out and one that is too large passes the vibration through.
Where the equipment is mounted on a wall or a sloping frame, part of the load is shear and the mount has to be selected against 20 percent of its axial figure. That is a different part from the one a floor mounted version of the same machine would take, and it is worth stating on the drawing rather than in a note.
For a compound other than natural rubber, the same body is quoted in neoprene or nitrile with the load figure restated, because hardness and rebound differ. Where a part number has been discontinued, the substitute is matched on body diameter, height, thread and axial load together, and we say when the deflection will differ.
SUPERB Assembly loads each mount to its rated figure on a press before the chassis is closed, and checks that the rubber is compressed and not sheared, because a bobbin used sideways carries a fifth of its axial load and sags within a month.
Q: Can you supply four 30 mm cylindrical mounts with an M8 thread for a 60 kg cabinet, and confirm the axial load and the clearance for 15 percent deflection?
A: Send the mass of the equipment, the number of mounting points, the lowest frequency the mount has to isolate above, the thread size and whether the mount is loaded in compression or in shear. The SUPERB Tech desk quotes the bobbin with its axial load and its thread.
Why Buy Isolators Through SUPERB
- Quoted from the mass and the thread: The load per mount and the fixing are read together, so the part is sized to the chassis rather than to the catalogue page.
- Shear and tension rules stated: The 20 percent shear limit and the ban on tensile loading are on the page, which is what a wall mounted chassis needs to know.
- Four styles in one range: The fixing method can change without changing the body, so a change to the bracket does not re-open the mount choice.
- Deflection published: 15 percent of the rubber height at rated load, so the clearance around the chassis is a drawing figure rather than a guess.
- Compound options on the same body: Natural rubber, neoprene and nitrile in the same envelope, for an oil or an ozone environment.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Standoffs, Spacers and Mounting Hardware for Board Stacks, Continuous and Butt Hinges for Enclosure Doors, Enclosure Handles and Corner Guards for Portable Units, Threaded Inserts and Standoff Nuts for Plastic Enclosures, Captive Panel Screws and Quarter Turn Fasteners, BOM Shortage Recovery.