Contact Us
  • Home
  • COMPONENTS
  • Column Ovens and Heater Blocks for HPLC Compartments

Column Ovens and Heater Blocks for HPLC Compartments

Column ovens and heater blocks that hold an HPLC column at temperature. Peltier ovens from 4.0 C to 70.0 C, heating only ovens from 20.0 C to 90.0 C. Aluminium block heaters to 150 C for columns up to 50 cm long. Stability of 0.1 C to 0.2 C, PID control and over temperature protection.
quote now

Product Specifications

Product Overview

Retention time moves with column temperature. A bench that swings two degrees over a shift will drift peaks enough to fail a system suitability check, and the usual fix is not a new pump but a column oven or a heater block that actually holds set point. This page covers both: Peltier chambers that heat and chill a whole compartment, and aluminium blocks that clamp a single column and take it to 150 C.

The two families solve different problems. A Peltier oven is chosen when the method needs sub ambient control, because it can hold 4.0 C to 70.0 C and bring a column back down between runs. A block heater is chosen when the method runs hot, up to 150 C, and when the column is long: the block bodies listed here take columns up to 50 cm and can carry two Rheodyne valves in the heated zone, which removes a cold transfer line.

What decides a replacement is chamber size and control stability, not the outside dimensions. A unit that holds four 30 cm by 1 inch columns cannot be replaced by a single column oven without changing the method, and a block rated to 0.1 C stability cannot be swapped for one that only holds 1 C if the method is sensitive to retention time.

Key Specifications

ParameterValueNotes
Peltier oven range4.0 C to 70.0 CHeating and chilling
Heating only oven range20.0 C to 90.0 CSingle column chamber
Stability+/- 0.1 C to +/- 0.2 CAfter warm up
Accuracy+/- 0.2 CBoth oven families
Chamber uniformity+/- 0.5 CAcross the chamber
Column capacityfour 30 cm x 1 in columnsHigh capacity Peltier oven
Block heater rangeAmbient to 150 CAluminium block bodies
Block element power125 W, 300 W, 500 WOne, four and long column bodies
Block sensor1000 ohm RTDPlatinum resistance sensor
ControlPID with RS232 on the ovensRamp and soak available
Over temperature cut out180 C +/- 10 CIndependent protection

Included Models and Order Codes

The table mixes ovens and blocks because they are ordered for the same slot on the bench. Capacity is given as columns by length, since a unit that holds four 30 cm columns is a different replacement from one that holds a single column, even when the temperature range is identical.

Part NumberTypeTemperature RangeCapacityControlNote
CO20Peltier column oven20.0 C to 90.0 COne column, 30 cm, 1/4 or 3/8 inPID, RTD sensor40 W heater
CO30Peltier column oven4.0 C to 70.0 CFour columns, 30 cm x 1 inPID, RS232100 W Peltier, 230 W max
CH-30Heater block bodyAmbient to 150 COne column up to 1/2 in OD, 30 cmExternal controller125 W element
CH-430Heater block bodyAmbient to 150 CFour columns, 30 cmExternal controller300 W, two valve positions
CH-460Heater block bodyAmbient to 150 CFour columns, up to 50 cmExternal controller500 W element
CH-500Heater and controllerAmbient to 150 CTwo 1/4 in and two 1/8 in blocksBuilt in controller120 V and 240 V versions
500879Replacement blockAmbient to 150 C4 in blocks, pack of twoFits CH-500Spare part
500895Replacement blockAmbient to 150 C1 in blocks, pack of twoFits CH-500Spare part
WAT038039Temperature control systemAmbient to 150 COne heater module plus controllerProgrammableControls three modules
WAT038040Column heater moduleAmbient to 150 CFour columns to 30 cmFrom WAT038039Additional module

Key Features

Sub ambient control – the Peltier chamber holds 4.0 C, which a block heater cannot reach without a chiller

0.1 C stability – retention time stays inside a system suitability window over a full shift

Four column capacity – a high capacity chamber holds four 30 cm columns at one set point

Blocks to 150 C – aluminium bodies take a column well above the range of a Peltier oven

Valve in the heated zone – the four column block has provision for two Rheodyne valves, which removes a cold transfer line

Long column support – one body takes columns up to 50 cm, so a long method does not need a second oven

Replacement blocks – block halves are sold as spares, so a damaged channel does not scrap the controller

Over temperature protection – an independent cut out at 180 C protects the column if a sensor fails

Applications

The choice between a chamber and a block follows the method, not the bench space.

Pharmaceutical method development – sub ambient control holds a method at 4.0 C to 70.0 C through a sequence of runs

Food and flavour analysis – block heaters take a column to 150 C where a Peltier chamber cannot reach

Multi column systems – a four column chamber keeps every column in a method at the same set point

Column temperature control is supplied with SUPERB PCB and SUPERB PCBA work when the analyser build also needs its controller board.

Sourcing and Cross-Reference

A column oven is replaced on capacity and range, not on outside size. Four 30 cm columns in one chamber is a different requirement from one column in a block, and a unit that meets the temperature range but not the capacity will change the method even though it fits the bench.

Block heaters are simpler: the column outside diameter, the column length and the block length decide the part, and the controller is separate. That separation is useful, because the block and its element wear while the controller usually does not, and replacement blocks are available on their own.

Where a method is already validated, the set point stability matters more than the headline range. A unit that holds 0.1 C will reproduce a retention time; one that drifts a degree will not, whatever its maximum temperature says. We quote the stability figure with the range rather than after it.

Controller boards for ovens and blocks run through SUPERB Assembly before the chamber is calibrated.

Q: Can you supply a replacement heater block without a new controller?

A: Yes. SUPERB Tech supplies heater blocks as separate parts so a damaged block does not require a new controller.

Why Choose SUPERB for Column Temperature Control

  1. Capacity before size: the replacement is matched on columns held and length, which is what changes a method
  2. Stability stated: the control stability is quoted with the range, because that is what holds a retention time
  3. Blocks sold apart: a worn block is replaced without buying a controller again
  4. Valve heating available: a heated valve position removes the cold transfer line that causes peak broadening

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Rotary and Injection Valves, Sample Loops and Injection Loops, Inline Fluid Heaters and Peltier Chillers, Needle and Metering Valves, Tube Fittings and Ferrules, Bubble Traps and Debubblers.